1. AEF630TX.zip Driver
2. INSTALL.TXT File Contents

INSTALL.TXT Driver File Contents (AEF630TX.zip)

		     Remote Boot (RPL) for Windows NT
		  ======================================

Introduction
============
    This document describes the procedure to use the Remote Boot-ROM (RPL)
    for AEF-360TX Family PCI Fast Ethernet Adapter in Windows NT Server.


Installation Procedure
======================
    1. Installing the Remoteboot Service on the Server.
       a. Choose Control Panel, Network, Add Software, Remoteboot Service,
	  put NTAS CD or disk they will be installed Remoteboot Service.

       Note: To install RPL server before, you must be had installed DLC
	     and NetBEUI protocol in your NTAS.

    2. Sharing RPLFILES files and to install MS-DOS Files for Remoteboot
       workstation.
       a. Sharing \\systemroot\rpl\rpl\rplfiles to V:\\RPLFILES
	  ;use File manager sharing
       b. Copy all the MS-DOS 6.22 ver files to
	  ----> \\systemroot\RPL\RPLFILES\BINFILES\DOS622

	  copy c:\dos\*.* V:\BINFILES\DOS622
	  attrib -s -h c:\io.sys
	  attrib -s -h c:\msdos.sys
	  copy c:\io.sys V:\BINFILES\DOS622
	  copy c:\msdos.sys V:\BINFILES\DOS622
	  attrib +s +h c:\io.sys
	  attrib +s +h c:\msdos.sys

    3. Creating Remoteboot configuration for new adapter
       a. copy the MS-DOS device driver (NDIS2) for the AEF-360TX adapter
	  to the \\systemroot\RPL\BBLOCK\NDIS directory
	  (RTSND.DOS NDIS2 driver)


       b. Create this directory \\systemroot\RPL\BBLOCK\NETBEUI\RTL8139 and
	  copy RTL8139.CNF, protocol.ini files
       c. use RPLCMD utility to add a bblock record for new adapter.
       d. In MS-DOS Prompt type <1> NET START RemoteBoot
				<2> RPLCMD
       e. Screen will display under line option and you following these do it.

	  Adapter Boot Config Profile Service Vendor Wksta [Quite] V
	  Add Del Enum: A
	  VendorName=525439
	  VendorComment=RTL8139

	  Adapter Boot Config Profile Service Vendor Wksta [Quite] B
	  Add Del Enum:A
	  BootName=DOSY
	  VendorName=525439
	  BbcFile=BBLOCK\NETBEUI\RTL8139\RTL8139.CNF
	  BootCommet=Name of this adapter
	  WindowsSize=0

	  Adapter Boot Config Profile Service Vendor Wksta [Quite] C
	  Add Del Enum:A
	  ConfigName=DOS622X
	  BootName=DOSY
	  DirName=DOS
	  DirName2=DOS622
	  FitShared=FITS\DOS622.FIT
	  FitPersonal=FITS\DOS622P.FIT
	  ConfigComment=DOS 6.22 <Adapter name>
	  DirName3=
	  DirName4=

       f. Shutdown Windows NTAS server, and reboot it.

    4. Login Administrator to NTAS server.

    5. Starting Remoteboot service and Remoteboot manager
       a. In MS-DOS Prompt type " NET START Remoteboot "
       b. In Network administrator, Remoteboot Manager
	  <1> Choose Remoteboot, New Profile, created a RTL8139 Profile Name
	  <2> Add new workstation for RTL8139 adapter and choose RTL8139
	      Profile file.

    6. To config RTL8139 card "Node ID (525439******)" and Running BootROM
       of RTL8139 Card .

       Note: If the new workstation Node ID is not match for yours, you
	     can use "Convert Adapters" in Remoteboot option.