Read Me - 4720/4710/4700 Export Module.txt
February 2001
Kodak photo printer 4720/4710/4700
Export Module for Windows 2000/NT 4.0/Win 95/Win 98.
Version Number: 2.0.1
-----------------------------------------------------------------
Contents:
=========
Introduction to the Installation Package
Contents of the Installation Package
Instructions for Printing this ReadMe File
Installing Windows custom driver
Uninstalling Windows custom driver
Helpful Hints
Introduction to the Installation Package:
=========================================
Welcome to the installation package for the Kodak photo printer
4720/4710/4700 Export Module for Windows 2000/NT 4.0/Win 95/Win 98.
This document contains information to help you install and use
the custom driver for Windows 2000/NT/95/98.
IMPORTANT FOR "NT" USERS ONLY!
Before using the printer driver, make sure your PC's
parallel port configuration in the BIOS is set to ECP
mode. The BIOS is accessed by holding down a specific
key while your PC is starting. Most computers display
which key to hold down during the start up process.
(Typically, it is either the DEL, F1, or ESC key.)
Contents of the Installation Package:
=====================================
The installer installs the following files at the locations
shown below (Folder will be created if they do not exist:
(Note: the Drive C:\ can change according to
where the users system is located)
"NT Install"
C:\Winnt\Kodak\Plug-ins (Printing)\kdk4700.8be
C:\Winnt\Kodak\Plug-ins (Printing)\
Media Files\Kodak 47xx Media V160r2.RTB
C:\Winnt\system32\Ekswex03.sys
"95/98 Install"
C:\Windows\Kodak\Plug-ins (Printing)\kdk4700.8be
C:\Windows\Kodak\Plug-ins (Printing)\
Media Files\Kodak 47xx Media V160r2.RTB
C:\Windows\system\Ekswex03.vxd
Instructions for printing this ReadMe file:
===========================================
To print this ReadMe file from Notepad.exe:
1) Select "File/Page Setup" from the menu bar to
display the "Page Setup" dialog box.
Change the left and right margin values to 0.5.
2) Select "File/Print" from the menu bar. The font
is set to Fixedsys.
Installing Windows custom driver:
=======================================
1. On Windows 2000, NT, 95 or 98 click on the START menu, select
Run... and locate the file setup.exe.
2. Follow the instructions as the installer guides you through
the installation.
3. It is highly recommended that the default destination folder
listed be selected to install the software.
4. Restart your computer after the installation process has
been completed.
IMPORTANT NOTE: This product uses the latest InstallShield 6.x version.
After clicking on setup.exe, the first screen you should come to
is the Welcome screen that has the greeting "Welcome to Kodak
photo printer 4720/4710/4700 Export Module Setup. If that screen
appears then install as per the instructions. If however a screen
comes up with
(Welcome
Modify, repair, or remove the program)
then the installer has detected that you currently have 1 or more
files already installed. Choose Remove and follow the instructions,
then reclick on setup.exe and you should now have the screen first
mentioned above. Follow the instructions now and this will insure
you have a fresh install of all needed files.
Uninstalling Windows custom driver:
=======================================
When uninstalling this product click on the setup.exe program.
The Setup screen with
(Welcome
Modify, repair, or remove the program)
will appear if the installer detects any installed files. Simply
select the remove button and click on the "Next" button and
follow the instructions.
Helpful Hints Using the Kodak Calibration Application Version 1.1.0:
===================================================================
1. When clicking on the Select Printer... button in the "Easy Cal
Step 2 of 5" dialog the software will attempt to contact the
printer to find out information about the printer. This
information is then used to fill in the Select Dialog. On some
computers the first attempt to contact the printer can fail
and the dialog will remain gray. Clicking Update will eventually
retrieve the needed information.
2. If a paper jam occurs in the area of the bottom door of the
printer, the printer will need to be reset. This reset can
happen if the paper tray is removed and then reseated back
into the slot or the printer can be power cycled off and on.
3. If any problems are encountered please refer to KODAK
Digital Science Calibration Utility User's guide.
4. The Kodak photo printer 4720\4710\4700 export module will appear
in Photoshop's list of export modules. However this export is
intended for use with Kodak calibration only and does not
support printing from Adobe Photoshop. A dialog will appear
with this information if the Kodak 4720\4710\4700 Printer is
selected.
-----------------------------------------------------------------
Copyright (C) 2000-01 Eastman Kodak Company. All rights reserved.
Kodak is a registered trademark of the Eastman Kodak Company.
Microsoft and Windows are registered trademarks
of Microsoft Corporation.
All other brand or product names are trademarks or registered
trademarks of their respective holders.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.