ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Installation for Windows 95 OSR2 ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
A. Installing the Driver on Windows 95 OSR2:
The DC21X4 based adapters are autodetected by Windows95.
To install the driver follow the menu driven
driver's installation.
B. Parameters
To overwrite the initial values set by the EISA Configuration
Utility (ECU) or overwrite the driver's default values,
add or edit the following values in the Registry
Parameters subtree:
ConnectionType:
--------------------------------------------------------------------
Digital Semiconductor 21040 based Ethernet Controller
--------------------------------------------------------------------
o AutoDetect In AutoDetect mode the driver
checks first the Twisted Pair port.
If the Link Test fails the driver
checks the BNC port. If no carrier is
detected the driver switches to the AUI
port.
o 10BaseT (TP)
o 10BaseT (TP) Full Duplex To connect to Full Duplex hubs
o 10BaseT (TP) No_Link_Test To connect hubs not supporting
the Link Integrity Test
o 10Base2 (BNC) BNC connector
o 10Base5 (AUI) 15_pin connector
--------------------------------------------------------------------
Digital Semiconductor 21041 based Ethernet Controller
--------------------------------------------------------------------
o AutoSense Senses dynamically the media ports
supported by the adapter. The precedence
is TP,BNC and AUI.
o 10BaseT (TP)
o 10BaseT (TP) Full Duplex To connect to Full Duplex hubs
o 10BaseT (TP) No_Link_Test To connect hubs not supporting
the Link Integrity Test
o 10Base2 (BNC) BNC connector
o 10Base5 (AUI) 15_pin connector
--------------------------------------------------------------------
Digital Semiconductor 2114x based 10/100 mbps Ethernet Controller
--------------------------------------------------------------------
o AutoSense Senses dynamically the media ports
o 10BaseT (TP) To connect 10BaseT Ethernet hubs
o 10BaseT (TP) Full Duplex To connect 10BaseT Full Duplex hubs
o 10Base2 (BNC) BNC connector
o 10Base5 (AUI) 15_pin connector
o 100BaseTx (TP 100) To connect 100BaseTx Ethernet hubs
o 100BaseTx (TP 100) FDx To connect 100BaseTx Full Duplex hubs
o 100BaseT4 To connect 100BaseT4 Ethernet hubs
o 100BaseFx To connect 100BaseFx Ethernet hubs
CacheLineSize = { 16 | 32 | 64 | 128 }
16 bytes
32 bytes (default)
64 bytes
128 bytes
ExtraReceiveBuffers = {value}
Number of buffers allocated by the
driver in the Receive look_aside list.
ExtraReceivePackets = {value}
Number of packets preallocated by the
driver.
InterruptMitigation = {Enabled | Disabled} (21140,21143/2)
Enable/disable the Interrupt Mitigation
algorithm.
InterruptThreshold = {number_of_interrupt/second} (default: 500)
Maximum number of interrupt/second allowed before
the Receive and Transmit interrupts get masked.
Meaningfull only when InterruptMitigation is enabled.
FrameThreshold = {number_of_frame/second} (default: 400)
Minimum number of processed frame/second allowed
before the Receive and Transmit interrupts get
unmasked.
Meaningfull only when InterruptMitigation is enabled.
MemoryReadMultiple = { Disabled | Enabled } (21142,21143 only)
Enable/disable PCI Memory_Read_Multiple command.
MRM should be enabled when the DC21X4 is connected
to the TI1130 PCI/CardBus bridge.
NwayProtocol = { Enabled | Disabled } (21041 and
21142 Rev1.0,1.1 only)
Enable/disable the 10BT/10BT_Full Duplex Autonegotiation
medium in Autosense mode.
ReceiveBuffers = {8..64}
Number of buffers allocated by the
driver in the Receive ring.
SoftwareCRC = { 0 | 1 } (21040 rev 1.x, 2.0 & 2.2 only)
0 The CRC is generated by the adapter
1 (default) The CRC is generated by software for
transmit packets bigger than the transmit threshold.
NOTE: This option affects performances and could be
disabled if the adapter does not report transmit
underruns in its statistic counters
UnderrunRetry = {2,4,6,8}
Maximun number of retransmission attempts of
an underrun packet.
UnderrunThreshold = {10,20,50,100} (21140,21143/2 only)
Maximun number of underrun occurences before the
controller switches to the next threshold value.
NoCableIndication = {Enabled | Disabled}
Check the LinkStatus before sending a packet and
retrieves NDIS_STATUS_NO_CABLE if there is not Link
indication. When it is disabled, it will retrieve the
NDIS_STATUS_SUCCESS message (workaround for the Win95
wrapper handling problem of the NO_CABLE status message).
The following values allow to overwrite the DC21X4 default setting.
Refer to the Digital Semiconductor 2104x/2114x 10/100 mbps Ethernet Controller
Engineering specifications for detailed description:
BackPressure = { 0 | 1 } (not 21040 rev1)
CSR6<BP> 0 Disabled (default)
1 Enabled
BurstLength = { 0 | 1 | 2 | 4 | 8 | 16 | 32 }
CSR0<PBL> 0 unlimited (default) - (not 21040,
21041 & 21140 rev1)
1 doubleword
2 doublewords
4 doublewords
8 doublewords
16 doublewords (default for 21040,
21041 & 21140 rev1)
32 doublewords (not 21040 & 21041)
CaptureEffect = { 0 | 1 } (not 21040 rev1)
CSR6<CA> 0 Disabled (Default)
1 Enabled
FifoArbitration = { 0 | 1 }
CSR0<BAR> 0 Rcv/Txm Arbitration (default)
1 Round_Robin
SnoozeMode = {Enabled|Disabled}
CFDA<SM> 0 Disabled
1 Enabled
StopBackoffCounter = { 0 | 1 } (not 21040 rev1)
CSR6<SB> 0 Disabled (Default)
1 Enabled
StoreAndForward = {Enabled|Disabled} (21140, 21143/2 only)
Select the StoreAndForward mode if high
PCI latencies causes 100Mbps Transmit Underruns
CSR6<SF> 1 Enabled
0 Disabled
TransmitThreshold = {value}
Transmit Threshold values for 10Mbps media.
CSR6<TTM,TR> 72 bytes
96 bytes
128 bytes
160 bytes
TransmitThreshold100 = {value} (21140, 21143/2 only)
Transmit Threshold values for 100Mbps media.
Meaningless when StoreAndForward is set
CSR6<TTM,TR> 128 bytes
256 bytes
512 bytes
1024 bytes
C. Driver Revision number
To retrieve the driver revision number, query the Registry:
HKEY_LOCAL_MACHINE\
System\CurrentControlSet\Services\Class\Net\"num"\NDIS
MajorDriverVersion
MinorDriverVersion
D. Error messages
DC21X4_ERRMSG_REGISTRY 0x01
DC21X4_ERRMSG_ALLOC_MEMORY 0x02
DC21X4_ERRMSG_SROM 0x03
DC21X4_ERRMSG_MEDIA 0x04
DC21X4_ERRMSG_LOAD_CAM 0x05
DC21X4_ERRMSG_SYSTEM_ERROR 0x06
DC21X4_ERRMSG_TXM_JABBER_TIMEOUT 0x07
1. Driver initialization errors:
o NDIS_ERROR_CODE_UNSUPPORTED_CONFIGURATION
DC21X4_ERRMSG_REGISTRY
The AdapterType Registry's key is missing or its value is
unsupported by the adapter board
o NDIS_ERROR_CODE_ADAPTER_NOT_FOUND
No board matching the AdapterCFID Registry's key value was found
plugged into the PCI bus or in the slot specified in the Registry
o NDIS_ERROR_CODE_OUT_OF_RESOURCES
DC21X4_ERRMSG_ALLOC_MEMORY
Not enough memory to allocate space for the Adapter data block
o NDIS_ERROR_CODE_INVALID_VALUE_FROM_ADAPTER
DC21X4_ERRMSG_SROM
Invalid data read from the adapter's serial ROM
o NDIS_ERROR_CODE_NETWORK_ADDRESS
No readable burnt_in or software configured station address
o NDIS_ERROR_CODE_UNSUPPORTED_CONFIGURATION
DC21X4_ERRMSG_MEDIA
The selected media port is not supported by the board.
o NDIS_ERROR_CODE_INTERRUPT_CONNECT
Interrupt initialization failed
o NDIS_ERROR_CODE_TIMEOUT
DC21X4_ERRMSG_LOAD_CAM
DC21X4 CAM initialization failed
2. Driver run time errors:
o NDIS_ERROR_CODE_HARDWARE_FAILURE
DC21X4_ERRMSG_SYSTEM_ERROR
System_Error interrupt (bus parity error)
o NDIS_ERROR_CODE_HARDWARE_FAILURE
DC21X4_ERRMSG_TXM_JABBER_TIMEOUT
Transmit Jabber timer expired
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.