=================================================================
STMicroelectronics Inc.
STMicroelectronics STE10/100 Fast Ethernet PCI Adapter
NDIS DRIVER FOR DEC PATHWORK INSTALLATION
Copyright 1995-1999 STMicroelectronics Inc.
All rights reserved.
=================================================================
Contents:
A. File Description
B. Driver Installation for NetWare Server 4.11, 5.0
C. Driver Installation for DOS32
D. Driver Installation for Microsoft Windows 3.x
E. Driver Installation for Microsoft Windows 95
F. Parameters Description for STE100.LAN
G. Driver Installation for OS/2 Workstation
A. File Description
--------------------
-------------------------------------------------------------------------------
Filename Description
-------------------------------------------------------------------------------
README.TXT This file. Presents a summary of the contents for
NetWare Client32 driver installation.
STE100.LAN STMicroelectronics Client32 ODI driver for STMicroelectronics
STE100 Adapter. This driver complies with NetWare ODI Server
driver SPEC 3.31.
STE100.LDI The driver (STE100.LAN) installation information file for
NetWare Server 5.0(Moab), 4.11, NeDOS32, Microsoft Windows 3.x.
STE100.INF The driver (STE100.LAN) installation information file for
Microsoft Windows 95.
-------------------------------------------------------------------------------
B. Driver Installation for NetWare Server 4.11, 5.0
1. Change directory to NetWare Server directory (for example:
CD\NWSERVER )
2. Load NetWare Server System by typing SERVER, then press <Enter>.
3. When the Server prompt appears, load the NetWare Server
Installation Utility. That is,
:LOAD INSTALL <- If you use NetWare 4.11
:LOAD NWCONFIG <- If you use Netware 5
4. Select "Driver options" from "Installtion Options" menu, then
press <Enter>.
5. Select "Configure network drivers" from "Driver Options" menu,
then press <Enter>.
6. Select "Select a driver" from "Additional Driver Actions" menu,
then press <Enter>.
7. Press <Ins> to install an unlisted driver, then press <F3> to
specify a different path.
8. Insert STMicroelectronics STE10/100 Fast Ethernet PCI Adapter
Driver Diskette to your PC's floppy drive and specify the drive
(A: or B:).
9. Select "STMicroelectronics STE10/100 Fast Ethernet PCI Adapter
" from "Select a driver to installed:" menu, then press <Enter>.
10. If necessary, select "Select/Modify driver parameters and
protocols" from "Board STE100_1 (Driver STE100) Actions" menu,
then press <Enter> to set up the driver parameters. (Please refer
to content F.)
Otherwise, select "Save parameters and load driver", then press
<Enter>.
11. Following instructions to complete the driver installation.
12. Sample AUTOEXEC.NCF for NetWare Server
AUTOEXEC.NCF (one board)
========================
LOAD C:STE100 FRAME=ETHERNET_802.2 NAME=E_8022
LOAD C:STE100 FRAME=ETHERNET_802.3 NAME=E_8023
LOAD C:STE100 FRAME=ETHERNET_II NAME=E_II
LOAD C:STE100 FRAME=ETHERNET_SNAP NAME=E_SNAP
BIND IPX E_8022 NET=10
BIND IPX E_8023 NET=20
BIND IPX E_II NET=30
BIND IPX E_SNAP NET=40
AUTOEXEC.NCF (two boards)
=========================
LOAD C:STE100 SLOT=10001 FRAME=ETHERNET_802.2 NAME=E_8022_1
LOAD C:STE100 SLOT=10001 FRAME=ETHERNET_802.3 NAME=E_8023_1
LOAD C:STE100 SLOT=10001 FRAME=ETHERNET_II NAME=E_II_1
LOAD C:STE100 SLOT=10001 FRAME=ETHERNET_SNAP NAME=E_SNAP_1
LOAD C:STE100 SLOT=10002 FRAME=ETHERNET_802.2 NAME=E_8022_2
LOAD C:STE100 SLOT=10002 FRAME=ETHERNET_802.3 NAME=E_8023_2
LOAD C:STE100 SLOT=10002 FRAME=ETHERNET_II NAME=E_II_2
LOAD C:STE100 SLOT=10002 FRAME=ETHERNET_SNAP NAME=E_SNAP_2
BIND IPX E_8022_1 NET=10
BIND IPX E_8023_1 NET=20
BIND IPX E_II_1 NET=30
BIND IPX E_SNAP_1 NET=40
BIND IPX E_8022_2 NET=50
BIND IPX E_8023_2 NET=60
BIND IPX E_II_2 NET=70
BIND IPX E_SNAP_2 NET=80
C. Driver Installation for DOS32
1. If you have installed the NetWare Client 32 for DOS,
all you have to do is modify STARTNET.BAT. Please see the
sample STARTNET.BAT below these installation instructions.
2. Run INSTALL.EXE from NetWare DOS 32 diskette (or from NetWare CD).
When the product manual appears, check the "NetWare Client 32 for DOS"
item, then press <Enter>.
3. Select "OTHER DRIVERS" item from "32-bit Network Board Drivers" menu,
then press <Enter>.
4. Insert STMicroelectronics STE100 Driver Diskette into your floppy diskette drive,
then specify the driver path like A: or B:.
5. Select "STMicroelectronics STE10/100 Fast Ethernet PCI Adapter driver",
then press <Enter>.
6. Refer to Content F. and set the correct driver parameters to comply
with your network environment, then press <F10> to continue.
7. Following instructions to complete the Client32 for DOS software
installation.
8. Reboot your machine.
Sample STARTNET.BAT for DOS32.
==============================
SET NWLANGUAGE=ENGLISH
C:\NOVELL\CLIENT32\NIOS.EXE
LOAD C:\NOVELL\CLIENT32\LSLC32.NLM
LOAD C:\NOVELL\CLIENT32\CMSM.NLM
LOAD C:\NOVELL\CLIENT32\ETHERTSM.NLM
LOAD C:\NOVELL\CLIENT32\STE100.LAN FRAME=ETHERNET_802.2
LOAD C:\NOVELL\CLIENT32\STE100.LAN FRAME=ETHERNET_802.3
LOAD C:\NOVELL\CLIENT32\STE100.LAN FRAME=ETHERNET_II
LOAD C:\NOVELL\CLIENT32\STE100.LAN FRAME=ETHERNET_SNAP
LOAD C:\NOVELL\CLIENT32\IPX.NLM
LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM
D. Driver Installation for Microsoft Windows 3.x
D.1 Please download the patch file from
ftp://ftp.novell.com/pub/updates/nw/nw312/312ptd.exe
D.2 After you patch your Netware 3.12 server.
please load a:\netware\Nw3.12\STE100.lan.
It will auto-load the newer NBI31x.nlm, MSM31x.nlm and Ethertsm.nlm.
E. Driver Installation for Microsoft Windows 95
E.1 Client 32 Driver Installation on Windows 95
=====================================================
1. Plug STMicroelectronics's STE10/100 Fast Ethernet PCI Adapter into
one of the Master PCI slots of your PCI platform.
2. Turn the power on and then boot from Windows 95.
3. Windows 95 will prompt with PCI Ethernet Controller in the New
Hardware Found dialog box.
4. Windows 95 will prompt with "STMicroelectronics STE10/100 Fast
Ethernet PCI Adapter" in the New Hardware Found dialog box.
5. Follow instructions to complete the installation.
Note: Windows 95 will ask you to key in the proper path of the
following diskette:
a. NetWare IntraWare for Windows 95 CD-ROM.
b. STMicroelectronics STE10/100 Fast Ethernet PCI Adapter
Diskette --> Insert STMicroelectronics STE100 Driver Diskette, then,
assign the path to A:\NetWare or B:\NetWare.
c. Windows 95 CD-ROM.
F. Parameter Description for STE100.LAN
The following parameters are used in STE100.LAN.
1. SLOT: specifies which adapter is enabled when multiple STE100 adapters
are found in your computer.
Ex: LOAD STE100 SLOT=1 FRAME=ETHERNET_802.2
LOAD STE100 SLOT=1 FRAME=ETHERNET_II
2. FRAME : specifies which frame type is used by the driver. Accepted
values are Ethernet_802.2, Ethernet_802.3, Ethernet_II and
Ethernet_SNAP. Multiple frame types can be enabled by the
driver by loading the same driver with different FRAME types.
Ex: LOAD STE100 FRAME=ETHERNET_802.2
LOAD STE100 FRAME=ETHERNET_802.3
LOAD STE100 FRAME=ETHERNET_II
LOAD STE100 FRAME=ETHERNET_SNAP
3. NODE : Use a different address to replace the node address burned
in EEPROM.
Ex: LOAD STE100 NODE=0200E8001122
---
All trademarks and brand names mentioned belong to their
respective owners.
G. NetWare OS2 ODI Workstation Driver Installation
==================================================
This section describes the procedure to install
the NetWare OS/2 ODI workstation driver for your adapter.
You can use the following methods to install the driver.
G.1 Install method
Requirements:
-------------
STMicroelectronics STE10/100 Fast Ethernet PCI Adapter Driver Diskette (STE100.SYS)
Driver Location: \NetWare\ODI\OS2ODI
Installation Procedure:
-----------------------
1 Run INSTALL utility for Netware OS/2 requester and follow its
instructions.
2. Assign STE100.SYS as the network interface driver name and specify
the path as A:\NETWARE\ODI\OS2ODI.
3. Insert STMicroelectronics STE10/100 Fast Ethernet PCI Adapter
Diskette into driver A. Then wait for file copy completion.
4. Choose the session support you need. For more information, please
see Netware OS/2 Requester Manual.
5. Save configuration.
6. Run CONFIGURATION UTILITY and select "THIS WORKSTATION" to modify the
NET.CFG file. (This file is located in the root directoy of OS/2 system,
you can use any text editor to modify it.)
7. Shutdown and restart the machine.
NOTE: If your OS/2 version is 2.0 or later, you must have the Netware OS/2
Requester version 2.01 or later.
G.2 Manual method
PREREQUISITES: You will need the following diskettes:
STMicroelectronics STE10/100 Fast Ethernet PCI Adapter Driver Diskette (STE100.SYS)
Driver Location: \NetWare\ODI\OS2ODI
Novell NetWare OS/2 WORKSTATION SERVICES REQUESTER diskette
Novell NetWare OS/2 WORKSTATION OS/2 Utility - 1
Novell NetWare OS/2 WORKSTATION OS/2 Utility - 2
Novell NetWare OS/2 WORKSTATION OS/2 Utility - 3
2. Make sure that the computer is at least a 286 or 386 machine that will run
OS/2 or Extended Edition OS/2.
3. Install the OS/2 Requester, referring to Novell's documentation for
NetWare Requester for OS/2 installation.
4. Copy the \NetWare\ODI\OS2ODI\STE100.SYS file from the support disk
into the NETWARE subdirectory on your hard disk.
5. Add or replace the PCIMLID.SYS command line in the CONFIG.SYS file.
Make sure it precedes the IPX.SYS command line. An example:
DEVICE=C:\NETWARE\LSL.SYS ; OS/2 Requester supported
DEVICE=C:\NETWARE\DDAEMON.SYS ; OS/2 Requester supported
DEVICE=C:\NETWARE\STE100.SYS ; STMicroelectronics STE100 supported
DEVICE=C:\NETWARE\IPX.SYS ; OS/2 Requester supported
6. Reboot the computer and log onto your network.
-----------------
INSTALLATION NOTE
-----------------
You can bind several frame types to the IPX protocol to support various
configurations -- in the Link Driver STE100 section of the NET.CFG
file.
SAMPLE:
Link Driver STE100
frame Ethernet_802.3
frame Ethernet_802.2
frame Ethernet_II
frame Ethernet_snap
protocol IPX 00 Ethernet_802.3
-- End of File --
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.