***********************************************************
DOS.TXT
***********************************************************
INSTALLATION GUIDE FOR THE SDMS 4.0 DOS DRIVERS
This file describes the features and use of the Symbios SDMS device
drivers for the DOS/Windows operating system environment. It is divided
into the following sections:
Introduction
When you need to load drivers
ASPI8XX.SYS
SYMDISK.SYS
SYMCD.SYS
Automatic Installation of SDMS for DOS/Windows
Using the DOS Installation Utility
About Your ASPI8XX.SYS Driver
Features
Description
Installing Your ASPI8XX.SYS Driver
Command Line Options
Using the /NORST Option
Using the /ASK Option
Using the /WIDTH Option
Using the /DISCONNECT Option
Using the /SYNCH_RATE Option
Using the /SYNCH_OFFSET Option
Using the /PARITY Option
Using the /EXCLUDE Option
Using the /HOST_ID Option
Using the /TIMEOUT Option
Using the /VERBOSE Option
Troubleshooting
About Your SYMDISK.SYS Driver
Features
Description
Installing Your SYMDISK.SYS Driver
Command Line Options
Using the /ASK Option
Using the /UNITS Option
Using the /EXCLUDE Option
Using the /SSIZE Option
Using the /SPINDOWN Option
Troubleshooting
About Your SYMCD.SYS Driver
Features
Description
Installing Your SYMCD.SYS Driver
Command Line Options
Using the /ASK Option
Using the /UPTOLUN Option
Using the /NOBCD Option
Troubleshooting
Important Additional Information For DOS Users
Assignment of Drive Letters
******************************* Introduction **********************************
In SDMS 4.0, the SCSI BIOS for the Symbios family of PCI SCSI chips is capable
of mapping SCSI hard disk drives behind any non-SCSI hard disk drives
(IDE, ESDI, etc.) within the same system. A driver-less solution will allow
connection of up to 24 hard drives (SCSI and non-SCSI) under DOS 5.0 and above.
Full Virtual DMA Services (VDS), including features such as scatter-gather,
are also supported by the SCSI BIOS. Therefore, to gain maximum
performance, you should disable any double buffer option provided by disk
caching software (such as Microsoft's SMARTDRV.EXE) for all drives
handled through SDMS.
* * * * * * * * When You Need to Load Drivers * * * * * * * * *
Connecting peripherals other than hard disk drives requires loading the
appropriate driver. Some of the drivers work together, and some are capable of
direct communication with a Symbios PCI/SCSI controller.
* * * ASPI8XX.SYS * * *
This driver is an ASPI (Advanced SCSI Programming Interface) manager which
provides standard ASPI compatibility between your SCSI host adapter hardware
and ASPI compatible applications.
* * * SYMDISK.SYS * * *
This is a device driver for non-INT13h SCSI disk drives and removable media
devices, and it works through the ASPI manager.
* * * SYMCD.SYS * * *
This is a device driver for CD-ROM drives, and it works through the ASPI
manager.
The following sections list these drivers, their features, and their
loading requirements.
********************* Installation of SDMS Drivers for DOS ******************
* * * * * * * * Using the DOS Installation Utility * * * * * *
The Symbios SDMS DOS Installation Utility provides a quick and easy method
for performing either an automatic or custom installation of the SCSI device
drivers in a DOS/Windows environment. It works with any system using an SDMS
supported Symbios SCSI chip. The DOS Installation Utility identifies the system,
scans the SCSI bus, and properly installs the needed SCSI device drivers.
The SDMS Software Device Drivers diskette that contains the DOS device drivers
also holds the DOS Installation Utility. To use the utility, insert the disk
into your floppy drive while in the DOS environment, and type:
INSTALL
Press Enter, and then follow the directions presented on the screen.
When performing a custom installation, an understanding of the information
presented in the following sections for manual installation may prove useful.
* * * * * * * * * * Troubleshooting * * * * * * * * *
Here is a potential problem and a suggested solution:
If a menuing system exists in CONFIG.SYS and multiple menu selections are available
that already include some of our drivers, Symbios only updates the first menu selection
found that already contains our drivers rather than all of them. However, if Symbios
drivers are not present, it will put the new drivers in the common area and create a
common menu item one if it does not exist.
A workaround regarding menuing in the CONFIG.SYS is to ensure the install program puts
the drivers where you want them. By default they are put in the common area. However,
if some of the Symbios drivers are already present, the install program may incorrectly
guess where the new ones should be put.
************************* About Your ASPI8XX.SYS Driver ***********************
* * * * * * * * * * * * Features * * * * * * * * * * * *
o Supports Advanced SCSI Programming Interface (ASPI) applications
o Supports up to eight host adapters
o Releases initialization code for smaller runtime size
o Works with or without a SDMS 3.0 or SDMS 4.0 Bootrom
o Performs synchronous negotiation
o Supports target initiated negotiation
o Performs Wide SCSI
o Has full Virtual DMA Services (VDS) support, including scatter-gather
o Allows Disconnect/Reselect
o Supports adapter exclusion
o Allows shared interrupts
o Supports single-threaded I/O
o Supports DMI Non-Volatile Storage (NVS) (can read device configuration
information from NVS when NVRAM is not present for the device)
o Support for Symbios usage of PCI Subsystem ID to control various
features and configuration settings (See PCI Subsystem ID
Definitions for SCSI Class, rev. 1.03, dated 5/28/97)
o Supports booting from a CD-ROM
o Supports up to Ultra3 SCSI (160 MBytes/Sec when using Wide SCSI) including:
Parallel Protocol Request
Double Transition data transfers
Cyclic Redundancy Check
* * * * * * * * * * * * Description * * * * * * * * * * *
* * * ASPI8XX.SYS * * *
This driver is an ASPI manager that provides an interface to popular ASPI
applications. It is required when you want to use SYMDISK.SYS or SYMCD.SYS, or
whenever you want to run an ASPI application.
This interface replaces an SDMS BIOS (if present), and fully supports all devices
supported by the BIOS. If an SDMS BIOS is not present, only an ASPI interface
is provided.
*********************** Installing Your ASPI8XX.SYS Driver *********************
To install the ASPI8XX.SYS driver, follow these steps:
1. Use the COPY command to copy the ASPI8XX.SYS driver from the SDMS SCSI
Drivers diskette to your boot disk.
2. Add this line to the system's CONFIG.SYS file:
DEVICE=C:[path]ASPI8XX.SYS
This line must appear before any line loading other SDMS drivers (such as,
SYMCD.SYS, SYMDISK.SYS), or any other ASPI compliant driver/application.
* * * * * * * * * * Command Line Options * * * * * * * * * *
The ASPI8XX.SYS driver has several configurable features that are set via
switches on the command line in your CONFIG.SYS file.
The command line options are as follows and the usage is detailed below:
/NORST, /ASK, /WIDTH (or /W), /DISCONNECT (or /DC), /SYNCH_RATE (or /SR),
/SYNCH_OFFSET (or /SO), /PARITY (or /P), /EXCLUDE (or /X), /HOST_ID (or /ID),
/TIMEOUT (or /T), /VERBOSE (or /V)
In the following descriptions, "path" refers to the adapter number (boot order
designation), and "id" refers to the SCSI ID. The following conventions are also
used:
[ ] items in brackets are optional
* means repeat item 0 or more times
IMPORTANT: No spaces are allowed within a single command line option, but
spaces are required between different command line options. Using
these command line options will override the settings in the SCSI
BIOS Configuration Utility.
* * * Using the /NORST Option * * *
This option prevents a SCSI bus reset during loading of ASPI8XX.SYS.
For example, if a SCSI bus reset is not desired during load, the line
in the CONFIG.SYS file that loads ASPI8XX.SYS would look like this:
DEVICE=C:[PATH]ASPI8XX.SYS /NORST
* * * Using the /ASK Option * * *
This option prompts at system boot-up time about loading the
ASPI8XX.SYS driver.
Option Syntax: /ASK
For example, to activate this option, the line in your CONFIG.SYS
file that loads ASPI8XX.SYS should look like this:
DEVICE=C:[PATH]ASPI8XX.SYS /ASK
* * * Using the /WIDTH (or /W) Option * * *
The width parameter defines the maximum data width negotiated with a device.
This option is used with host adapters capable of 16-bit data transfers. Valid
settings are 8 or 16.
Option Syntax: /WIDTH=n<path[:id]>[,n<path[:id]>]*
For example, if your first host adapter (boot order designation = 0) is a
16-bit adapter, and you wish to force 8-bit transfers to a device at
SCSI ID 2, the line in the CONFIG.SYS file that loads ASPI8XX.SYS
should look like this:
DEVICE=C:[PATH]ASPI8XX.SYS /WIDTH=8<0:2>
* * * Using the /DISCONNECT (or /DC) Option * * *
This option allows a device to disconnect since SCSI devices have the ability
to disconnect from the bus during an I/O transfer. If a particular host
adapter has parity checking disabled, all devices attached to it must have
disconnects disabled, since parity is required during the reselection phase.
Valid options are ON (allow disconnects) or OFF (do not allow disconnects). The
default for all devices is ON.
Option Syntax: /DISCONNECT=n<path[:id]>[,n<path[:id]>]*
For example, to disable disconnects on the device attached to the first host
adapter (boot order designation = 0) at SCSI ID 2, the line in the CONFIG.SYS
file that loads ASPI8XX.SYS should look like this:
DEVICE=C:[PATH]ASPI8XX.SYS /DISCONNECT=OFF<0:2>
* * * Using the /SYNCH_RATE (or /SR) Option * * *
This option sets the maximum synchronous transfer rate (in mega transfers per
second) to negotiate with a particular device. The allowable values are 0, 5, 10,
20, 40 and 80 providing the host adapter is capable of the specified speed.
Specify 0 (zero) to turn off synchronous transfers for a particular device.
The default value is the fastest rate supported by your host adapter.
Option Syntax: /SYNCH_RATE=n<path[:id]>[,n<path[:id]>]*
For example, to turn off synchronous transfers to the device attached to the
first host adapter (boot order designation = 0) at SCSI ID 3, the line in the
CONFIG.SYS file that loads ASPI8XX.SYS should look like this:
DEVICE=C:[PATH]ASPI8XX.SYS /SYNCH_RATE=0<0:3>
Note: When executing synchronous transfers using an 8-bit SCSI bus,
mega bytes per second = mega transfers per second. Also, when you are
doing synchronous transfers using a 16-bit SCSI bus, mega bytes
per second = 2 * mega transfers per second.
* * * Using the /SYNCH_OFFSET (or /SO) Option * * *
This option sets the maximum synchronous offset in bytes used to negotiate
with a particular device. The maximum allowable values are 0, 8, 16 and 31
provided the host adapter is capable of the specified offset. Specify 0 (zero)
to turn off synchronous transfers for a particular device.
The default value is the fastest rate supported by your host adapter.
Option Syntax: /SYNCH_OFFSET=n<path[:id]>[,n<path[:id]>]*
For example, to turn off synchronous transfers to the device attached to the
first host adapter (boot order designation = 0) at SCSI ID 3, the line in the
CONFIG.SYS file that loads ASPI8XX.SYS should look like this:
DEVICE=C:[PATH]ASPI8XX.SYS /SYNCH_OFFSET=0<0:3>
* * * Using the /PARITY (or /P) Option * * *
This option tells the host adapter to disable the SCSI bus data integrity
checking feature known as parity. Some SCSI devices do not generate parity.
Valid options are ON (check parity) or OFF (do not check parity). The default
for all devices is ON.
Warning: When disabling parity checking, also disable disconnects for that
adapter since you cannot disable parity checking for reselection.
If a device does not generate parity, and it disconnects, the I/O
will never complete.
Option Syntax: /PARITY=n<path[,path]*>[,n<path[,path]*>]*
For example, to turn off parity checking on the first host adapter (boot order
designation = 0), the line in your CONFIG.SYS file that loads ASPI8XX.SYS should
look like this:
DEVICE=C:[PATH]ASPI8XX.SYS /PARITY=OFF<0>
* * * Using the /EXCLUDE (or /X) Option * * *
This option allows you to exclude support for an adapter that does not currently
have BIOS support. You may not exclude an adapter that is supported (included)
by the BIOS when you boot your system. This option has three required parameters:
1. PCI Device ID
2. PCI Bus Number
3. PCI Device/Function Number
These parameters identify the specific adapter you want to exclude. To obtain
these parameters, boot your system using the /VERBOSE command line option
(explained later in this section). Your monitor displays the parameters for the
adapter or path you wish to exclude.
Option Syntax: /EXCLUDE<a:b:c>[,<a;b;c>]*
For example, if you found the adapter you wish to exclude to have PCI Device
ID 3, PCI Bus Number 0, and PCI Device/Function Number 68, then the line in
the CONFIG.SYS file that loads ASPI8XX.SYS should look like this:
DEVICE=C:[PATH]ASPI8XX.SYS /EXCLUDE<3:0:68>
* * * Using the /HOST_ID (or /ID) Option * * *
This option lets you alter the SCSI ID for a host adapter. On an 8-bit adapter,
the SCSI IDs are 0-7. On a 16-bit adapter, the SCSI IDs are 0-15 (it is
suggested that IDs 8-15 not be used for your adapter). This option will not
allow you to select a SCSI ID already in use.
If the host adapter allows connection of both 8-bit and 16-bit devices to the
same bus, and the adapter number is changed to greater than 7, then the 8-bit
SCSI devices will not be able to reselect the initiator.
Note: You are not allowed to change the SCSI ID of any adapter currently
supported by the BIOS.
Option Syntax: /HOST_ID=n<path>[,n<path>]*
For example, to change the SCSI ID of your second host adapter (path=1) to ID=6
(providing that adapter is not controlled by the BIOS), the line in the
CONFIG.SYS file that loads ASPI8XX.SYS should look like this:
DEVICE=C:[PATH]ASPI8XX.SYS /HOST_ID=6<1>
* * * Using the /TIMEOUT (or /T) Option * * *
The ASPI8XX.SYS driver uses a time-out mechanism to detect certain errors. When
the driver issues a command to a SCSI device, a timer is started. If the timer
expires before the command completes, the driver assumes something has gone
wrong, and takes steps to recover. The default for this option is 10 seconds,
if the device is BIOS controlled. If the device is not BIOS controlled, the
default is 0. Also, non-volatile memory settings can alter these defaults. The
maximum setting is 0, which is no time-out. The range of allowable values is
0-65535 seconds.
Option Syntax: /TIMEOUT=n<path[:id]>[,n<path[:id]>]*
For example, you might have a particularly slow device (with SCSI ID 3) on the
first host adapter (boot order designation = 0). If you wish to extend the
time-out for this device to 60 seconds, the line in the CONFIG.SYS file that
loads ASPI8XX.SYS should look like this:
DEVICE=C:[PATH]ASPI8XX.SYS /TIMEOUT=60<0:3>
* * * Using the /VERBOSE (or /V) Option * * *
This option causes more detailed information to appear on your monitor, after
the ASPI8XX.SYS driver is initialized, during a system boot. For example, the
following may be displayed after using the /VERBOSE or /V option:
53C875 Rev 3 at PCI ID 15, Bus 0, Dev/Func 70h, CMD=0117h, SCRIPTS=FFFBE000h
This option is useful if you have multiple adapters in the system and need
to know the PCI Device ID, the PCI Bus number, and the PCI Device/Function number
for each adapter. This information is required to use the /EXCLUDE option
already described in this section.
Option Syntax: /VERBOSE
For example, to see more detailed adapter information displayed when you boot,
the line in the CONFIG.SYS file that loads ASPI8XX.SYS should look like this:
DEVICE=C:[PATH]ASPI8XX.SYS /VERBOSE
* * * * * * * * * * * * Troubleshooting * * * * * * * * * *
The following are some potential problems and their suggested solutions.
* * * Problem * * *
System Locks up at boot time.
* * * Solution * * *
a. Check for conflicts with other ASPI managers.
b. Check for correct loading sequence in the CONFIG.SYS file.
c. Boot the system.
* * * Problem * * *
The device driver does not recognize one of the non-boot SCSI peripherals
(system may lock up).
* * * Solution * * *
a. Make sure the drivers were installed in the correct sequence.
b. Make sure the drivers' CONFIG.SYS line has the correct path to the drivers.
c. Power down all units in the system.
d. Make sure all SCSI devices have unique ID numbers.
e. Make sure both ends of the SCSI bus are terminated.
f. Check all cable and power connections.
g. Boot the system.
************************ About Your SYMDISK.SYS Driver ************************
* * * * * * * * * * * * Features * * * * * * * * * * * *
o Supports up to 8 host adapters
o Supports removable media devices
o Supports magneto optical devices
o Supports non-512-byte sectors (1024, 2048, 4096)
o Supports multiple logical unit number (LUN) support
o Supports OS/2 floppy format for MO and hard disks
o Supports multiple host adapters when adapter has not been controlled by
the SCSI BIOS (no INT13h devices)
o Can reserve drive letters for installed devices without media present
in the device (see /UNITS under Command Line Options)
o Can add drive letters
o Supports power management (to spin down drives)
* * * * * * * * * * * * Description * * * * * * * * * * *
The SYMDISK.SYS driver is needed when connecting drives with non-512-byte sectors,
and when connecting removable drives if the user wants to change the media. It is also
required to obtain drive letters for devices (adapters) that are not supported
by a BIOS. SYMDISK.SYS communicates through ASPI8XX.SYS. To use the SYMDISK.SYS
driver you must load ASPI8XX.SYS also.
*********************** Installing Your SYMDISK.SYS Driver ********************
To install the SYMDISK.SYS driver, follow these steps:
1. Use the COPY command to copy the appropriate drivers from the SDMS SCSI
Drivers disk to your boot disk.
2. Add the lines shown below to the system's CONFIG.SYS file. The ASPI8XX.SYS
driver is also required. List the drivers in this sequence:
DEVICE=C:[PATH]ASPI8XX.SYS
DEVICE=C:[PATH]SYMDISK.SYS
* * * * * * * * * * Command Line Options * * * * * * * * *
The SYMDISK.SYS device driver has several embedded functions that are accessed
via switches on the command line. These options are described below, and use the
following conventions:
[ ] items in brackets are optional
* items in brackets followed by an * means repeat 0 or
more times
| choose one of the given items
IMPORTANT: No spaces are allowed in a single command line option, but spaces are
required between different command line options.
* * * Using the /ASK Option * * *
This option prompts the user at system boot-up whether to load SYMDISK.SYS or
not. To use this option, the line in the CONFIG.SYS file that loads SYMDISK.SYS should
look like this:
DEVICE=C:[PATH]SYMDISK.SYS /ASK
* * * Using the /UNITS= Option * * *
Note: Symbios recommends that this option be used when using removable
media with more than one partition.
The SYMDISK.SYS device driver allows the use of removable media, such as
cartridge hard drives, each of which might have a different number of partitions.
If media with more than one partition are used, set this option to the maximum
number of partitions on any one media. To use this option, the line in the
CONFIG.SYS file that loads SYMDISK.SYS should look like this (all on one line):
DEVICE=C:[PATH]SYMDISK.SYS /UNITS=path:id:lun:num_units
[,path:id:lun:num_units]*
For example, if there is a removable media drive at SCSI ID 2 on the first host
adapter, and you need to reserve three partitions, the command line should look
like this:
DEVICE=C:[PATH]SYMDISK.SYS /UNITS=0:2:0:3
When SYMDISK.SYS initializes, it defaults to either:
a. One drive letter for a removable media device with no media present.
-OR-
b. The number of partitions found on the media in the removable media
device.
Note: The full path, id, lun, and num_units values are required for this option.
Also, there is a limit of 24 devices.
* * * Using the /EXCLUDE= Option * * *
This option allows a user to exclude a "path:id:lun" combination from
being scanned or controlled by SYMDISK.SYS. The path parameter is mandatory
with all ids and luns for that path excluded by default if just the path is
specified. To use this option, the line in the CONFIG.SYS file that loads
SYMDISK.SYS should look like this:
DEVICE=C:[PATH]SYMDISK.SYS /EXCLUDE=path[:id[:lun]]
[,path[:id[:lun]]]*
For example, if the path is 0, id 2, and lun 0, the command line should look
like this:
DEVICE=C:[PATH]SYMDISK.SYS /EXCLUDE=0:2:0
Note: There is a limit of 24 "path:id:lun" combinations allowed.
* * * Using the /SSIZE= Option * * *
The SYMDISK.SYS device driver defaults to the largest sector size found during
boot, handling all different sector sizes found. In the case of removable media,
SYMDISK.SYS assumes a 2048 byte sector size when no media is present. This
option overcomes this limitation. To use this option, the line in the CONFIG.SYS
file that loads SYMDISK.SYS should look like this:
DEVICE=C:[PATH]SYMDISK.SYS /SSIZE=512|1024|2048|4096
For example, if a removable media drive is used that has a sector size of 2048
bytes, the command line should look like this:
DEVICE=C:[PATH]SYMDISK.SYS /SSIZE=2048
Note: If SYMDISK.SYS comes across a sector size larger than the one specified
in this option, or if it finds a sector larger than the default, it will
refuse to read/write to that media. It will report an invalid media error
to DOS.
* * * Using the /SPINDOWN= Option * * *
This is a power management feature that automatically spins down a disk when
the disk is not accessed for a specified amount of time. The default spindown
time is 15 minutes. You can specify a new spindown time in hours and minutes
(hh:mm) with a minimum time of 1 minute. To use this option, the line in the
CONFIG.SYS file that loads SYMDISK.SYS should look like this (all on one line):
DEVICE=C:[PATH]SYMDISK.SYS /SPINDOWN=hh:mm<path[:id[:lun]]>
[,hh:mm<path[:id[:lun]]>]
For example, to spindown a device on path 0, id 2, and lun 0, after
one hour and five minutes of inactivity, the command line should look like this:
DEVICE=C:[PATH]SYMDISK.SYS /SPINDOWN=1:5<0:2:0>
-Or-
To spindown all devices after the default time-out of 15 minutes,the command
line should look like this:
DEVICE=C:[PATH]SYMDISK.SYS /SPINDOWN=<>
Remember, the <> are required when you specify a path:id:lun in this option.
* * * * * * * * * * * * Troubleshooting * * * * * * * * * *
The following are some potential problems and their suggested solutions:
* * * Problem * * *
The computer locks up and will not complete booting from a non-SCSI hard
disk drive.
* * * Solution * * *
a. Refer to the drive manufacturer's user manual.
* * * Problem * * *
The computer locks up and will not complete booting from a SCSI hard disk drive.
* * * Solution * * *
Note: If the SCSI BIOS is seen during boot, a banner similar to the following
appears:
Symbios SDMS (TM) v4.0 PCI SCSI BIOS, PCI Rev. 2.0, 2.1
Copyright 1995 Symbios PCI-4.09.00
a. Is the SCSI BIOS seen during boot?
YES Go to b.
NO Power down all units in the system.
Remove all SCSI cables.
Boot system.
Is the SCSI BIOS seen during boot?
YES Power down all units in the system.
Reconnect and check all cable and power connections.
Boot system.
Go to a.
NO Power down all units in the system.
Reseat the host bus adapter.
Check CMOS setup.
Boot system.
Go to a.
b. Does the SCSI BIOS see the bootable SCSI drive?
Note: When the computer boots, SDMS scans the SCSI bus. Devices found on the
SCSI bus are identified as in the following lines:
HA ID LUN VENDOR PRODUCT REV
----------------------------------------------------
0 2 0 SEAGATE ST31230N 0060
0 7 0 Symbios SYM53C815 0003
YES Go to c.
NO Power down all units in the system.
Make sure the hard drives have different ID numbers (boot drive
should have lowest ID).
Make sure both ends of the SCSI bus are terminated.
Check all cable and power connections.
Check CMOS setup.
Boot system.
Go to a.
c. If boot is still unsuccessful, follow the solution to the next problem.
* * * Problem * * *
The device driver does not recognize one of the non-boot SCSI peripherals
(system may lock up).
* * * Solution * * *
a. Make sure the drivers were installed in the correct sequence.
b. Make sure the drivers' CONFIG.SYS line has the correct path to
the drivers.
c. Power down all units in the system.
d. Make sure the hard drives have different ID numbers (boot drive
should have lowest ID).
e. Make sure both ends of the SCSI bus are terminated.
f. Check all cable and power connections.
g. Boot the system.
************************** About Your SYMCD.SYS Driver *************************
* * * * * * * * * * * * Features * * * * * * * * * * * *
o Compatible with Microsoft's CD-ROM Extension 2.21 and above
o Multi-session Photo CD support
o Supports up to eight host adapters
* * * * * * * * * * * * Description * * * * * * * * * * *
The SYMCD.SYS device driver is needed whenever a CD-ROM device is connected on
the SCSI bus. You must load it in conjunction with Microsoft's CD-ROM Extension
2.21 or above (MSCDEX.EXE). SYMCD.SYS communicates through ASPI8XX.SYS, so you
must load ASPI8XX.SYS to use SYMCD.SYS.
*********************** Installing Your SYMCD.SYS Driver *********************
To install the SYMCD.SYS driver, follow these steps:
1. Use the COPY command to copy the appropriate driver(s) from the SDMS SCSI
Drivers diskette to your boot disk.
2. Add SYMCD.SYS to the CONFIG.SYS file. It goes in after ASPI8XX.SYS and
SYMDISK.SYS (if this driver is also being used), in this order:
DEVICE=C:[PATH]ASPI8XX.SYS
DEVICE=C:[PATH]SYMDISK.SYS
DEVICE=C:[PATH]SYMCD.SYS /D:NAME
Note: The /D: is not a drive letter designation; it indicates the name you wish
assigned to your CD-ROM. You must include the NAME, which can use any
combination of up to 8 characters.
3. To ensure that sufficient drive letters are available to identify all
devices connected to the SCSI bus, add the MS-DOS LASTDRIVE command to the
CONFIG.SYS file:
LASTDRIVE=x
where x specifies a drive letter in the range C through Z. The letter
assigned to LASTDRIVE represents the last valid drive MS-DOS is able to
recognize and also represents the maximum number of drives available. For
example, LASTDRIVE=K allows access to eleven (11) logical drives. For
further details about LASTDRIVE, consult your MS-DOS manual.
4. Unless your CD-ROM access software specifies otherwise, Microsoft's CD-ROM
Extension (MSCDEX.EXE) should execute from the AUTOEXEC.BAT file in order to
access your drive. Add the following line to the AUTOEXEC.BAT file:
[PATH]MSCDEX /D:NAME
For example, if:
DEVICE=C:[PATH]SYMCD.SYS /D:MY_CD
is in the CONFIG.SYS file, then:
[PATH]MSCDEX /D:MY_CD
should exist in the AUTOEXEC.BAT file. The /D: switches must match.
5. Check installation instructions for the CD-ROM drive itself for other
parameters necessary to include with MSCDEX.
6. When MSCDEX is loaded during the AUTOEXEC.BAT file execution, a message is
returned assigning a drive letter to the CD-ROM drive. For example:
DRIVE E = DRIVER MY_CD UNIT 0
This informs the user that the CD-ROM drive is recognized and ready for use.
* * * * * * * * * * * Command Line Options * * * * * * * * *
The SYMCD.SYS device driver has several embedded functions available that are
accessed via switches on the command line. An explanation of these options
follows:
IMPORTANT: No spaces are allowed in a single command line option, but spaces are
required between different command line options.
* * * Using the /ASK Option * * *
This option prompts the user at initialization time whether to load SYMCD.SYS or
not. For example, the line in the CONFIG.SYS file that loads SYMCD.SYS would look
like this:
DEVICE=C:[PATH]SYMCD.SYS /D:MY_CD /ASK
* * * Using the /UPTOLUN= Option * * *
This option changes the default for multiple LUNs per Target ID on the SCSI bus.
The current default is to scan all LUNs. CD-ROM changers that use multiple LUNs
work by default. To turn off scanning all LUNs on a SCSI bus, choose /UPTOLUN=0.
This saves some time during boot.
* * * Using the /NOBCD Option * * *
This option supports the Trantor Music Box CD audio application. Using this
option prevents the track numbers from being converted to BCD (Binary Coded
Decimal). If this option is used with CD audio applications such as Adaptec's
cdplayer, Corel's cd-audio, or Future Domain's cdaudio, track numbers >16 are
not reported correctly because these applications require binary track numbers.
For this option, the line in the CONFIG.SYS file that loads SYMCD.SYS would look
like this:
DEVICE=C:[PATH]SYMCD.SYS /NOBCD
* * * * * * * * * * * Troubleshooting * * * * * * * * * * *
The following are some potential problems and their suggested solutions:
* * * Problem * * *
The CD-ROM drive is not seen at boot time, or the system locks up.
* * * Solution * * *
a. Make sure the required drivers are installed and in the correct sequence.
b. Make sure the drivers' CONFIG.SYS line has the correct path to
the driver.
c. Make sure MSCDEX, in the AUTOEXEC.BAT, has the same drive
name as the CD-ROM driver in the CONFIG.SYS file.
d. Make sure there is no ID or drive letter designation conflict.
e. Power down all units in the system.
f. Check the cable and power connections.
g. Make sure the SCSI bus is properly terminated.
h. Make sure sufficient drive letters are specified (through the MS-DOS
lastdrive= command) to include your CD-ROM. A CD-ROM that uses multiple
disks requires a letter for each disk.
***************** Important Additional Information For DOS Users **************
* * * * * * * * * Assignment of Drive Letters * * * * * * * * *
The MS-DOS operating system assigns drive letters to primary partitions
first. After the primary partitions have been assigned drive letters the
logical partitions are assigned drive letters. Do not assume that the drive
letter designations will follow consecutively from device-to-device within a
PC system.
An Example:
A system is configured with an IDE hard disk as the boot drive, a SCSI hard
disk, and a CD-ROM drive. The IDE drive has three partitions: one primary and
two logical. The SCSI hard disk has two partitions: one primary and one
logical. The SCSI hard disk is assigned ID one, and the CD-ROM is ID four. The
distribution of the drive letters is:
A: 3 1/2" floppy drive
B: 5 1/4" floppy drive
C: IDE primary partition
D: SCSI primary partition
E: IDE first logical partition
F: IDE second logical partition
G: SCSI logical partition
H: CD-ROM
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.