Graphtec Corporation
Scanning Master 21+ (OPS112) Ver.5.30 Supplementary Information
-------------------------------------------------------------------------------
Introduction
This file provides notes on using the Scanning Master 21+.
System Requirements
OS : Windows 95/98/Me, Windows NT 4.0 Workstation
Windows 2000 Professional, Windows XP Professional/Home Edition
(Requires Windows 2000/XP if the scanner is IS200, CS600/500/
400/300 models.)
CPU : Pentium 133 MHz or higher grade
Memory : 32 MB or more
Monitor : 1024x768, 256 colors or more
Disk space amount that can contain the scanned-in data
Mouse
SCSI board : An Adaptec SCSI board (to connect the scanner via the SCSI
interface)
Network Interface : 10BASE-T/100BASE-TX (to connect the scanner via the
Network interface)
USB Interface : that comes standard with your computer (to connect the
scanner via the USB interface)
IEEE1394 Interface : (to connect the scanner via the IEEE1394 interface)
* If your scanner does not operate with the USB interface that comes with your
computer, or if your computer does not have a USB 2.0 interface, please
contact your sales representative or nearest Graphtec vendor for information
on supported add-on cards.
* Graphtec does not guarantee correct scanner operation with every IEEE 1394
computer interface or add-on card. Please contact your sales representative
or nearest Graphtec vendor for information on supported add-on cards.
Recommended Environment
For Bilevel
CPU : Pentium 200 MHz or higher grade
Memory : 64 MB or more
SCSI board : An Adaptec SCSI board - for PCI
(to connect the scanner via the SCSI interface)
Network Interface : 100BASE-TX
(to connect the scanner via the Network Interface)
USB 2.0 Interface : that comes standard with your computer
(to connect the scanner via the USB interface)
For Grayscale
CPU : Pentium III 550 MHz or higher grade
Memory : 256 MB or more
Monitor : 1024x768, High Color display
SCSI board : An Adaptec SCSI board - for PCI
(to connect the scanner via the SCSI interface)
Network Interface : 100BASE-TX
(to connect the scanner via the Network Interface)
USB 2.0 Interface : that comes standard with your computer
(to connect the scanner via the USB interface)
For 8-bit/24-bit color
CPU : Pentium III 866 MHz or higher grade
Memory : 512 MB or more
Monitor : 1024x768, True Color display
SCSI board : An Adaptec SCSI board - for PCI
(to connect the scanner via the SCSI interface)
Network Interface : 100BASE-TX
(to connect the scanner via the Network Interface)
USB 2.0 Interface : that comes standard with your computer
(to connect the scanner via the USB interface)
* If you want to scan in and edit grayscale or color data larger than A1 size,
400 dpi, you may need a memory larger than the recommended size.
Depending on the document, it may not be possible to scan in the images it
contains or the process may slow down even if the memory size is increased.
If you encounter such a problem, select Tools menu > Options > General tab and
enable "Use Work File". In addition, enable "Specify Folder" and then specify
a folder that contains sufficient available space.
Compatible Scanners
The following Graphtec scanners are compatible.
IS2100 Ver.1.00 or later
IS3100 Ver.1.00 or later
CS1000 Ver.1.00 or later
CS1000EV Ver.2.00 or later
CS1100EV Ver.1.00 or later
CS2000 Ver.1.00 or later
CS300-10 Ver.1.00 or later
CS400-10 Ver.1.00 or later
CS500-11 Ver.1.00 or later
CS500-11PRO Ver.1.00 or later
CS500-11eN Ver.1.00 or later
CS500-11eN-PRO Ver.1.00 or later
CS600-11 Ver.1.00 or later
CS600-11PRO Ver.1.00 or later
CS600-11eN Ver.1.00 or later
CS600-11eN-PRO Ver.1.00 or later
IS200-11 Ver.1.00 or later
IS200-11PRO Ver.1.00 or later
IS200-11eN Ver.1.00 or later
IS200-11eN-PRO Ver.1.00 or later
Installation
The installation process is initiated by running the SETUP.EXE file. After
installation is started, complete installation by following the instructions
appearing on the screen.
Notes on Use
1) For operating instructions, refer to the Help menu.
2) To scan in image data through the scanner, you must have a SCSI board and
ASPI manager for the ASPI that are running.
3) The standard version of Windows 95/98/Me contains an ASPI manager. However,
there are a few problems (e.g., the standard ASPI manager cannot identify
the SCSI ID automatically). Neither Windows NT 4.0 nor Windows 2000/XP
contains an ASPI manager.
If you want to use Windows 95/98/Me or Windows NT 4.0 for operation, be sure
to install the ASPI Manager provided with the SCSI board.
If you want to use Windows 2000/XP for operation, consult with your SCSI
board vendor or Adaptec distributor.
4) While using the Scanning Master 21+ to read image data from a scanner,
do not concurrently run other software to read image data from the scanner.
5) When a file is open on NetWare with Windows 95, it may not be possible to
open the Help menu in some cases. If this happens, open the Help file from
the Task Bar's Start button.
6) While editing with Windows 95/98/Me, red lines may be displayed on the
opposite side.
7) In some cases, red lines may remain while performing operations accessed
from the Edit or Tools menu.
8) When the Zoom rate is increased for display with Windows 95/98/Me, it may
not be possible to display the image in some cases.
9) With certain systems, unnecessary lines may be displayed according to the
display's Zoom rate. Such a display, however, does not signify any problem
with the data.
10) If there is another window or a task bar on top of the Details window,
the image being scanned may be imprecise, or may not be displayed.
Make sure that the windows are not overlapped.
Windows and Windows NT are the registered trademark of Microsoft Corp.
Adaptec is the registered trademark of Adaptec, Inc.
All copyrights for the Scanning Master 21+, including the right of
reproduction in whole or in part in any form, belong to Graphtec
Corporation.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.