1. LSI_SCSI.ZIP Driver
2. RedHat_readme.txt File Contents

RedHat_readme.txt Driver File Contents (LSI_SCSI.ZIP)

      Fusion MPT Package - Binary Images
====================================================

Binaries have been generated for use
with Red Hat Linux 7.0, 7.1, 7.2, ASE 2.1, 7.3.  
These binaries may be used to upgrade a driver 
without rebuilding the kernel or used to 
upgrade the driver during install

====================================================

Upgrading the Driver During Installation
-----------------------------------------

Step 1: For the version of Red Hat of interest, uncompress
        the tarball.
          
           # tar xzvf redhat70-<driver version>.tar.gz

Step 2: Transfer the driver disk image of interest to a diskette
        using dd or raw-write. For a 686-type of processor and
        Red Hat 7.0 Linux, 

            # dd if=rh70i686.img of=/dev/fd0

        Remark:  
           Red Hat installs binaries that are compatible
           with your processor. Therefore, if you have a 686-type
           processor but use the 386 install diskette,
           installation will be successful but reboot will
           fail.  The failure will be due to the 386 driver
           binaries from the diskette not being compatible 
           with the 686 binaries installed by Red Hat.

           You must select the disk that matches your system
           processor type.

           Recovery:  
               Make a bootable driver disk when the installer 
               presents the option. If the normal boot fails,
               reboot using the bootable diskette. Using the
               appropriate driver disk, install the binaries
               as in Step 5 below.  

               You must re-create your ramdisk images. First,
               # ls /lib/modules
               and write down the directory names. For example,
               you might see
                2.4.7-10  2.4.7-10smp
                
                For each directory in /lib/modules. For the example,
                # cd /boot
                # /sbin/mkinitrd -f initrd-2.4.7-10.img 2.4.7-10
                # /sbin/mkinitrd -f initrd-2.4.7-10smp.img 2.4.7-10smp

                Finally, if you installed LILO, you must re-run
                LILO,
                # lilo -v
                
                Reboot.

Step 3: Red Hat 7.0, 7.1, 7.1SBE, ASE 2.1, 7.3

        Boot the installation material. At the first screen, enter

            linux dd

        when the boot: prompt appears (the installer will then
        to prompt for the driver update diskette).

        Option for Red Hat 7.1, ASE 2.1, 7.3: 
        ------------------------------------
        Boot the installation material. At the first screen, enter

            linux dd updates

        when the boot: prompt appears (the installer will then
        to prompt for the driver update diskette and the updates disk).
        Use the same diskette for both. If the update script is
        successfully executed by the installer, Step 5 below is unnecessary.
        To determine if execution was successful, on reboot,
        log in a root.
             # cd /lib/modules
             # find -name mptbase.o
        If the script was executed successfully, mptbase.o will show once
        for each kernel directory. That is, find will return:
             2.4.7-10/kernel/drivers/message/fusion/mptbase.o
             2.4.7-10smp/kernel/drivers/message/fusion/mptbase.o

Step 3: Red Hat 7.2

        When driver update disks are used, incorrect boot 
        images are created by the Red Hat 7.2 installer.
        To use driver update disks, the user requires three (3) floppy
        diskettes.  One disk is the diskette written in Step 2 and
        contains the driver. The second disk contains a new boot image
        and the third contains patches to the Red Hat installer program.

        Step 3a: Create diskette 2. The new boot image
                 (boot.img) is available in the
                 redhat72-<driver version>.tar.gz tarball

                     # dd if=boot.img of=/dev/fd0

        Step 3b: Create diskette 3. The installer update image
                 (update_disk-20020117.img) is available in the
                 redhat72-<driver version>.tar.gz tarball

                     # dd if=update-disk-20020117.img of=/dev/fd0

                 The boot and update disk images may be obtained from:
                 ftp://updates.redhat.com/7.2/en/os/images/i386

        Step 3c: Boot the installation material. At the first screen, enter

                     linux dd updates 

                 when the boot: prompt appears (the installer will then
                 to prompt for the driver update diskette and the installer
                 update disk).
        
Step 4: Continue with normal installation.

Step 5: Once installation is complete and reboot is successful,
        execute the post-installation script. Insert the
        driver update disk into the floppy disk drive then

            # mount /dev/fd0
            # cd /mnt/floppy
            # ./post_install.scr
            # cd 
            # umount /dev/fd0

        Proceed with normal usage.