56ZLX.EXE, version 4.12.31.01 contains the
5634ZLX.INF info file for Windows NT and Windows 9x,ME,2000
as well as a DOS modem enabler called MDMEN113.EXE.
Installing the MT5634ZLX in a Windows 9x, ME, 2000 environment:
1. Insert the MT5634ZLX into the PCMCIA slot
2. Windows will detect the new hardware and launch
the modem installation wizard.
3. Copy the .INF file to a temporary folder.
4. Browse to the temporary folder and Windows will detect the INF
file for the MT5634ZLX.
5. Click "finish" and the modem is now installed.
Installing the MT5634ZLX in a Windows NT environment:
1. Make sure the PCMCIA card is plugged into the PCMCIA slot.
2. Run Windows NT 4.0.
3. Double click the Modem Icon in "Control Panel".
4. In "Install New Modem" window, press "Next" button to detect
the modem automatically.
5. Press "Change" button to change the modem type.
6. Press "Have Disk..." button.
7. Enter the path (i.e. "A:\") and press "OK" button.
8. Select the correct modem type i.e.,"PCMCIA 56kbps FAX+Modem"
and then Click "OK" to accept the modem type.
9. Click "Finish" button.
Installing the MT5634ZLX in a DOS environment:
The DOS modem enabler, MDMEN113.EXE, can be used to enable the modem on
any DOS computer not having Card Services or Socket Services. The
Enabler can be used from the DOS command line, or as a DOS driver by
loading the Enabler during AUTOEXEC.BAT or CONFIG.SYS. Use this
statement:
MDMEN113 [/COM=n] [/IRQ=dd] [/SLT=m]
Where:
COM=n specifies the COM port value. The factory default is COM=2.
IRQ=dd specifies the interrupt request number in decimal. The factory
default is IRQ4 for COM1 and COM3, or IRQ3 for COM2 and COM4.
SLT=m specifies the slot number the Fax/Modem card occupies.
The factory default is auto-detection.
For example:
MDMEN113 /COM=2 /IRQ=5 /SLT=1
Technical Notes for the enabler
1. What follows is the most typical communication software IRQ and
I/O address settings:
IRQ Number I/O Address
COM1: 4 3F8
COM2: 3 2F8
COM3: 4 3E8
COM4: 3 2E8
2. If you are using Windows 3.X, you can change the IRQ and COM
PORT under CONTROL PANEL - PORTS - ADVANCED dialog box. If you
change the COM PORT and IRQ under Windows 3.X, be sure that the
settings match the parameter in the MDMEN113.EXE command line.
3. Two COM ports cannot share the same I/O address even when the
default value is the same. If your system has COM1 and COM2
already, you may run MDMEN113 with /COM=3 and /IRQ=n where "n"
is an available IRQ other than 3 or 4. When you run a modem
application program, the COM port number and interrupt number
specified must match the parameter in the MDMEN113.EXE command
line.
Updates can be found on the Multitech site:
www.multitech.com/
Any questions can be directed to Technical Support at
763-717-5863 for international calls or tollfree within
the USA at 1-800-972-2439.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.