1. 3c319.zip Driver
2. WFWNDIS2.TXT File Contents

WFWNDIS2.TXT Driver File Contents (3c319.zip)

                        3Com (R) Corporation
                     TokenDisk (R) Diskette for
  The 3C319 TokenLink Velocity ISA Token Ring Network Interface Card
          NDIS 2.01 Drivers and Windows for Workgroups 3.11 


NOTE: 3Com recommends that you use the 32-bit NDIS 3 driver with Windows
      for Workgroups (WFW).  Your system performance will be maximized 
      if you install the NDIS 3 driver instead of the NDIS 2 driver.

The real-mode 16-bit NDIS 2 (TLNK3.DOS) driver does not support Plug and 
Play configuration of the NIC.  Before installing the driver, use the
Configuration and Diagnostic Program (3TRDIAG.EXE) to disable PnP and 
configure the NIC.

The following describes the procedure for installing the real-mode 16-bit
NDIS2 (TLNK3.DOS) driver under WFW.  

NOTE: It is assumed that Windows for Workgroups has already been
      installed.

1.  Start Windows.
    
2.  Open the Network group and double-click Network Setup.

3.  To install the network adapter, click Drivers...

4.  In the Network Drivers window, click Add Adapter...

5.  From the list of network adapters, select Unlisted or Updated Network
    Adapter.

6.  Network setup requires a vendor-provided network driver diskette. 
    Insert the TokenDisk diskette in drive A:, and type the path for the 
    NDIS driver:
 
    A:\WFW311

    Then click OK.

7.  From the Unlisted or Updated Network Adapter screen, select 3Com 
    TokenLink Velocity ISA NIC (3C319) and click OK.

8.  From the Network Drivers screen, click Setup.

9.  To select the NDIS 2 real-mode driver, click the down arrow under 
    Driver Type and select Real Mode NDIS Driver. Then click OK.

10. The Network Setup screen now lists the 3Com TokenLink Velocity ISA
    NIC (3C319) (NDIS2) along with the default protocol stacks.

11.  The Windows Setup now asks whether you want to replace the Enhanced
     Mode Protocol Manager with the version you are installing now. 
     Click Yes to All.

12.  The Windows setup program now asks for the NDIS.386 file. Insert
     Microsoft Windows for Workgroups 3.11 Disk 7 and click OK.

13.  When prompted for the TLNK3.DOS driver, insert the 3Com TokenDisk 
     diskette in the A: drive. To load the NDIS 2 driver, type this path:

     A:\NDIS2\DOS

     Click OK. 

14.  The PROTOCOL.INI and SYSTEM.INI files have now been modified.  WFW
     saves the old versions with the extension .001, where the number is
     incremented every time a new PROTOCOL.INI or SYSTEM.INI FILE is 
     generated. Click OK.

15.  Restart your system when prompted.

NOTE: The TokenLink NIC uses areas of upper memory to transfer data.  The
      Windows memory manager (EMM386) uses the same areas of upper memory.
      To reserve the required areas of upper memory for use by the NIC,
      add the eXclude parameter to the EMM386 device statement in the
      CONFIG.SYS file.  The following example assumes the NIC is 
      configured to the default shared RAM and BIOS/MMIO base addresses:

      DEVICE=C:\WINDOWS\EMM386.EXE NOEMS X=D800-DBFF X=CC00-CDFF

                                 



  (%VER WFWNDIS2.TXT - 2.01 Drivers and Windows for Workgroups 3.11 v1.0b)