1. 3c319.zip Driver
2. W95NDIS2.TXT File Contents

W95NDIS2.TXT Driver File Contents (3c319.zip)

                        3Com (R) Corporation
                     TokenDisk (R) Diskette for
  The 3C319 TokenLink Velocity ISA Token Ring Network Interface Card
                    NDIS 2 Driver and Windows 95


Initial Installation
--------------------

NOTE: 3Com recommends that you use the NDIS 3 driver with Windows 95. The  
      NDIS 2 driver is only a 16-bit driver.  Your system performance       
      will be maximized if you use the NDIS 3 driver instead.

Before you install the NDIS 2 driver on a computer running Windows 95, make
sure the NIC has been properly installed and that the NIC has passed the 
configuration and diagnostic procedure.

NOTE: If the NIC fails the configuration and diagnostic tests, look for 
      troubleshooting information in the TROUBLE.TXT file in the HELP 
      directory on the 3Com TokenDisk diskette.

1.  Turn on the computer and start Windows 95.  A message appears, 
    informing you that Windows 95 is detecting new hardware and is looking
    for the drivers.

2.  If you are installing this NIC for the first time, you will be 
    prompted to install the driver from a diskette provided by the hardware
    manufacturer.

3.  Insert the 3Com TokenDisk diskette and click OK.

4.  Specify the letter of the floppy drive location.  For example, if your 
    floppy drive is drive A:, type:

    A:\ [Enter]

    Then click OK.

5.  Windows 95 will read in the W95TLNKV.INF file.

6.  Select the appropriate NIC.

7.  Go to Network on the Control Panel, and click once on the NIC name.

8.  In the Driver Type tab, click on Properties, and then on Real Mode 
    (16 bit) NDIS Driver. 

9.  Click on OK.  You are prompted to restart your computer.

10. Installation is now complete.


Updating the Driver
--------------------
1.  After installing the NIC in the ISA or EISA slot and connecting the 
    cables to the network, turn on the computer and start Windows 95.
 
2.  Click Start, then Settings.  Then select Control Panel.

3.  In the Control Panel, click Network and then highlight the name of the 
    NIC.
    
4.  Click Remove, then OK. You will be prompted to restart your computer.

5.  Repeat step 2.

6.  In the Control Panel, click Network, then Add.

7.  Select Adapters, then 3COM.

8.  Click Have Disk.  Then insert the 3Com TokenDisk diskette into the 
    appropriate floppy drive.

9.  Specify the letter of the floppy drive location.  For example, if your 
    floppy drive is drive A, type: 

    A:\ [Enter]

    Then click OK.

    HINT: If an error message appears, saying that the .INF file cannot be 
          found in the specified location, verify that the file actually 
          exists.  The file should be located in the root directory of the 
          3Com TokenDisk diskette.  The filename is W95TLNKV.INF.

10. Select the correct NIC from the list and then click OK. 

11. Select the NIC again and click Properties.

12. In the Driver Type tab click Real Mode (16 bit) NDIS Driver.

13. Click OK.

14. Click Restart Computer.


Verifying Driver Installation
-----------------------------
1.  In Windows 95, click Start, Settings, and then Control Panel.

2.  Select Network and then select the NIC in the configuration box 
    and click Properties.

3.  In the Driver Type tab, verify that the item below is selected:

    Real Mode (16 bit) NDIS Driver

        
             (%VER W95NDIS2.TXT - NDIS 2 in Windows 95 v1.0b)