;*********************************************************************** ; ; OEMSETUP.INF ; ; IEEE802.11b WLAN Card ; Copyright (C) 2002, All rights reserved. ; ;*********************************************************************** ;*********************************************************************** ; 1. Identify ; ; DESCRIPTION: To verify that this INF deals with the same type of options ; as we are choosing currently. ; ; INPUT: None ; ; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL ; $($R1): Option Type (COMPUTER ...) ; $($R2): Diskette description ;*********************************************************************** ; ; ;--------------------------------------------------------------------------- ; OPTION TYPE ; ----------- ; This identifies the Option type we are dealing with. The different ; possible types are: ; ; COMPUTER, DISPLAY, MOUSE, KEYBOARD, LAYOUT, SCSI, PRINTER, ... ; ; Types specific to networking: ; ; NetAdapter, a netcard / adapter combination or just a netcard ; NetDriver, just a netcard driver ; NetTransport, a complete NDIS-compliant TDI transport stack ; NetService, an NT networking service ; NetWork, a complete network ensemble. ; NetProvider a complete network which supports NT MPR protocol ;--------------------------------------------------------------------------- [Identify] set Status = STATUS_SUCCESSFUL set Identifier = NetAdapter set Media = #("Source Media Descriptions", 1, 1) Return $(Status) $(Identifier) $(Media) ;*********************************************************************** ; ; End Indentify ; ;*********************************************************************** ;*********************************************************************** ; 2. ReturnOptions: ; ; DESCRIPTION: To return the option list supported by this INF and the ; localised text list representing the options. ; ; ; INPUT: $($0): Language used. ( ENG | FRN | ... ) ; ; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL | ; STATUS_NOLANGUAGE ; STATUS_FAILED ; STATUS_NOTSUPPORTED ; ; $($R1): Option List ; $($R2): Option Text List ;*********************************************************************** [ReturnOptions] ; ; set Status = STATUS_FAILED set OptionList = {} set OptionTextList = {} ; ; Check if the language requested is supported ; set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) in $(LanguageList) ; ; Check if the platforms requested is supported ; ifstr(i) $($1) == "" goto returnoptions endif set PlatformList = ^(PlatformsSupported, 1) Ifcontains(i) $($1) in $(PlatformList) goto returnoptions else set Status = STATUS_NOTSUPPORTED goto finish_ReturnOptions endif else set Status = STATUS_NOLANGUAGE goto finish_ReturnOptions endif ; ; form a list of all the options and another of the text representing ; returnoptions = + set OptionList = ^(Options, 1) set OptionTextList = ^(OptionsText$($0), 1) set Status = STATUS_SUCCESSFUL finish_ReturnOptions = + Return $(Status) $(OptionList) $(OptionTextList) ;======================================================================= ; ; ReturnOptions related symbols ; ;======================================================================= ;----------------------------------------------------------------------- ; PlatformsSupported ; ------------------ ; This identifies the platforms supported by the adapter card. ; Possible types are: ; ; ISA, EISA, MCA and PCMCIA ;----------------------------------------------------------------------- [PlatformsSupported] ISA PCMCIA ;----------------------------------------------------------------------- ; ; Languages Supported in INF File ; Possible types are: ; ; ENG, FRN, SPN, ... ;----------------------------------------------------------------------- [LanguagesSupported] ENG ;----------------------------------------------------------------------- ; OPTION LIST ; ----------- ; This section lists the OEM Option key names. These keys are locale ; independent and used to represent the option in a locale independent ; manner. ; ;----------------------------------------------------------------------- [Options] PRISM2_5_PCMCIA [OptionsTextENG] PRISM2_5_PCMCIA ="IEEE802.11b WLAN Card" ;*********************************************************************** ; ; End ReturnOptions ; ;*********************************************************************** ;*********************************************************************** ; 4. Source Media Descriptions: ; ; DESCRIPTION: A detect section required in all oemsetup.inf files. It ; consists of a lied for each floppy disk that is part of ; the distribution set. The format is as follows: ; ; LineKey = [DiskDescription, TAGFILE = TagFileName] ; ; EXAMPLE: 1 = "Driver Disk #1", TAGFILE = disk1 ; ; ; INPUT: None ; ; OUTPUT: None ; ;*********************************************************************** [Source Media Descriptions] 1 = "IEEE802.11b WLAN Card driver Disc" ;*********************************************************************** ; ; End Source Media Descriptions ; ;*********************************************************************** ;*********************************************************************** ; ; InstallOption: ; ; This section is shelled to by main installation processing ; or by NCPASHEL.INF during reconfig, removal, update, etc. ; ; ; FUNCTION: To copy files representing Options ; To configure the installed option ; To update the registry for the installed option ; ; INPUT: $($0): Language to use ; $($1): OptionID to install ; $($2): SourceDirectory ; $($3): AddCopy (YES | NO) ; $($4): DoCopy (YES | NO) ; $($5): DoConfig (YES | NO) ; ; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL | ; STATUS_NOLANGUAGE | ; STATUS_USERCANCEL | ; STATUS_FAILED ; ;*********************************************************************** ;------------------------------------------------------------------------ ; CONSTANTS FOR USING DIALOGS ;------------------------------------------------------------------------ [IntersilPrism25FileConstants] GenericAdapterName = "IEEE802.11b WLAN Card" [FileConstants] GenericDriverName = "IEEE802.11b WLAN Card Client driver" GenericSysName = "WLPCND4.sys" GenericName = "WLPC" lowercaseName = "wlpc" ; ; File names, etc. ; UtilityInf = "UTILITY.INF" ParamInf = "NCPARAM.INF" subroutineinf = "SUBROUTN.INF" SoftwareType = "driver" Exit_Code = 0 ; ; EventLog Message File ; NetEventDLL = "%SystemRoot%\System32\netevent.dll" IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll" ; ; Product Info ; Manufacturer = "Wireless Manufacturer" ProductMajorVersion = "2" ProductMinorVersion = "0" VER_PRODUCT_MAJOR_STR = "2" VER_PRODUCT_MINOR_STR = "0" VER_PRODUCT_SUB_MINOR_STR = "9" ProductVersion = $(VER_PRODUCT_MAJOR_STR)"."$(VER_PRODUCT_MINOR_STR)"."$(VER_PRODUCT_SUB_MINOR_STR) DriverVersion = $(VER_PRODUCT_MAJOR_STR)"."$(VER_PRODUCT_MINOR_STR)"."$(VER_PRODUCT_SUB_MINOR_STR) ; ; Software ; ProductSoftwareName = $(GenericName) ProductSoftwareImagePath = "\SystemRoot\System32\drivers\"$(GenericSysName) NetRuleSoftwareType = $(lowercaseName)"Sys ndisDriver "$(lowercaseName)"Driver" NetRuleSoftwareUse = $(SoftwareType) NetRuleSoftwareBindForm = """"$(lowercaseName)"Sys"" yes no container" NetRuleSoftwareClass = {$(lowercaseName)"Driver basic"} NetRuleSoftwareBindable = {$(lowercaseName)"Driver "$(lowercaseName)"Adapter non exclusive 100"} ; ; Hardware ; ProductHardwareName = $(GenericName) NetRuleHardwareType = $(lowercaseName)" "$(lowercaseName)"Adapter" NetRuleHardwareBindForm = " yes yes container" NetRuleHardwareClass = {$(lowercaseName)"Adapter basic"} ; ; Registry Key ; ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion" ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters" PcmciaDataBaseKeyName = $(!NTN_ServiceBase)"\Pcmcia\Database" DialogDllName = "WLPC.dll" [GeneralConstants] ; ; Program flow control variables. ; from = "" to = "" ; ; Return codes; Exit_Code is set to one of these ; ExitCodeOk = 0 ExitCodeCancel = 1 ExitCodeFatal = 2 KeyNull = "" MAXIMUM_ALLOWED = 33554432 RegistryErrorIndex = NO_ERROR KeyProduct = "" KeyParameters = "" TRUE = 1 FALSE = 0 NoTitle = 0 ExitState = "Active" OldVersionExisted = $(FALSE) DriverPath = $(!STF_NTPATH)\drivers [date] ; Now is a list which contains { Sec from 1-1-1970, Year, Month, Day, Hour, ; Minute, Second } Now = {} ? $(!LIBHANDLE) GetSystemDate ;------------------------------------------------------------------------ ; ; InstallOption: ; ; This section is shelled to by main installation processing ; or by NCPASHEL.INF during reconfig, removal, update, etc. ; ; ; FUNCTION: To copy files representing Options ; To configure the installed option ; To update the registry for the installed option ; ; INPUT: $($0): Language to use ; $($1): OptionID to install ; $($2): SourceDirectory ; $($3): AddCopy (YES | NO) ; $($4): DoCopy (YES | NO) ; $($5): DoConfig (YES | NO) ; ; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL | ; STATUS_NOLANGUAGE | ; STATUS_USERCANCEL | ; STATUS_FAILED ; ;------------------------------------------------------------------------ [InstallOption] ; ; Set default values for ; set Status = STATUS_FAILED ; ; extract parameters ; set Option = $($1) set SrcDir = $($2) set AddCopy = $($3) set DoCopy = $($4) set DoConfig = $($5) ; Enable debugging output Set !G:DebugOutputControl = 1 ; ; Check if the language requested is supported ; set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) NOT-IN $(LanguageList) Return STATUS_NOLANGUAGE endif read-syms GeneralConstants read-syms IntersilPrism25FileConstants read-syms FileConstants read-syms DialogConstants$(!STF_LANGUAGE) ifstr(i) $(!NTN_Origination) == "NCPA" set Continue = $(OK) endif read-syms FileConstants$(!STF_LANGUAGE) detect date set-title $(FunctionTitle) set to = Begin set from = Begin ; ; Assume all is well. ; set CommonStatus = STATUS_SUCCESSFUL EndWait ; ; Set up the operation-mode-based variables and gaily welcome ; the user. If the "install mode" variable is improperly set, ; assume this is a new installation. ; Begin = + Set ActivateDetection = FALSE Ifstr(i) $(!NTN_InstallMode) == deinstall set StartLabel = removeadapter else-Ifstr(i) $(!NTN_InstallMode) == Update set StartLabel = UpgradeSoftware else-Ifstr(i) $(!NTN_InstallMode) == bind set StartLabel = bindingadapter else-Ifstr(i) $(!NTN_InstallMode) == configure ; set ActivateDetection = TRUE set StartLabel = configureadapter ; ; You cannot config the software component ; Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) Debug-Output "Cannot configure the PRISM II driver." Shell $(UtilityInf), RegistryErrorString, "CANNOT_CONFIGURE_SOFTWARE" ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." goto ShellCodeError endif set Error = $($R0) set from = end set to = end goto nonfatalinfo endif else ; set ActivateDetection = TRUE set StartLabel = installadapter set OEM_ABANDON_OPTIONS = {} set OEM_ABANDON_SOFTWARE = FALSE set OEM_ABANDON_ON = TRUE endif install "PCMCIA-Defaults" install "Read-Defaults" install "Parm-WriteReg" Set from = $(fatal) Set to = $(fatal) Goto $(StartLabel) ;----------------------------------------------- ; Installation Section ;----------------------------------------------- installadapter = + ; ; Create/recreate the Registry's PCMCIA database entry for the CW10 adapter ; Debug-Output "*** installadapter ***" Debug-Output "PcmciaDataBaseKeyName = "$(PcmciaDataBaseKeyName) set ManKeyName = "PCMCIA\11M WLAN Card v2.5" set ManKeyName1 = "PCMCIA\11M WLAN Card v2.5" set ManKeyName2 = "PCMCIA\11M WLAN Card v3.0" set ManKeyName3 = "PCMCIA\11M WLAN Card v3.0" Debug-Output "ManKeyName = "$(ManKeyName) set KeyPcmciaDataBase = "" OpenRegKey $(!REG_H_LOCAL) "" $(PcmciaDataBaseKeyName) $(MAXIMUM_ALLOWED) KeyPcmciaDataBase Shell "" ExCreateRegKey $(KeyPcmciaDataBase) $(ManKeyName) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." CloseRegKey $(KeyPcmciaDataBase) goto ShellCodeError endif OpenRegKey $(KeyPcmciaDataBase) "" $(ManKeyName) $(MAXIMUM_ALLOWED) KeyTemp SetRegValue $(KeyTemp) {Driver,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)} SetRegValue $(KeyTemp) {DeviceType,$(NoTitle),$(!REG_VT_SZ),"NET"} CloseRegKey $(KeyTemp) Shell "" ExCreateRegKey $(KeyPcmciaDataBase) $(ManKeyName1) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." CloseRegKey $(KeyPcmciaDataBase) goto ShellCodeError endif OpenRegKey $(KeyPcmciaDataBase) "" $(ManKeyName1) $(MAXIMUM_ALLOWED) KeyTemp SetRegValue $(KeyTemp) {Driver,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)} SetRegValue $(KeyTemp) {DeviceType,$(NoTitle),$(!REG_VT_SZ),"NET"} CloseRegKey $(KeyTemp) Shell "" ExCreateRegKey $(KeyPcmciaDataBase) $(ManKeyName2) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." CloseRegKey $(KeyPcmciaDataBase) goto ShellCodeError endif OpenRegKey $(KeyPcmciaDataBase) "" $(ManKeyName2) $(MAXIMUM_ALLOWED) KeyTemp SetRegValue $(KeyTemp) {Driver,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)} SetRegValue $(KeyTemp) {DeviceType,$(NoTitle),$(!REG_VT_SZ),"NET"} CloseRegKey $(KeyTemp) Shell "" ExCreateRegKey $(KeyPcmciaDataBase) $(ManKeyName3) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." CloseRegKey $(KeyPcmciaDataBase) goto ShellCodeError endif OpenRegKey $(KeyPcmciaDataBase) "" $(ManKeyName3) $(MAXIMUM_ALLOWED) KeyTemp SetRegValue $(KeyTemp) {Driver,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)} SetRegValue $(KeyTemp) {DeviceType,$(NoTitle),$(!REG_VT_SZ),"NET"} CloseRegKey $(KeyTemp) CloseRegKey $(KeyPcmciaDataBase) Debug-Output "Driver Value set in ManKey" ; ; Check whether the same version of the software exists ; OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) ; ; Same version already existed in the local machine ; Popup the dialog and ask the user whether he wants to continue ; Debug-Output "ProductKeyName already exists = "$(ProductKeyName) CloseRegKey $(KeyProduct) ifstr(i) !(NTN_RegBase) == $(ProductKeyName) Debug-Output "Cannot Install the same software again" Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+ $(ProductVersion) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." goto ShellCodeError endif goto end else Debug-Output "Add a new adapter card?" Shell $(UtilityInf), CardExistedDlg ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." goto ShellCodeError endif ifstr(i) $($R1) != "OK" goto end endif set OldVersionExisted = $(TRUE) endif endif ; ; dll load addition ; Debug-Output "Calling DoAskSource." Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) NO Ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." Goto ShellCodeError Else-Ifstr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." goto ShellCodeError endif set Error = $($R0) Goto fatal Else-Ifstr(i) $($R0) == STATUS_USERCANCEL Goto successful Endif Set SrcDir = $($R1) Debug-Output "Done DoAskSource, calling Install-Dll." ; ; Run Dll for updating parameters ; install "Install-Dll" Debug-Output "Done Install-Dll, going to adaptersetup." ; ; Create a registry entry to install utility after reboot ; OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows\CurrentVersion\run" $(MAXIMUM_ALLOWED) KeyRun Ifstr(i) $(KeyRun) != "" SetRegValue $(KeyRun) {WLPC, 0, $(!REG_VT_SZ), "rundll32 checkdll.dll,RunSetup"} CloseRegKey $(KeyRun) Endif ; Don't want to show Advance properties during install. ; goto adaptersetup goto skipoptions ;----------------------------------------------- ; Configuration Section ;----------------------------------------------- ; ; Get the current values of all the parameters ; configureadapter = + Debug-Output "Starting configureadapter." Ifstr $(KeyProduct) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output "Cannot find component product key" goto fatalregistry Endif Endif ; ; Get the other parameters; they're attached to the service parameters key ; Debug-Output "INF: Shelling to FindService" Shell $(UtilityInf) FindService, $(KeyProduct) Ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "INF: FindService shell failure" Goto ShellCodeError Endif Ifstr(i) $($R0) != NO_ERROR Debug-Output "INF: FindService Shell error: "$($R0) Goto fatalregistry endif Set KeyParameters = $($R2) ; ; We don't need the services key, so close it. ; CloseRegKey $($R1) Ifstr $(KeyParameters) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output "Cannot find component service" goto fatalregistry endif set OldVersionExisted = $(TRUE) install "Parm-ReadReg" ; Shell $(ParamInf) Param_SaveValues ; Set CurrParamSettings = $($R0) ; ; Put up the adapter configuration dialog if necessary. ; ; Note that $(CurrParamSettings) has the old known parameter values. ; adaptersetup = + ; Shell "" DebugConfiguration "before displaying dialog" Debug-Output "Starting adaptersetup" Set from = adapteroptions adapteroptions = + Debug-Output "Starting adapteroptions" LoadLibrary "Disk 1" $(!STF_WINDOWSSYSPATH)\$(DialogDllName) hLib read-syms FileDependentDlg$(!STF_LANGUAGE) ui start "InputDlg" $(hLib) set ExitButton = $(ButtonPressed) Debug-Output " ButtonPressed "$(ButtonPressed) FreeLibrary $(hLib) ifstr(i) $(DLGEVENT) == "CONTINUE" Debug-Output "Action: Continue" install "Parm-UI-values" set ExitButton = $(ButtonPressed) ui pop 1 ; goto nextstep else-ifstr(i) $(DLGEVENT) == "EXIT" set CommonStatus = STATUS_USERCANCEL Debug-Output "Action: exit. Bye." ui pop 1 goto end else ; ; Unknow command ; ui pop 1 Debug-Output "Action: unknown. Bye." goto end endif Debug-Output " Combo list out "$(ComboListItemsOut) ; ; If installing, go create the necessary keys; ; if configuring, they're already open. ; skipoptions =+ Debug-Output "Starting skipoptions." ifint $(OldVersionExisted) == $(TRUE) Debug-Output "Older version existed." ifstr(i) $(!NTN_InstallMode) == configure goto writeparameters endif endif StartWait ; ; Add Software Component ; ifint $(OldVersionExisted) == $(FALSE) Debug-Output "No older version." ifstr(i) $(!NTN_InstallMode) == "install" Ifstr(i) $(DoCopy) == "YES" Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Else-Ifstr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal Else-Ifstr(i) $($R0) == STATUS_USERCANCEL Goto successful Endif Set SrcDir = $($R1) Endif install "Install-Option" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal endif endif Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), + $(ProductSoftwareName), + $(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), + $(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+ $(NetEventDLL) Set OEM_ABANDON_SOFTWARE = TRUE ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif ; ; At this point: ; $R1 contains the product version key handle; ; $R2 contains the NetRules subkey handle; ; $R3 contains the new Services key handle; and ; $R4 contains the Parameters key ; $R5 contains the Linkage Key ; set RegistryErrorIndex = $($R0) set KeyProduct = $($R1) Set SoftNetRulesKey = $($R2) CloseRegKey $($R3) CloseRegKey $($R4) CloseRegKey $($R5) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add software components" CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) goto fatalregistry endif set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+ {MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+ {MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+ {Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add value list." CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) goto fatalregistry endif set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+ {use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, + {bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, + {bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareBindable)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(SoftNetRulesKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Resgitry error: add value list." goto fatalregistry endif endif ; ; Create the HARDWARE\Netcard region and its corresponding service ; Debug-Output "Calling AddHardwareComponent." Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName) ifint $($R4) != -1 Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4)) endif ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "Cannot add hardware component" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add hardware component" CloseRegKey $($R1) CloseRegKey $($R2) CloseRegKey $($R3) goto fatalregistry endif ; ; At this point: ; $R1 Registry key variable for HARDWARE\Netcard\(n) ; $R2 Registry key variable for HARDWARE\Netcard\(n)\\NetRules ; $R3 Registry key handle for <service>\Parameters key ; $R4 Adapter number assigned to adapter ; $R5 Service name generated by combining svc name with adapter number ; set KeyParameters = $($R3) set KeyAdapterRules = $($R2) set AdapterNumber = $($R4) set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+ {Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardwareTitle)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareDescription)},+ {ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $($R1), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif CloseRegKey $($R1) set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)"""" set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm) set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardwareType)},+ {bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardwareClass)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(KeyAdapterRules), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Resgitry error: add value list." CloseRegKey $(KeyParameters) CloseRegKey $(KeyAdapterRules) goto fatalregistry endif CloseRegKey $(KeyAdapterRules) ; ; Only create Defaults key when installing driver ; Write defaults to registry before updating values in lists ; Debug-Output "Starting Install-Defaults." CreateRegKey $(KeyParameters) {"defaults",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" DefaultsKey Ifstr(i) $(DefaultsKey) == $(KeyNull) Debug-Output "Registry error: Create defaults subkey" CloseRegKey $(KeyParameters) goto fatalregistry Endif Debug-Output "CreateKey successful." Shell $(UtilityInf), AddValueList, $(DefaultsKey), $(PRISMValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR Debug-Output "Registry error: Add value list" CloseRegKey $(DefaultsKey) CloseRegKey $(KeyParameters) goto fatalregistry endif Debug-Output "Adding PRISM defaults successful." Shell $(UtilityInf), AddValueList, $(DefaultsKey), $(NetTypeValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR Debug-Output "Registry error: Add value list" CloseRegKey $(DefaultsKey) CloseRegKey $(KeyParameters) goto fatalregistry endif Debug-Output "Adding defaults based on NetworkType, successful." Shell $(UtilityInf), AddValueList, $(DefaultsKey), $(PHYTypeValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR Debug-Output "Registry error: Add value list" CloseRegKey $(DefaultsKey) CloseRegKey $(KeyParameters) goto fatalregistry endif Debug-Output "Adding defaults based on PHYType, successful." goto writeparameters ; ; REQUIRED: $(KeyParameters) contains service Parameters key handle ; writeparameters = + Debug-Output "Starting writeparameters." Shell $(UtilityInf), GetBusTypeNum ; set BusTypeNum = $($R1) ; the above was not working so hard coding the bus type to 1 which represents ; NdisInterfaceIsa set BusTypeNum = 1 set BusNumber = 0 ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif ; ; Add the rest of the parameters to the Services area ; install "Parm-WriteReg" Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NetValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR Debug-Output "Registry error: Add value list" CloseRegKey $(KeyParameters) goto fatalregistry endif Shell $(UtilityInf), AddValueList, $(KeyParameters), $(PRISMValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR Debug-Output "Registry error: Add value list" CloseRegKey $(KeyParameters) goto fatalregistry endif Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NetTypeValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR Debug-Output "Registry error: Add value list" CloseRegKey $(KeyParameters) goto fatalregistry endif Shell $(UtilityInf), AddValueList, $(KeyParameters), $(PHYTypeValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR Debug-Output "Registry error: Add value list" CloseRegKey $(KeyParameters) goto fatalregistry endif CloseRegKey $(KeyParameters) EndWait goto successful ;----------------------------------------------- ; Binding section ;----------------------------------------------- bindingadapter =+ set Error = "Binding: Sorry, not yet implemented." goto fatal ;----------------------------------------------- ; Removeadapter section ;----------------------------------------------- removeadapter = + Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) ; Remove Software Component Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif else Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $(!NTN_RegBase) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif goto end ;----------------------------------------------- ; Upgrade Software section ;----------------------------------------------- UpgradeSoftware = + ; ; First determine whether we want to do upgrade or update for software ; or hardware component. Then we will determine whether the Mode is ; update or upgrade. ; ; If the same version of the product existed in the registry, we do ; update. Otherwise, we will do a upgrade ; ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) ; Upgrade software component ; ; see whether the same version exist or not ; OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) GetRegValue $(KeyProduct),"MajorVersion", VersionInfo set Version = *($(VersionInfo), 4) ; ; Update the binaries ; Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set !UG_Filename = $($R0) ifstr(i) $(!UG_Filename) != "" install "Install-Update" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS goto fatal endif endif ; Upgrade the version number ; SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)} SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)} ; ; do nothing for update ; ifint $(Version) != $(ProductVersion) ; ; If the major version number is not the same, ; it is major upgrade. So let Upgrade the product ; ; ; make other upgrade change if necessary ; endif CloseRegKey $(KeyProduct) else ; ; Cannot Open software key, goto ERROR ; goto fatalregistry endif else ; ; upgrade/update hardware component ; There is no different between upgrade and update for hardware ; component ; ; 1. Get the Service Name ; 2. Change the NetRule section if necessary ; OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) + $(MAXIMUM_ALLOWED) NetworkCardKey Ifstr(i) $(NetworkCardKey) != $(KeyNull) ; ; Get Service name ; GetRegValue $(NetworkCardKey),"ServiceName", ServiceNameInfo set ServiceName = *($(ServiceNameInfo), 4) ; ; Change the NetRule if necessary ; OpenRegKey $(NetworkCardKey) "" "NetRules" + $(MAXIMUM_ALLOWED) NetRuleKey Ifstr(i) $(NetRuleKey) != $(KeyNull) ; ; Make the change.... ; else ; ; Error, cannot open net rules key ; goto fatalregistry endif CloseRegKey $(NetRules) CloseRegKey $(NetworkCardKey) else ; ; Error, cannot open network card key ; goto fatalregistry endif ; ; 3. Change the service section of the hardware. i.e., ; ParameterName change, value change, etc. ; OpenRegKey $(!REG_H_LOCAL) "" + $(!NTN_ServiceBase)"\"$(ServiceName) + $(MAXIMUM_ALLOWED) ServiceKey Ifstr(i) $(ServiceKey) != $(KeyNull) ; ; Get the ServiceKey to change the Start value ; or Type value. Or open Parameters key to ; change the hardware parameters if necessary. ; CloseRegKey $(ServiceKey) else ; ; Error, cannot open network card key ; goto fatalregistry endif endif goto end ; ; End of Upgrade Software ; ; ; Escape hatches ; successful = + goto end abandon = + ForListDo $(OEM_ABANDON_OPTIONS) Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $($) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif EndForListDo Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE ; Remove Software Component Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), FALSE ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif goto end ; ; warning display ; warning = + Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(to) else-ifstr(i) $($R1) == "CANCEL" goto $(from) else goto "end" endif ; ; non fatal error display ; nonfatalinfo = + Set Severity = STATUS Set CommonStatus = STATUS_USERCANCEL goto nonfatalmsg nonfatal = + Set Severity = NONFATAL goto nonfatalmsg nonfatalmsg = + ifstr(i) $(Error) == "" Set Severity = NONFATAL Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(from) else goto "end" endif ; ; Registry is broken ; fatalregistry = + Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal ; ; Netcard detection failure ; fataldetect = + Shell $(UtilityInf), RegistryErrorString, "CANNOT_DETECT" ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." goto ShellCodeError endif set Error = $($R0) Goto fatal ; ; fatal error display ; fatal = + ifstr(i) $(Error) == "" Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif goto setfailed ; ; Shelling error ; ShellCodeError = + set DlgType = "MessageBox" set STF_MB_TITLE = $(ShellCodeErrorTitle) set STF_MB_TEXT = $(ShellCodeErrorText) set STF_MB_TYPE = 1 set STF_MB_ICON = 3 set STF_MB_DEF = 1 ui start "Error Message" goto setfailed setfailed = + set CommonStatus = STATUS_FAILED ; ; if OEM_ABANDON_ON == TRUE, then remove the registry entries ; ifstr(i) $(OEM_ABANDON_ON) == TRUE set OEM_ABANDON_ON = FALSE goto abandon endif goto end end = + goto term term = + Return $(CommonStatus) [DebugConfiguration] Set InfName = "OEMNANDC.INF" Debug-Output $(InfName)" **CONFIGURATION STATE: "$($0) Debug-Output $(InfName)" IRQ_Level is "$(!p:IRQ_Level) Debug-Output $(InfName)" IOBaseAddrValue is "$(!p:IOBaseAddrValue) Debug-Output $(InfName)" TransceiverValue is "$(!p:TransceiverValue) Debug-Output $(InfName)" MappedValue is "$(!p:MappedValue) return ;*************************************************************** ; INSTALL SECTIONS ;*************************************************************** [Install-Option] set STF_VITAL = "" ifstr(i) $(AddCopy) == "YES" ; ; Add the files to the copy list ; ; BUGBUG: eliminate the "nt2" in the next line when Sunil fixes ; the other INF files ; AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers AddSectionFilesToCopyList Files-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH) endif ifstr(i) $(DoCopy) == "YES" ; ; Copy files in the copy list ; set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList endif Exit [Install-Update] set STF_VITAL = "" set STF_OVERWRITE = "VERIFYSOURCEOLDER" ;set STF_VERSION = "YES" AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH) AddSectionFilesToCopyList Files-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH) set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList exit [Install-Dll] set STF_VITAL = "" AddSectionFilesToCopyList Files-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH) set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList exit ;*************************************************************** ; Parameter SECTIONS ;*************************************************************** [Parm-ReadReg] set ValueName = "" set ValueData = "" set ValueStr = "" set ValueList = {} ; ; Get the old values ; EnumRegValue $(KeyParameters) ValueList ForListDo $(ValueList) set ValueItem = $($) set ValueName = *($(ValueItem),1) set ValueData = *($(ValueItem),4) ; resources ifstr(i) $(ValueName) == "IoBaseAddress" set IOBaseAddrItem = $(ValueData) else-ifstr(i) $(ValueName) == "InterruptNumber" set IRQValueItem = $(ValueData) ; general - combo else-ifstr(i) $(ValueName) == "DSChannel" set PHYParmItem = $(ValueData) else-ifstr(i) $(ValueName) == "NetworkType" set NetTypeItem = $(ValueData) else-ifstr(i) $(ValueName) == "TxRate" set TxRateItem = $(ValueData) else-ifstr(i) $(ValueName) == "AuthentAlg" set AuthenticationItem = $(ValueData) else-ifstr(i) $(ValueName) == "ListenInterval" set ListenIntervalItem = $(ValueData) else-ifstr(i) $(ValueName) == "RTSThresh" set RTSThreshItem = $(ValueData) else-ifstr(i) $(ValueName) == "FragThresh" set FragThreshItem = $(ValueData) else-ifstr(i) $(ValueName) == "PSMode" set PSModeItem = $(ValueData) else-ifstr(i) $(ValueName) == "WepReq" set WepReqItem = $(ValueData) ; checkbox else-ifstr(i) $(ValueName) == "Pcmcia" set PcmciaValue = $(ValueData) ; edit else-ifstr(i) $(ValueName) == "SSID" set SSIDValue = $(ValueData) endif EndForListDo ifint $(PcmciaValue) == 1 set Chk1 = "ON" else set Chk1 = "OFF" endif set IOBaseAddrUIVal = *($(IOBaseAddrList), ~($(IOBaseAddrValues),$(IOBaseAddrItem))) ifstr(i) $(IOBaseAddrUIVal) == "" set IOBaseAddrUIVal = *($(IOBaseAddrList), 1) endif set IRQValueUIVal = *($(IRQList), ~($(IRQValues),$(IRQValueItem))) ifstr(i) $(IRQValueUIVal) == "" set IRQValueUIVal = *($(IRQList), 1) endif set PHYParmUIVal = *($(PHYParmList), ~($(PHYParmValues),$(PHYParmItem))) ifstr(i) $(PHYParmUIVal) == "" set PHYParmUIVal = *($(PHYParmList), 1) endif set NetTypeUIVal = *($(NetTypeList), ~($(NetTypeValues),$(NetTypeItem))) ifstr(i) $(NetTypeUIVal) == "" set NetTypeUIVal = *($(NetTypeList), 1) endif set TxRateUIVal = *($(TxRateList), ~($(TxRateValues),$(TxRateItem))) ifstr(i) $(TxRateUIVal) == "" set TxRateUIVal = *($(TxRateList), 1) endif set AuthenticationUIVal = *($(AuthenticationList), ~($(AuthenticationValues),$(AuthenticationItem))) ifstr(i) $(AuthenticationUIVal) == "" set AuthenticationUIVal = *($(AuthenticationList), 1) endif set ListenIntervalUIVal = *($(ListenIntervalList), ~($(ListenIntervalValues),$(ListenIntervalItem))) ifstr(i) $(ListenIntervalUIVal) == "" set ListenIntervalUIVal = *($(ListenIntervalList), 6) endif set RTSThreshUIVal = *($(RTSThreshList), ~($(RTSThreshValues),$(RTSThreshItem))) ifstr(i) $(RTSThreshUIVal) == "" set RTSThreshUIVal = *($(RTSThreshList), 6) endif set FragThreshUIVal = *($(FragThreshList), ~($(FragThreshValues),$(FragThreshItem))) ifstr(i) $(FragThreshUIVal) == "" set FragThreshUIVal = *($(FragThreshList), 6) endif set PSModeUIVal = *($(PSModeList), ~($(PSModeValues),$(PSModeItem))) ifstr(i) $(PSModeUIVal) == "" set PSModeUIVal = *($(PSModeList), 1) endif set WepReqUIVal = *($(WepReqList), ~($(WepReqValues),$(WepReqItem))) ifstr(i) $(WepReqUIVal) == "" set WepReqUIVal = *($(WepReqList), 1) endif ; Save the settings as they were read from the Registry. exit [Parm-UI-values] set IOBaseAddrUIVal = $(Combo1Out) set IRQValueUIVal = $(Combo2Out) set TxRateUIVal = $(Combo3Out) set PHYParmUIVal = $(Combo4Out) set NetTypeUIVal = $(Combo5Out) set RTSThreshUIVal = $(Combo6Out) set FragThreshUIVal = $(Combo7Out) set PSModeUIVal = $(Combo8Out) set WepReqUIVal = $(Combo9Out) set AuthenticationUIVal = $(Combo10Out) set ListenIntervalUIVal = $(Combo11Out) set SSIDValue = *($(EditTextOut),1) Set Chk = *($(CheckItemsOut), 1) Ifstr(i) $(Chk) == "ON" Set PcmciaValue = 1 set Chk1 = "ON" Else Set PcmciaValue = 0 set Chk1 = "OFF" Endif exit [Parm-WriteReg] Debug-Output "Starting Parm-WriteReg." set IOBaseAddrValue = *($(IOBaseAddrValues), ~($(IOBaseAddrList),$(IOBaseAddrUIVal))) set IRQValue = *($(IRQValues), ~($(IRQList),$(IRQValueUIVal))) set PHYParmValue = *($(PHYParmValues), ~($(PHYParmList),$(PHYParmUIVal))) set NetTypeValue = *($(NetTypeValues), ~($(NetTypeList),$(NetTypeUIVal))) set TxRateValue = *($(TxRateValues), ~($(TxRateList),$(TxRateUIVal))) set AuthenticationValue = *($(AuthenticationValues), ~($(AuthenticationList),$(AuthenticationUIVal))) set ListenIntervalValue = *($(ListenIntervalValues), ~($(ListenIntervalList),$(ListenIntervalUIVal))) set RTSThreshValue = *($(RTSThreshValues), ~($(RTSThreshList),$(RTSThreshUIVal))) set FragThreshValue = *($(FragThreshValues), ~($(FragThreshList),$(FragThreshUIVal))) set PSModeValue = *($(PSModeValues), ~($(PSModeList),$(PSModeUIVal))) set WepReqValue = *($(WepReqValues), ~($(WepReqList),$(WepReqUIVal))) ifstr(i) $(IRQValueUIVal) == "n/a" ; ; If n/a then don't write InterruptNumber registry value. ; set NetValueList = {+ {MediaType, $(NoTitle),$(!REG_VT_DWORD),1},+ {BusNumber, $(NoTitle),$(!REG_VT_DWORD),$(BusNumber)},+ {BusType, $(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+ {IoBaseAddress, $(NoTitle),$(!REG_VT_DWORD),$(IOBaseAddrValue)},+ {IoLength, $(NoTitle),$(!REG_VT_DWORD),64},+ {Pcmcia, $(NoTitle),$(!REG_VT_DWORD),$(PcmciaValue)},+ {MajorVersion, $(NoTitle),$(!REG_VT_SZ),2},+ {MinorVersion, $(NoTitle),$(!REG_VT_SZ),0},+ } else set NetValueList = {+ {MediaType, $(NoTitle),$(!REG_VT_DWORD),1},+ {BusNumber, $(NoTitle),$(!REG_VT_DWORD),$(BusNumber)},+ {BusType, $(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+ {IoBaseAddress, $(NoTitle),$(!REG_VT_DWORD),$(IOBaseAddrValue)},+ {IoLength, $(NoTitle),$(!REG_VT_DWORD),64},+ {InterruptNumber,$(NoTitle),$(!REG_VT_DWORD),$(IRQValue)},+ {Pcmcia, $(NoTitle),$(!REG_VT_DWORD),$(PcmciaValue)},+ ; {MajorVersion, $(NoTitle),$(!REG_VT_SZ),2},+ ; {MinorVersion, $(NoTitle),$(!REG_VT_SZ),0},+ } endif set PRISMValueList = {+ {SSID, $(NoTitle),$(!REG_VT_SZ), $(SSIDValue)},+ {WEP64_KEY_1, $(NoTitle),$(!REG_VT_SZ), "0000000000"},+ {WEP64_KEY_2, $(NoTitle),$(!REG_VT_SZ), "0000000000"},+ {WEP64_KEY_3, $(NoTitle),$(!REG_VT_SZ), "0000000000"},+ {WEP64_KEY_4, $(NoTitle),$(!REG_VT_SZ), "0000000000"},+ {WEP128_KEY_1, $(NoTitle),$(!REG_VT_SZ), "00000000000000000000000000"},+ {WEP128_KEY_2, $(NoTitle),$(!REG_VT_SZ), "00000000000000000000000000"},+ {WEP128_KEY_3, $(NoTitle),$(!REG_VT_SZ), "00000000000000000000000000"},+ {WEP128_KEY_4, $(NoTitle),$(!REG_VT_SZ), "00000000000000000000000000"},+ {CurProfile, $(NoTitle),$(!REG_VT_SZ), "default"},+ {RTSThresh, $(NoTitle),$(!REG_VT_DWORD),$(RTSThreshValue)},+ {FragThresh, $(NoTitle),$(!REG_VT_DWORD),$(FragThreshValue)},+ ; {Encapsulation, $(NoTitle),$(!REG_VT_DWORD),$(EthConvValue)},+ {TxRate, $(NoTitle),$(!REG_VT_DWORD),$(TxRateValue)},+ {WepReq, $(NoTitle),$(!REG_VT_DWORD),$(WepReqValue)},+ {AuthentAlg, $(NoTitle),$(!REG_VT_DWORD),$(AuthenticationValue)},+ {ListenInterval,$(NoTitle),$(!REG_VT_DWORD),$(ListenIntervalValue)},+ ; {DecryptInDriver,$(NoTitle),$(!REG_VT_DWORD),$(DecryptInDriverValue)},+ ; {EncryptInDriver,$(NoTitle),$(!REG_VT_DWORD),$(EncryptInDriverValue)},+ ; {WEPFactor, $(NoTitle),$(!REG_VT_DWORD),$(WEPFactorValue)},+ ; {PollInDriver, $(NoTitle),$(!REG_VT_DWORD),$(PollInDriverValue)},+ ; {IBSSInDriver, $(NoTitle),$(!REG_VT_DWORD),$(IBSSInDriverValue)},+ {PreambleMode, $(NoTitle),$(!REG_VT_DWORD),$(PreambleModeValue)},+ } set NetTypeValueList = {+ {NetworkType, $(NoTitle),$(!REG_VT_DWORD),$(NetTypeValue)},+ {PSMode, $(NoTitle),$(!REG_VT_DWORD),$(PSModeValue)},+ ; {PSLevel, $(NoTitle),$(!REG_VT_DWORD),$(PSLevelValue)},+ } set PHYTypeValueList = {+ {DSChannel, $(NoTitle),$(!REG_VT_DWORD),$(PHYParmValue)},+ } ; Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList) exit ;*************************************************************** ; Symbol SECTIONS ;*************************************************************** [ProductType] STF_PRODUCT = Winnt STF_PLATFORM = I386 [Files-Inf] 1, oemsetup.inf, SIZE=40558, RENAME=$(!UG_Filename) [Files-PRISM2_5_PCMCIA] 1, WLPCND4.sys, SIZE=12800 [Files-Dll] 1, WLPC.dll , SIZE=7168 1, CheckDLL.dll , SIZE=7168 [FileConstantsENG] ProCaption = "Windows NT Setup" ProCancel = "Cancel" ProCancelMsg = "Windows NT Networking is not correctly installed. "+ "Are you sure you want to cancel copying files?" ProCancelCap = "Network Setup Message" ProText1 = "Copying:" ProText2 = "To:" FunctionTitle = $(GenericAdapterName)" Setup" ProductSoftwareDescription = $(GenericDriverName) ProductHardwareDescription = $(GenericAdapterName) ProductSoftwareTitle = $(GenericDriverName) ProductHardwareTitle = $(GenericAdapterName) DialogDllName = "WLPC.dll" IOBaseAddrList = ^(IOBaseAddrChoices, 1) IOBaseAddrValues = ^(IOBaseAddrChoices, 2) ; IRQList = ^(IRQChoices, 1) ; IRQValues = ^(IRQChoices, 2) DSChanList = ^(DSChanChoices, 1) DSChanValues = ^(DSChanChoices, 2) STA_NetTypeList = ^(STA_NetTypeChoices, 1) STA_NetTypeValues = ^(STA_NetTypeChoices, 2) STA_TxRateList = ^(STA_TxRateChoices, 1) STA_TxRateValues = ^(STA_TxRateChoices, 2) STA_AuthenticationList = ^(STA_AuthenticationChoices, 1) STA_AuthenticationValues= ^(STA_AuthenticationChoices, 2) STA_ListenIntervalList = ^(STA_ListenIntervalChoices, 1) STA_ListenIntervalValues= ^(STA_ListenIntervalChoices, 2) RTSThreshList = ^(RTSThreshChoices, 1) RTSThreshValues = ^(RTSThreshChoices, 2) FragThreshList = ^(FragThreshChoices, 1) FragThreshValues = ^(FragThreshChoices, 2) STA_PSModeList = ^(STA_PSModeChoices, 1) STA_PSModeValues = ^(STA_PSModeChoices, 2) WepReqList = ^(WepReqChoices, 1) WepReqValues = ^(WepReqChoices, 2) [DialogConstantsENG] Help = "&Help" Exit = "Cancel" OK = "OK" HelpContext = "" Continue = "Continue" Cancel = "Cancel" ;[MemoryMappedChoicesENG] ; Map_1 = 1, "ON" ; Map_2 = 0, "OFF" [FileDependentDlgENG] DlgText = "Please select values for the follwing fields:" DlgType = "RadioCombination" DlgTemplate = "CW10" Caption = $(FunctionTitle) CBOptionsGreyed = {} NotifyFields = {NO, NO} HelpContext = $(!IDH_DB_OEMNADE2_INS) Combo1Label = "I/O Base:" Combo2Label = "IRQ Level:" Combo3Label = "Tx Rate:" Combo4Label = $(PHYParmLabel) Combo5Label = "Mode:" Combo6Label = "RTS Threshold:" Combo7Label = "Fragmentation Threshold" Combo8Label = "Power Saving:" Combo9Label = "Encryption:" Combo10Label = "Authentication:" Combo11Label = "Listen Interval:" Edit1Label = "SS ID:" CheckBox1 = "PCMCIA card" Combo1List = $(IOBaseAddrList) Combo1Out = $(IOBaseAddrUIVal) Combo2List = $(IRQList) Combo2Out = $(IRQValueUIVal) Combo3List = $(TxRateList) Combo3Out = $(TxRateUIVal) Combo4List = $(PHYParmList) Combo4Out = $(PHYParmUIVal) Combo5List = $(NetTypeList) Combo5Out = $(NetTypeUIVal) Combo6List = $(RTSThreshList) Combo6Out = $(RTSThreshUIVal) Combo7List = $(FragThreshList) Combo7Out = $(FragThreshUIVal) Combo8List = $(PSModeList) Combo8Out = $(PSModeUIVal) Combo9List = $(WepReqList) Combo9Out = $(WepReqUIVal) Combo10List = $(AuthenticationList) Combo10Out = $(AuthenticationUIVal) Combo11List = $(ListenIntervalList) Combo11Out = $(ListenIntervalUIVal) ComboListItemsIn = {Combo1List,Combo2List,Combo3List,+ Combo4List, Combo5List, Combo6List,+ Combo7List, Combo8List, Combo9List,+ Combo10List, Combo11List+ } ComboListItemsOut = {Combo1Out,Combo2Out,Combo3Out,+ Combo4Out, Combo5Out, Combo6Out,+ Combo7Out, Combo8Out, Combo9Out,+ Combo10Out, Combo11Out+ } EditTextIn = {$(SSIDValue)} EditTextLim = {"32"} CheckItemsIn = {$(Chk1)} [IOBaseAddrChoices] IOBase_1 = "4000",16384 IOBase_2 = "5000",20480 IOBase_3 = "6000",24576 IOBase_4 = "7000",28672 IOBase_5 = "8000",32768 IOBase_6 = "9000",36864 IOBase_7 = "A000",40960 IOBase_8 = "B000",45056 IOBase_9 = "C000",49152 IOBase_10 = "D000",53248 IOBase_19 = "180",384 IOBase_11 = "200",512 IOBase_12 = "240",576 IOBase_13 = "280",640 IOBase_14 = "2C0",714 IOBase_15 = "300",768 IOBase_16 = "340",832 IOBase_17 = "380",896 IOBase_18 = "3C0",960 [IRQChoices] IRQ_3 = "3",3 IRQ_4 = "4",4 IRQ_5 = "5",5 IRQ_7 = "7",7 IRQ_9 = "9",9 IRQ_10 = "10",10 IRQ_11 = "11",11 IRQ_12 = "12",12 IRQ_15 = "15",15 IRQ_na = "n/a",0 [IRQPciChoices] IRQ_pci = "n/a",0 [DSChanChoices] DSCHAN_1 = "1",1 DSCHAN_2 = "2",2 DSCHAN_3 = "3",3 DSCHAN_4 = "4",4 DSCHAN_5 = "5",5 DSCHAN_6 = "6",6 DSCHAN_7 = "7",7 DSCHAN_8 = "8",8 DSCHAN_9 = "9",9 DSCHAN_10 = "10",10 DSCHAN_11 = "11",11 [STA_NetTypeChoices] NETTYPE_ADHOC = "Ad Hoc",0 NETTYPE_INFRA = "Infrastructure",1 [STA_TxRateChoices] TXRATE_1 = "1 Mb/s", 1 TXRATE_2 = "2 Mb/s", 2 TXRATE_1_2 = "Auto 1 or 2 Mb/s", 3 TXRATE_55 = "5.5 Mb/s", 4 TXRATE_11 = "11 Mb/s", 8 TXRATE_ALL = "Fully Auto", 15 [STA_AuthenticationChoices] AUTHEN_OPEN = "Open System", 1 AUTHEN_SHARE = "Shared Key", 2 AUTHEN_AUTO = "Auto", 65535 [STA_ListenIntervalChoices] LISTENINT_1 = "1 Beacon Per", 1 LISTENINT_2 = "2 Beacon Per", 2 LISTENINT_3 = "3 Beacon Per", 3 LISTENINT_4 = "4 Beacon Per", 4 LISTENINT_5 = "5 Beacon Per", 5 LISTENINT_M = "Maximum", 1 [STA_PSModeChoices] PS_DIS = "Disabled", 1 PS_EN = "Enabled", 2 [RTSThreshChoices] RTSTHRESH_256 = "Always", 0 RTSTHRESH_256 = "256 Bytes", 256 RTSTHRESH_512 = "512 Bytes", 512 RTSTHRESH_768 = "768 Bytes", 768 RTSTHRESH_1024 = "1024 Bytes", 1024 RTSTHRESH_1280 = "1280 Bytes", 1280 RTSTHRESH_DIS = "Disabled", 2432 [FragThreshChoices] FRAGTHRESH_256 = "256 Bytes", 256 FRAGTHRESH_512 = "512 Bytes", 512 FRAGTHRESH_768 = "768 Bytes", 768 FRAGTHRESH_1024 = "1024 Bytes", 1024 FRAGTHRESH_1280 = "1280 Bytes", 1280 FRAGTHRESH_DIS = "Disabled", 2432 [WepReqChoices] WEP_DIS = "Disabled", 0 WEP_MAN = "64 bits", 2 WEP_EHN = "128 bits", 6 [STA_List] "PRISM2_5_PCMCIA" [DS_List] "PRISM2_5_PCMCIA" [ExCreateRegKey] Debug-Output "******************Entering [ExCreateRegKey]******************" set ECR_Result = NO_ERROR set ECR_BaseKeyHandle = $($0) set ECR_NewPath = $($1) set KeyNull = "" set MAXIMUM_ALLOWED = 33554432 Debug-Output "ExCreateRegKey - ECR_BaseKeyHandle = "$(ECR_BaseKeyHandle) Debug-Output " ECR_NewPath = "$(ECR_NewPath) Debug-Output " MAXIMUM_ALLOWED = "$(MAXIMUM_ALLOWED) Debug-Output " KeyNull = "$(KeyNull) OpenRegKey $(ECR_BaseKeyHandle) "" $(ECR_NewPath) $(MAXIMUM_ALLOWED) + ECR_BaseKey Debug-Output "ECR_BaseKey = "$(ECR_BaseKey) Debug-Output " OpenRegKey returned "$($R0) Ifstr $(ECR_BaseKey) == $(KeyNull) Debug-Output "ECR_BaseKey == KeyNull" Else Debug-Output "ECR_BaseKey != KeyNull" set ECR_KeyHandle = $(ECR_BaseKey) goto ECR_Return Endif set ECR_TmpPath = "" Split-String $(ECR_NewPath) "\" ECR_PList Debug-Output "ECR_PList = "$(ECR_PList) ForListDo $(ECR_PList) Ifstr(i) $($) != "\" Ifint $(#) == 1 set ECR_TmpPath = $($) Else set ECR_TmpPath = $(ECR_TmpPath)"\"$($) Endif Debug-Output "Determining if "$(ECR_TmpPath)" exists" OpenRegKey $(ECR_BaseKeyHandle) "" $(ECR_TmpPath) $(MAXIMUM_ALLOWED) ECR_BaseKey Ifstr $(ECR_BaseKey) == $(KeyNull) Debug-Output "Creating "$(ECR_TmpPath) CreateRegKey $(ECR_BaseKeyHandle) {$(ECR_TmpPath),0,GenericClass} "" $(MAXIMUM_ALLOWED) "" ECR_KeyHandle Ifstr(i) $(ECR_KeyHandle) == $(KeyNull) set ECR_Result = $($R0) goto ECR_Return Endif Endif Endif EndForListDo ECR_Return = + return $(ECR_Result) $(ECR_KeyHandle) ;*************************************************************** ; Default SECTIONS ;*************************************************************** [PCI-Defaults] set PollInDriverValue = 1 set IRQValueUIVal = "n/a" set IRQList = ^(IRQPciChoices, 1) set IRQValues = ^(IRQPciChoices, 2) exit [PCMCIA-Defaults] set PollInDriverValue = 0 set IRQValueUIVal = "7" set IRQList = ^(IRQChoices, 1) set IRQValues = ^(IRQChoices, 2) exit [Read-Defaults] ; set the default values ; I/O Base Address = 0x240 set IOBaseAddrUIVal = "240" ; IRQ Level = 9 ; set IRQValueUIVal = "7" ; PcmciaValue = 0/1 set PcmciaValue = 1 set Chk1 = "ON" ; Ethernet conversion mode = "Encapsulated"/"RFC1042"/"802.1h" ; set EthConvValue = "802.1h" set EthConvValue = 1 ; Station Mode related default values set PSLevelValue = 0; ; Power Save Mode = "Disabled"/"Basic"/"Enhanced" set PSModeList = $(STA_PSModeList) set PSModeValues = $(STA_PSModeValues) set PSModeUIVal = "Disabled" ; configure as infrastructure station set NetTypeList = $(STA_NetTypeList) set NetTypeValues = $(STA_NetTypeValues) set NetTypeUIVal = "Infrastructure" ; configure for 11 Mb/s default set TxRateList = $(STA_TxRateList) set TxRateValues = $(STA_TxRateValues) ; set TxRateUIVal = "2 Mb/s" set TxRateUIVal = "Fully Auto" ; configure for Authentication Open System set AuthenticationList = $(STA_AuthenticationList) set AuthenticationValues = $(STA_AuthenticationValues) set AuthenticationUIVal = "Auto" ; configure for Listen interval at MAX set ListenIntervalList = $(STA_ListenIntervalList) set ListenIntervalValues = $(STA_ListenIntervalValues) set ListenIntervalUIVal = "3 Beacon Per" ; configure for RTS/CTS disabled set RTSThreshList = $(RTSThreshList) set RTSThreshValues = $(RTSThreshValues) set RTSThreshUIVal = "Disabled" ; configure for Fragmentation disabled set FragThreshList = $(FragThreshList) set FragThreshValues = $(FragThreshValues) set FragThreshUIVal = "Disabled" ; configure for WEP Disabled set WepReqList = $(WepReqList) set WepReqValues = $(WepReqValues) set WepReqUIVal = "Disabled" ; PHY parameters DS set PHYParmName = "DSChannel"; set PHYParmList = $(DSChanList) set PHYParmValues = $(DSChanValues) set PHYParmUIVal = "6" set PHYParmLabel = "DS Channel:" ; Decryption to be done in Driver flag set DecryptInDriverValue = 1; ; Encryption to be done in Driver flag set EncryptInDriverValue = 1; ; WEP Factor value set WEPFactorValue = 3; ; IBSS to be managed by Driver flag set IBSSInDriverValue = 0; ; Set Preamble mode to Long=1 set PreambleModeValue = 1; ; default SSID - to be customized by OEM customer set SSIDValue = "any" exitDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.