1. e600.exe Driver
2. README.TXT File Contents

README.TXT Driver File Contents (e600.exe)

Release Notes

GCC Printing Software for Windows

December 1996

Congratulations on your purchase of a laser printer from GCC
Technologies. These release notes contain information that was not
included in the User's Manual, and applies to printers in the Elite
600 and SelectPress printer families. Additional release notes
specific to each printer may be found in the following files:

    Filename        Printer
    --------        -------
    ELITE600.TXT    Elite 600
    SPRESS.TXT      SelectPress

Please read the file corresponding to your printer model.

Complete Microsoft Windows Support
----------------------------------
The GCC Printing Software for Windows now includes support for the
following operating systems:  Windows 95; version 3.5 or later of
Windows NT; and version 3.1 or later of Windows or Windows for
Workgroups. For instructions on software installation procedures for
Windows 95 and Windows NT 3.5, please see the manual supplement which
accompanies this software release. However, please note the following
changes:  Windows NT 3.5 software has been placed in a subdirectory
named NT35; and Windows NT 4.0 software is in a subdirectory named
NT40, accompanied by a file named README.TXT which contains
installation instructions.

Windows 95 and parallel ports
-----------------------------
If you are using Windows 95 and have your GCC printer connected to your
computer's parallel port, please follow this procedure after using the
Add Printer Wizard to add the printer to your system:

  1. Click the printer's icon so it is highlighted.
  2. Click File in the menu bar and select Properties.
  3. Click the Details tab at the top of the dialog box.
  4. Click the Spool Settings... button near the bottom of the
     Details panel.
  5. Click the radio button labeled "Disable bi-directional support for
     this printer".
  6. Click OK to close the Spool Settings dialog box.
  7. Click OK to close the Properties dialog box.

Change to Windows PPD and PDX installation
------------------------------------------
Due to the addition of support for Microsoft Windows 95 and Windows NT,
the locations of the PPD and PDX files have changed. The PPD (format 4)
files are now in the root directory of the Printing Software disk, while
the PPD (format 3) and PDX files have been placed in a subdirectory
named PPD3. The Quark PDF files remain in the root directory.

To install the files on your hard disk, type a command similar to one of
the following.

For Adobe Illustrator 4.0 or 4.1:
    COPY A:\PPD3\*.PPD C:\AI4\PPD

For Adobe PageMaker 6.0:
    COPY A:\*.PPD C:\PM6\RSRC\USENGLSH\PPD4

For Aldus FreeHand 3.1 and earlier:
    COPY A:\PPD3\*.* C:\ALDUS\USENGLSH\PPDS

For Aldus FreeHand 4.0 and PageMaker 5.0:
    COPY A:\*.PPD C:\ALDUS\USENGLSH\PPD4

For Macromedia FreeHand 5.0:
    COPY A:\*.PPD C:\FH5\USENGLSH\PPD

For QuarkXPress:
    COPY A:\*.PDF C:\XPRESS

Depending on where you have installed any of these applications, the
path names may be different.

Windows 3.1 driver update for Elite 600 and SelectPress
-------------------------------------------------------
This software release contains an updated Windows 3.1 driver for the
Elite 600 and SelectPress printers. If you are using Windows 3.1, and
you previously had drivers installed for Elite 600 or SelectPress
printers, you should remove them before installing the updated driver.
Open the Printer control panel. You may wish to note the current
connection, settings, and options for each printer (see Chapter 4 of
the user's manual). Then, one at a time, select the Elite 600 and
SelectPress printers and click the Remove button. When you are done,
click the Close button. Then continue with the driver installation.

===================================================================

All trademarks and registered trademarks mentioned herein
are the property of their respective holders.