INSTALL.TXT Driver File Contents (AEF360TX-V144.exe)


           Driver Installation Guide for Packet Driver Requester
        ==========================================================

Introduction
============
    This document describes the procedure to setup the  Packet Driver for
    AEF-360TX Family PCI Fast Ethernet Adapter.

    Location of Driver: \PKTDRVR\RTSPKT.COM


Installation Procedure
======================
    1. Load the packet driver using the software interrupt and any
       optional switches if required.

       Usage: RTSPKT [options] <software_int_no> [media type]

       Example: RTSPKT -i 0x7e

       The only required  parameter is the software  interrupt.  A packet
       driver needs to have a software interrupt assigned to it for other
       programs to access it. The recommended interrupt 0x7e. If you need
       any of the  options  listed below,  place them before the software
       interrupt on the command line.

       -i - Force driver to report itself as 802.3 instead of Ethernet II
       -d - Delayed initialization.  Used for diskless booting
       -n - NetWare conversion.  Converts 802.3 packets into 8137 packets
       -w - Windows hack, obsoleted by winpkt
       -p - Promiscuous mode disable
       -h - Help
       -u - Uninstall

    2. Media type can be used to force the card to work on specific speed
       and duplex mode . If no media  type if specified, then driver will
       read hardware configuration from EEPROM on the card . The hardware
       configuration can be modified by running
       'rset8139' on driver disk.

    3. Type command ,  C:\RTSPKT  0x60 , the screen will appear following
       message:

       System: [345]86 processor, PCI bus, Two 8259s
       Packet driver software interrupt is 0x60
       Interrupt number is 0x9
       I/O port is 0x6100
       My Ethernet address is 52:54:4C:29:29:AD

    4. Installing Multiple LAN Adapters:

       If there are multiple network cards on the main board.the user run
       RTSPKT 0x60 directly, then the screen will display :

       There are 2 network cards on your main board :
       Card 1. IRQ= 0x9  I/O= 0x6100  NodeID= 52:54:4C:29:29:AD
       Card 2. IRQ= 0xA  I/O= 0x6000  NodeID= 52:54:4C:29:29:64
       Please select a Card No.(1-2): 1

       System: [345]86 processor, PCI bus, Two 8259s
       Packet driver software interrupt is 0x60
       Interrupt number is 0x9
       I/O port is 0x6100
       My Ethernet address is 52:54:4C:29:29:AD

    5. Installing multiple drivers:

       If you want to install multiple cards each connecting to different
       network, you have to install the driver multiple times, each  with
       different packet interrupt number. Then modify  'ioaddr'  variable
       in 'config.tel' to specify the packet inetrrupt you will use.


Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web3, load: 0.34