1. 201v320.zip Driver
2. NW312.TXT File Contents

NW312.TXT Driver File Contents (201v320.zip)

   Server Driver for Novell NetWare v3.12

   Introduction:
   -------------
   This document describes the procedure to install the NetWare v3.12
   server driver for AcerLAN ALN-201 PCI Ethernet adapter.

   Location of Driver:     \NWSERVER\ALN201.LAN
   Location of NLM:        \NWSERVER\312\ETHERTSM.NLM
                           \NWSERVER\312\MSM.NLM
                           \NWSERVER\312\NBI.NLM

   Installation Procedure:
   -----------------------
      Before you start with the installation process, make sure that
      the Novell NetWare 386 v3.12 server is properly installed.
      Similarly, your adapter should also be properly installed in your
      server.

      1. Insert the AcerLAN Driver Diskette into drive A and check the
         contents of subdirectory  \NWSERVER, It should contain the
         following files:

         ALN201.LAN---  Novell NetWare V3.12 Server Driver
         \312\ETHERTSM.NLM   (for Novell NetWare v3.12)
         \312\MSM.NLM        (for Novell NetWare v3.12)
         \312\NBI.NLM        (for Novell NetWare v3.12)

      2. If you can log into the server as a supervisor, copy the above
         files into the NetWare 386 subdirectory SYSTEM of your server.
         You can also copy the files to C:\nwserver subdirectory.

         Note: If ETHERTSM.NLM and MSM.NLM can't overwrite, you can
               use flag ETHERTSM.NLM (MSM.NLM) -Ro +Rw command
               to change the attribute of ETHERTSM.NLM (MSM.NLM).


      3. Run SERVER.EXE from your server. You will see a series of
         NetWare messages on screen.

      4. When the NetWare prompt appears (indicated by a colon),load
         your server driver. Simply type:

         : LOAD ALN201 <Enter>
         :
         or

         : LOAD C:\SERVER.312\NBI.NLM
         : LOAD C:\SERVER.312\MSM.NLM
         : LOAD C:\SERVER.312\ETHERTSM.NLM
         : LOAD C:\SERVER.312\ALN201

      5. Bind IPX to the adapter driver. At the NetWare server prompt,
         type:

         :BIND IPX TO ALN201 <Enter>

      6. After pressing <Enter> the computer prompts you for the Network
         Number. Give it a special number about its segment, or just
         a random number.

      7. Add the load and bind statements you require to the server's
         AUTOEXEC.NCF file so that the LAN driver will load automatically
         each time the server starts up.


   NOTES:
   ------
      1. Installing One LAN Adapter with Multiple Frame Types:

         When binding multiple frame types to one adapter, each LOAD
         statement will specify a different frame type.

           LOAD ALN201 SLOT=2 FRAME=ETHERNET_802.3 NAME=LAN8023
           BIND IPX TO LAN8023 NET=77777
           LOAD ALN201 SLOT=2 FRAME=ETHERNET_802.2 NAME=LAN8022
           BIND IPX TO LAN8022 NET=88888

      2. Installing Multiple LAN Adapters:

         When installing multiple LAN adapters, each LOAD statement
         must specify a correct SLOT number to avoid being prompted
         for which board to load the driver. For example:

           LOAD ALN201 SLOT=1 FRAME=ETHERNET_802.2 NAME=LAN_A
           BIND IPX TO LAN_A NET=222
           LOAD ALN201 SLOT=2 FRAME=EHTERNET_802.2 NAME=LAN_B
           BIND IPX TO LAN_B NET=333

      3. Installing Multiple LAN Adapters with Multiple Frame Types:
         In the situation, the SLOT and Frame types have to be specified.
         The following is an AUTOEXEC.NCF file example:

           FILE SERVER NAME NW312
           IPX INTERNAL NET 111
           LOAD ALN201 NAME=A SLOT=1 FRAME=ETHERNET_802.3
           BIND IPX A NET=11
           LOAD ALN201 NAME=B SLOT=1 FRAME=ETHERNET_802.2
           BIND IPX B NET=22
           LOAD ALN201 NAME=C SLOT=2 FRAME=ETHERNET_802.3
           BIND IPX C NET=33
           LOAD ALN201 NAME=D SLOT=2 FRAME=ETHERNET_802.2
           BIND IPX D NET=44

      4. How to edit the AUTOEXEC.NCF file
           a. At the NetWare prompt, run the INSTALL.NLM

              : LOAD INSTALL

           b. Select "System Options" and press <Enter>.

           c. Select "Edit AUTOEXEC.NCF File" and press <Enter>.
              Don't use "Create AUTOEXEC.NCF File", the option can't
              work ok.

           d. Exit the INSTALL module.


   If problems occur during the binding process, your screen will prompt
   you with error messages. Please refer to your NetWare 386 manual for
   details on these messages.