1. ob2000.zip Driver
2. README.TXT File Contents

README.TXT Driver File Contents (ob2000.zip)

                                                                      
HP OMNIBOOK 2000/5700 NOTEBOOK PC - WINDOWS 3.1 OR WINDOWS FOR WORKGROUPS
3.11, INSTALLING SCSI DRIVERS


INTRODUCTION
     
     The HP OmniBook 2000/5700 Notebook PC includes Microsoft (R) Windows
     for Workgroups 3.11 as one choice for the preloaded and preconfigured 
     operating system.  If you install retail Windows for Workgroups 3.11
     or Windows 3.1, follow these instructions to install the HP OmniBook
     Notebook PC SCSI drivers.
     
          
         NOTE:     The SCSI drivers are needed only if you are using
                   an HP OmniBook Notebook PC docking system.
     

REQUIREMENTS
     
     *    HP OmniBook 2000/5700 Notebook PC with Microsoft Windows 3.1 or
          Windows for Workgroups 3.11 installed.
     
     *    HP OmniBook 2000/5700 Notebook PC SCSI drivers. Use the drivers
          from the hard disk in the C:\OMNIBOOK\DRIVERS\WFW\SCSI directory
          or from the HP OmniBook 2000/5700 Notebook PC Recovery CD in the
          \OMNIBOOK\DRIVERS\WFW\SCSI directory. 
     

PROCEDURE
     
     1. In File Manager or at the MS-DOS (R) prompt, create a directory 
        named C:\PCSCSI.
     
     2. Copy the SCSI driver files from the drivers disk (or from
        C:\OMNIBOOK\DRIVERS\WFW\SCSI or from the Recovery CD) to the
        C:\PCSCSI directory.
     
     3. Open the C:\CONFIG.SYS file for editing.
     
     4. Add the following lines into CONFIG.SYS in the order shown.
        (You do not need the REM'ed lines. They are simply for
        explanation.)
          
	REM If SCSI BIOS is enabled (SCU setting), CB00-CFFF must be excluded.
        REM For example, if 8K is used for PCMCIA the EMM386 line would be
	REM device=c:\dos\emm386.exe noems x=c000-d1ff i=d200-e7ff x=e800-efff
	REM and if 32K is used for PCMCIA the EMM386 line would be
	REM device=c:\dos\emm386.exe noems x=c000-d7ff i=d800-e7ff x=e800-efff

	REM Environment variable to pass SCSI status to AUTOEXEC.BAT
	set aspi_scsi=1

	REM AMSIDA.SYS is SCSI ASPI layer.  It is required for SCSI devices 
	REM except if only a disk is being used and the SCSI BIOS is enabled 
        REM in the SCU.  Add "REM" not to load AMSIDA.SYS if no SCSI devices
        REM are used.  
	devicehigh=c:\pcscsi\amsida.sys /v

	REM AMSIRM.SYS supports SCSI hard disk drives.
	REM AMSIRM.SYS does not load if AMSIDA.SYS is not loaded or no SCSI
	REM hard disk drives are present.
	device=c:\pcscsi\amsirm.sys

	REM AMSICD.SYS supports SCSI CD-ROM drives.
	REM AMSICD.SYS does not load if AMSIDA.SYS is not loaded or no SCSI
	REM CD-ROM drives are present.
	devicehigh=c:\pcscsi\amsicd.sys /d:amdcd001

     5. Save the changes, then open the C:\AUTOEXEC.BAT file for
        editing.
     
     6. Add the following lines into AUTOEXEC.BAT in the order
        shown. (You do not need the REM'ed lines. They are simply
        for explanation.)
          
        REM For active SCSI status...
        if not %aspi_scsi%.==1. goto noscsi
        REM Add "REM" to beginning of next line if SCSI CD-ROM drive
        REM not installed
        c:\dos\mscdex /d:amdcd001 /d:mscd001 /m:12
     
     7. Save the changes, exit Windows, and press CTRL+ALT+DEL to
        reboot the HP OmniBook Notebook PC for the changes to take
        effect.

______________________________________________________________________
              Microsoft(R) is a U.S. registered trademark
                       of Microsoft Corporation
                                   
     Windows(R) or MS Windows(R) are U.S. registered trademarks of
                            Microsoft Corp.
                                   
             MS-DOS (R) is a U.S. registered trademark of
                        Microsoft Corporation.
                                   
                  Copyright  Hewlett-Packard Co. 1997
       This information is subject to change without notice and
                 is provided "as is" with no warranty.
          Hewlett-Packard shall not be liable for any direct,
        indirect, special, incidental or consequential damages
             in connection with the use of this material.

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

• Expand the archive file (if the download file is in zip or rar format).

• If the expanded file has an .exe extension, double click it and follow the installation instructions.

• Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

• Find the device and model you want to update in the device list.

• Double-click on it to open the Properties dialog box.

• From the Properties dialog box, select the Driver tab.

• Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.