SCOUNIX.TXT Driver File Contents (

<                          SMC Networks, Inc.                     >
<                    SMC EZ Card 10/100 (SMC1211TX)               >
<                        SCO UNIX STREAM DRIVER                   >
<                                                                 >
<                Copyright (C) 1998 SMC Networks, Inc.            >
<                       All Rights Reserved.                      >

The Unix driver contained in the directory \SCO is for the
following PCI Ethernet adapter:

        SMC EZ Card 10/100 (SMC1211TX)


        A. Installing MDI Unix Driver for SCO ODT 5.0
        B. Installing LLI Unix Driver for SCO 3.2.4 (ODT 3.0)

File Description

5.X\            SCO ODT 5.0 MDI Unix Driver

3.X\            SCO 3.2.4 (ODT 3.0) LLI Unix Driver

SCOUNIX.TXT     this file

A. Installing MDI Unix Driver for SCO ODT 5.0

 1. Log into the UNIX system as supervisor (root) and enter Maintenance mode.

    (Note: Make sure that the current directory is "/"
     using UNIX command - pwd.)

    Please follow the following steps to uncompress the package file:

    >  cd /tmp   (and insert the package floppy in the proper drive, i.e. a:)
    >  doscp a:/sco/5.x/vol.000 ./VOL.000.000

    Now the package installation directory is ready for installing.

3.  The following sections describe the configuration of the driver.
    We suggest that you perform these instructions in the
    single-user environment.

    Run the custom utility and select the "Install new package"

    Select Media Type "Media Image" and type Image Directory "/tmp "
    It will prompt with "SMC EZ Card 10/100 Adapter (ver 1.0.2)"

    After running the custom utility and the new package is installed,
    you should use the "netconfig" command to add the driver into your
    system as described in step 4 below.

 4. Run "netconfig". Add the desired chain.

 5. When the chain has been configured, select 'q' from the
    netconfig menu, and relink the kernel at the prompt.

 6. To activate the adapter, you must reboot. When the system
    boots, you should see the following message among the
    other configuration messages:

    %ethernet  0xD800-0xD81F   11   -   type=100 addr=00-00-e8-xx-xx-xx
     auto mode
     choice is auto negotiation mode
     Speed is 100 Mbps

    with the appropriate I/O addresses, IRQ, Adapter Type ,IEEE address and
    medium mode (auto,100full,100half,10full,10half).
    The display of the last three bytes of the IEEE address depends on the 
    adapter currently plugged onto your system.

 7. If you encounter any problems during installation,
    (i.e., an error message appears on screen) call your dealer for assistance.

B. Installing LLI Unix Driver for SCO 3.2.4 (ODT 3.0)

 1. Plug the SMC1211TX Fast Ethernet Adapter into a PCI slot
    in your PC machine.

 2. Turn ON the machine and login as "root" user. (In maintenance mode)

 3. Insert SMC SCO UNIX Driver diskette to floppy A: and
    enter the following command from Unix Shell to install the
    SCO Unix driver.

        # cd /tmp
        # doscp a:/sco/3.x/install .
        # chmod +x install
        # ./install

 4. The screen will prompt with the following message,

      Install SMC EZ Card 10/100 LLI Driver
      Please input source path ? (ex.: a:/sco/3.x)

 5. Enter the driver full path (a:/sco/3.x) and press the ENTER key
    to start copying the driver files to the Unix system.

 6. Run "netconfig" command from Unix shell.

        # netconfig

 7. Select "1. Add a chain" from the configuring chain options.

 8. Select "4. sco_tcp   SCO TCP/IP for UNIX" from the configuring
    protocol options.

 9. Select "18. r7e0   SMC EZ Card 10/100 Adapter LLI
    Driver, board 0" from the configuring driver options.

10. The system will prompt with the following message to complete
    configuration of the driver chain,
      Add chain sco_tcp->r7e0 (y/n): y
      Enter auto, force 100 or 10bps: (auto 10 100) [auto]
      or 'q' to quit: (press Enter key)
      Enter the internet address of this interface:
      Enter the netmask for this interface (default:
      (press Enter key)
      Does the interface use a broadcast address of all 1's? (y/n)
      (default: y): (press Enter key)
      Enter the broadcast address for this interface (default: (press Enter key)
      Are these values correct? (y/n): y
      Enter local host name or enter q to quit [sco324]: (press Enter key)
      32 Pseudo ttys ...
      Select an option or enter q to quit [q]: (press Enter key)
      256 TCP connections ...
      Select an option or enter q to quit [q]: (press Enter key)

11. Select "q. Quit" from the configuring chain options.
12. The system will prompt with the following message to relink
    the system kernel file,
      Do you want to relink the kernel now? y
      Do you want this kernel to boot by default? (y/n) y
      Do you want the kernel environment rebuilt? (y/n) y

13. Reboot the Unix system to initialize the driver function.

        # reboot


All Trademarks or Brand names mentioned are properties of
their respective companies.

== End of File ==
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web4, load: 0.45