SMC Networks Inc. SMC EZ Card 10 Ethernet PCI Network Cards Artisoft LANtastic v5.0 and v6.0 NDIS 2.01 Driver For Ethernet LAN Cards INSTALLATION GUIDE This software is licensed by SMC for use by its customers only. Copyright (c) 1997 SMC Networks Inc. All rights reserved. SUPPORTED NETWORK CARDS SMC's EZ Card 10 Ethernet PCI Network Cards: o SMC1208T o SMC1208BT o SMC1208BTA ============================== INSTALLATION FOR LANTASTIC 5.0 ============================== SMC's NDIS driver \NDIS\DOS\SMC1208.DOS may be used in place of AEXNDIS.DOS, the NDIS driver offered by ARTISOFT. Sample Configuration Files for 5.0 ---------------------------------- AUTOEXEC.BAT / STARTNET.BAT C:\LANTASTI\AI-NDIS BIND_TO=SMC1208_NIF C:\LANTASTI\AILANBIO C:\LANTASTI\REDIR MachineName CONFIG.SYS DEVICE=C:\LANTASTI\PROTMAN.DOS /I:C:\LANTASTI DEVICE=C:\LANTASTI\SMC1208.DOS ---> NDIS driver for SMC SMC1208 PROTOCOL.INI [PROTMAN] DRIVERNAME = PROTMAN$ DYNAMIC = YES [SMC1208_NIF] DRIVERNAME = SMC1208$ If you are using PROTMAN.DOS V1.x, the NO_BIND option must be used on the AI-NDIS command line in STARTNET.BAT, and NETBIND.EXE V1.x must be run before AILANBIO.EXE. ============================== INSTALLATION FOR LANTASTIC 6.0 ============================== Two alternative methods: A. Using the LANtastic 6.0 Install Program ------------------------------------------ NOTE: This method is required if LANtastic 6.0 has not yet been installed. 1. Start the LANtastic 6.0 Install program. 2. Select "NDIS support for network adapters." 3. Insert the SMC Driver Diskette for SMC's EZ Card 10 PCI cards and enter the path "A:\LANTASTI" (for floppy drive A). The Install program searches for SMC1208.DOS and PROTOCOL.INI (which are in \NDIS\DOS and \LANTASTI, respectively) and copies the files to the target directory. B. Using Manual Installation ---------------------------- NOTE: This method can be used if LANtastic 6.0 has been already installed. 1. Replace the old NDIS 2 driver (xxx.DOS) with the NDIS 2 driver for SMC's EZ Card 10 PCI cards -- \NDIS\DOS\SMC1208.DOS 2. Edit CONFIG.SYS, AUTOEXEC.BAT and PROTOCOL.INI as indicated below. AUTOEXEC.BAT / STARTNET.BAT @echo ===== Begin LANtastic configuration ===== SET LAN_CFG=C:\LANTASTI PATH C:\LANTASTI;%PATH% SET LAN_DIR=C:\LANTASTI.NET rem Please obtain the NETBEUI.EXE program from Microsoft NETBEUI AI-NDIS BIND_TO=SMC1208_NIF AILANBIO @STARTNET.CFG REDIR (login name) @STARTNET.CFG SERVER C:\LANTASTI.NET @STARTNET.CFG NET LOGIN \\(login name) @echo ===== End LANtastic configuration ===== CONFIG.SYS DEVICE=C:\LANTASTI\PROTMAN.DOS /I:C:\LANTASTI DEVICE=C:\LANTASTI\SMC1208.DOS ---> NDIS driver for SMC1208 models PROTOCOL.INI [PROTMAN] Priority=NETBEUI DriverName = PROTMAN$ Dynamic = Yes [NETBEUI_XIF] DriverName = netbeui$ Sessions = 6 NCBS = 12 Bindings = SMC1208_NIF LANABASE = 1 [SMC1208_NIF] DriverName = SMC1208$ This commercial computer software and documentation is provided with RESTRICTED RIGHTS. Use, duplication, or disclosure by the Government is subject to restrictions set forth in subparagraphs (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013, or subparagraphs (c) (1) and (2) of the Commercial Computer Software -- Restricted Rights clause at FAR 52.227-19, or Alternate III of the Rights in Data -- General clause at FAR 52.227-14, as applicable. The manufacturer / subcontractor is SMC Networks Inc., 6 Hughs, Irvine CA. SMC is a registered trademark, and EZ Card 10 is a trademark of SMC Networks Inc. Other product and company names are trademarks or registered trademarks of their respective holders. ====== The End ======Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.