1. ob800mmx.zip Driver
2. README.TXT File Contents

README.TXT Driver File Contents (ob800mmx.zip)

                Installing Microsoft Windows
                PCCard & Socket Services



System Installation Requirements

HP OmniBook 800 installed with Windows 3.1 or Windows for Workgroups

HP OmniBook 800 PCCARD Drivers.  These drivers are located on the OmniBook hard
   disk in C:\OMNIBOOK\DRIVERS\WFW\PCCARD.  These drivers are also located on
   the HP OmniBook Recovery CD in the \OmniBook\DRIVERS\WFW\PCCARD directory.

Note: If you are backing up these files to floppy disk, you will need two
      floppy disks.


Procedure

1.  From the DOS prompt or Windows File Manager create a directory called
    C:\CARDWIZ.

2.  Copy the PCCARD Drivers from C:\OMNIBOOK\DRIVERS\WFW\PCCARD\CARDWIZ or from
    your backup on floppy disk to C:\CARDWIZ.

3.  Enter the following lines into C:\CONFIG.SYS in the order shown.
    Note:  The REM lines need not be entered. They are simply for explanation
           of the driver.


REM -- OmniBook Socket Services driver required for card slot support
device=C:\CARDWIZ\SS365LP.EXE 

REM -- Card Services driver required for card slot support
devicehigh=C:\CARDWIZ\CS.EXE /POLL:1

REM -- Initial resource allocator required for card slot support
devicehigh=C:\CARDWIZ\CSALLOC.EXE

REM -- ATA card driver required for ATA cards
devicehigh=C:\CARDWIZ\ATADRV.EXE /S:2

REM -- Driver required for RAM cards
devicehigh=C:\CARDWIZ\MTSRAM.EXE

REM -- Memory card driver required for all memory cards
devicehigh=C:\CARDWIZ\MTDDRV.EXE

REM -- Card identification driver required for cards other than memory cards
devicehigh=C:\CARDWIZ\CARDID.EXE

REM -- Card Services APM support required for card slot support
install=C:\CARDWIZ\CS_APM.EXE



4.  Add the following lines to the [386Enh] section of C:\WINDOWS\SYSTEM.INI.
    (The simplest method of accomplishing this is to cut and paste from the
    README.TXT file located in the C:\OMNIBOOK\DRIVERS\WFW\PCCARD directory.)

COM2Base=2F8
COM2Irq=3
COM1Base=3F8
COM1Irq=4
device=C:\CARDWIZ\SSVRDD.386
device=C:\CARDWIZ\SSVCD311.386
device=C:\CARDWIZ\PCCARD.386
EmmExclude=D000-DFFF

... and after the "FileSysChange=off"

COM3Irq=5
COM3Base=3E8
COM4Irq=9
COM4Base=2E8

... and change "device=*vcd" to ";device=*vcd"


5.  Copy CTL3DV2.DLL from C:\OMNIBOOK\DRIVERS\WFW\PCCARD\WINDOWS\SYSTEM to
    C:\WINDOWS\SYSTEM.

6.  Reboot the OmniBook.



Maximizing memory for PC Cards

1.  In the default C:\CONFIG.SYS there are two emm386 lines.  The defaults are
    as follows:

device=c:\dos\emm386.exe noems x=d000-d1ff.  

(This allots 8K of memory for PC Card support. Add the REM statement to the
beginning of this line to allot 32K of memory for PC Card support.)

device=c:\dos\emm386.exe noems x=d000-d7ff.  

(This allots 32K of memory for PC Card support. Remove the REM to increase the
memory to 32K)