RELEASE.TXT Driver File Contents (Zoltrix_33_600_HSP_Modem.zip)

*************************************************************************
*                                                                       *
*                PC-TEl Inc.                                            *       
*       V34 Fax/Modem/Voice Release note                                *
*                                                                       *
*************************************************************************
02-05-96: Version 2.08B
Software:
	vmodem.386:
			improved V34 Connectivity
			improved V34 handshaking compatibility                  
	vpctcom.386:
			fixed some minor fax bugs
	ptserail.vxd:
			fixed compatibility problem with
			HyperTerminal in Windows 95



02-15-96: Version 2.09B
Software:
	vmodem.386:
			improved V34 S/N 
			improved V34 receive level
			fixed CD drop problem
			fixed V34 handshaking compatibility
			problem with Multi-Tech V34     

	PCTEL.INF:
			Chg SpeakerVolume_Low setting from "L0" to "L1".

	PTSERIAL.VXD:
			Fix PPP connect bug.
				 2.Fix PCTEL absent Bug

	setup.exe:
			Allow change path name.

02-22-96: Version 2.10
Software:
	vpctcom.386:
			support AT\N as AT\N0
			report RING BACK only when setting is ATX3 or ATX4
			exclude 0x0a from the aborting character list
	PTSERIAL.VXD
			fix receive delay dbug.

03-29-96: Version 2.11
Software:
	vmodem.386:     connectivity improvement
			retraining improvement
	vpctcom.386:    add commands for PTT test.
			report handset status in voice command mode.
	vvoice.386:     fix the initial noise during voice playback.
	
	pctel.inf:      HKR, Settings, ErrorControl_On,, "\N3"
			HKR, Settings, ErrorControl_Off,, "\N0"
			HKR, Settings, ErrorControl_Forced,, "\N4"
			HKR, Settings, Compression_On,, "%C3"
			HKR, Settings, Compression_Off,, "%C0"

			Removed those same lines from [NULL] section.

06-22-96: Version 2.12
Hardware:               
		1). Resistor R101 is changed to 2k(was 27.4k)Ohm, Capacitor C53 is changed
		    from 2200pf to 220pf on PCtel Revision D board
Software:
	General:
		1) Modem INF file modified, TAPI support added.
		2) Microsoft APM2.1 support added.
		3) Win95 installation sequence enhanced.  PCMCIA/PNP/Non PNP are combined
		in one diskette.
	vmodem.386:     
		1). Added CPU utilization feature(default 70 %)
		2). Improved v27 connectivity
		3). Improved V32 connectivity
		4). Improved V34 S/N
		5). Added V34 pre-emphasis filter
		6). Fixed V34 retrain problem with one
		    of AT&T DSP based V34 modem 
		7) Improved system hang problem due to connection drop initiated 
		from remote modem.
		8) Retrain handling improvement.
		9) Japan Link connection improvement.
		10) Transmit level in all modes.
	      
	vpctcom.386:
		1) Auto mode connection to some low speed modem.
		2) CNG detection in voice command mode.
		3) S6,S8 timer modified.
		4) ATD@ command.
		5) Bug fixed for Q1 setting
		6) &K5 (transparent XON/XOFF flow control) enables both local 
		and remote XON/XOFF flow control, same as what Rockwell-based 
		modems do. This "transparent" flow control is totally different 
		from the original definition of transparent XON/XOFF flow control by Hayes.
		7) For &S1 setting, DSP CD off caused by re-train won't lower 
		UART DSR now. Data-DSP still has problems to keep its DSR_BIT 
		consistent for both auto and fixed modes during the handshaking 
		so you can see blinks on DSR light.
		8) "TIES" escape sequence is corrected. *Qn command are added.
		9) Transmit data stream in Direct Data Mode is regulated.
		10). Default Transmit level is -11 dBm  
		11). 50ms fax Tx termination delay added to improve fax compatibility
		12) Fix bug which causes sound level to change when pause function is 
		selected in voice playback.
		13) Enable class 1 mode switch in class 8 mode.
			
	vvoice.386:
		1).Fixed busy tone detection

07-26-96: Version 2.15
New features:
	1) V.34bis/33.6kbps is added.
	2) HSP speakerphone feature is enabled.  This feature requires the full
	duplex audio driver support, such as: Crystal 4236/4232, ESS 1868/1888, 
	Opti 931 and Creative Vibra 16.
	3) International call progress tone handling (via %I command) are 
	added.
	4) Microsoft Visual C++4.2 are used for file generation.
	5) V.34 rate renegotiation is added.
Bug fixed:
	1) Power management mode handling is modified.
	2) Microsoft Phone voice playback volume issue fixed.
Known problem:
	1) ATD^ command does not generate calling tone in data mode.
	2) Quicklink and SuperVoice DTE speed should be set at 57600 or below.         
	



Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web5, load: 1.15