;***********************************************************************
;
; OEMSETUP.INF
;
; Version 4.16
;
; Olicom network card and driver SETUP INF file.
;
;***********************************************************************
;-----------------------------------------------------------------------
; OPTION TYPE
; -----------
; This identifies the Option type we are dealing with. The different
; possible types are:
;
; COMPUTER, DISPLAY, MOUSE, KEYBOARD, LAYOUT, SCSI, PRINTER, ...
;
; Types specific to networking:
;
; NetAdapter, a netcard / adapter combination or just a netcard
; NetDriver, just a netcard driver
; NetTransport, a complete NDIS-compliant TDI transport stack
; NetService, an NT networking service
; NetWork, a complete network ensemble.
; NetProvider a complete network which supports NT MPR protocol
;-----------------------------------------------------------------------
[Identification]
OptionType = NetAdapter
;-----------------------------------------------------------------------
; PlatformsSupported
; ------------------
; This identifies the platforms supported by the adapter card.
; Possible types are:
;
; ISA, EISA, MCA, "Jazz-Internal Bus", PC Card and PCI
;-----------------------------------------------------------------------
[PlatformsSupported]
ISA
EISA
MCA
"Jazz-Internal Bus"
PCMCIA
PCI
[LanguagesSupported]
ENG
;-----------------------------------------------------------------------
; OPTION LIST
; -----------
; This section lists the OEM Option key names. These keys are locale
; independent and used to represent the option in a locale independent
; manner.
;
;-----------------------------------------------------------------------
[Options]
; OCTK3117
; OCTK3118
; OCTK3133
; OCTK3136
OCTK3137
; OCTK3129
; OCTK3220
; OCTK3221
; OCTK3230
; OCTK3232
OCTK16
PCMCIA
COMBO
[OptionsTextENG]
; OCTK3117 = "Olicom Token-Ring ISA 16/4 (OC-3117)"
; OCTK3118 = "Olicom Token-Ring ISA 16/4 (OC-3118)"
; OCTK3133 = "Olicom Token-Ring EISA 16/4 (OC-3133)"
; OCTK3136 = "Olicom Token-Ring PCI 16/4 Adapter (OC-3136)"
OCTK3137 = "Olicom Token-Ring PCI/II 16/4 Adapter (OC-3137)"
; OCTK3129 = "Olicom Token-Ring MCA 16/4 (OC-3129)"
; OCTK3220 = "Olicom GoCard Token-Ring PC Card (OC-3220)"
; OCTK3221 = "Olicom GoCard Token-Ring PC Card (OC-3221)"
; OCTK3230 = "Olicom GoCard TR/Modem 144 PC Card (OC-3230)"
; OCTK3232 = "Olicom GoCard TRN/Modem 336 PC Card (OC-3232)"
[IOBaseAddrChoices]
IOBase_0 = "Auto detect", 0
IOBase_1 = "0A00-0A1F", 2560
IOBase_2 = "0A20-0A3F", 2592
IOBase_3 = "0A40-0A5F", 2624
IOBase_4 = "0A60-0A7F", 2656
IOBase_5 = "0A80-0A9F", 2688
IOBase_6 = "0AA0-0ABF", 2720
IOBase_7 = "0AC0-0ADF", 2752
IOBase_8 = "0AE0-0AFF", 2874
IOBase_9 = "0B00-0B1F", 2816
IOBase_10 = "0B20-0B3F", 2848
IOBase_11 = "0B40-0B5F", 2880
IOBase_12 = "0B60-0B7F", 2912
IOBase_13 = "0B80-0B9F", 2944
IOBase_14 = "0BA0-0BBF", 2976
IOBase_15 = "0BC0-0BDF", 3008
IOBase_16 = "0BE0-0BFF", 3040
IOBase_20 = "0A20-0A23,0A30-0A3F", 2592
IOBase_21 = "0A24-0A27,0A40-0A4F", 2596
IOBase_22 = "0A50-0A53,0A60-0A6F", 2640
IOBase_23 = "0A54-0A57,0A70-0A7F", 2644
[ReceiveBufferCountChoices]
RBC_1 = "32",32
RBC_2 = "31",31
RBC_3 = "30",30
RBC_4 = "29",29
RBC_5 = "28",28
RBC_6 = "27",27
RBC_7 = "26",26
RBC_8 = "25",25
RBC_9 = "24",24
RBC_10 = "23",23
RBC_11 = "22",22
RBC_12 = "21",21
RBC_13 = "20",20
RBC_14 = "19",19
RBC_15 = "18",18
RBC_16 = "17",17
RBC_17 = "16",16
RBC_18 = "15",15
RBC_19 = "14",14
RBC_20 = "13",13
RBC_21 = "12",12
RBC_22 = "11",11
RBC_23 = "10",10
RBC_24 = "9",9
RBC_25 = "8",8
RBC_26 = "7",7
RBC_27 = "6",6
RBC_28 = "5",5
[TransmitBufferCountChoices]
XBC_1 = "32",32
XBC_2 = "31",31
XBC_3 = "30",30
XBC_4 = "29",29
XBC_5 = "28",28
XBC_6 = "27",27
XBC_7 = "26",26
XBC_8 = "25",25
XBC_9 = "24",24
XBC_10 = "23",23
XBC_11 = "22",22
XBC_12 = "21",21
XBC_13 = "20",20
XBC_14 = "19",19
XBC_15 = "18",18
XBC_16 = "17",17
XBC_17 = "16",16
XBC_18 = "15",15
XBC_19 = "14",14
XBC_20 = "13",13
XBC_21 = "12",12
XBC_22 = "11",11
XBC_23 = "10",10
XBC_24 = "9",9
XBC_25 = "8",8
XBC_26 = "7",7
XBC_27 = "6",6
XBC_28 = "5",5
XBC_29 = "4",4
XBC_30 = "3",3
XBC_31 = "2",2
[MaxFrameSizeChoices]
MFS_1 = "18000 Bytes",18000
MFS_2 = "16384 Bytes",16384
MFS_3 = "14336 Bytes",14336
MFS_4 = "12288 Bytes",12288
MFS_5 = "10240 Bytes",10240
MFS_6 = "8192 Bytes",8192
MFS_7 = "7168 Bytes",7168
MFS_8 = "6144 Bytes",6144
MFS_9 = "5120 Bytes",5120
MFS_10 = "4540 Bytes",4540
MFS_11 = "4472 Bytes",4472
MFS_12 = "4096 Bytes",4096
MFS_13 = "3584 Bytes",3584
MFS_14 = "3072 Bytes",3072
MFS_15 = "2560 Bytes",2560
MFS_16 = "2048 Bytes",2048
MFS_17 = "1792 Bytes",1792
MFS_18 = "1536 Bytes",1536
MFS_19 = "1280 Bytes",1280
MFS_20 = "1024 Bytes",1024
MFS_21 = "512 Bytes",512
[IOBasePCMCIAChoices]
; 3E0h is where PCIC is (normally) located
; 240h is where TCIC is (normally) located
; therefore user cannot select these for locating the adapter
IOBase_1 = "200h",512
IOBase_2 = "220h",544
IOBase_3 = "260h",608
IOBase_4 = "280h",640
IOBase_5 = "2A0h",672
IOBase_6 = "2C0h",714
IOBase_7 = "2E0h",746
IOBase_8 = "300h",768
IOBase_9 = "320h",800
IOBase_10 = "340h",832
IOBase_11 = "360h",864
IOBase_12 = "380h",896
IOBase_13 = "3A0h",928
IOBase_14 = "3C0h",960
IOBase_15 = "A00h",2560
IOBase_16 = "A20h",2592
IOBase_17 = "A40h",2624
IOBase_18 = "A60h",2656
IOBase_19 = "A80h",2688
IOBase_20 = "AA0h",2720
IOBase_21 = "AC0h",2752
IOBase_22 = "AE0h",2784
IOBase_23 = "B00h",2816
IOBase_24 = "B20h",2848
IOBase_25 = "B40h",2880
IOBase_26 = "B60h",2912
IOBase_27 = "B80h",2944
IOBase_28 = "BA0h",2976
IOBase_29 = "BC0h",3008
IOBase_30 = "BE0h",3040
[MemWinChoices]
MemWin_1 = "A0000h", 655360
MemWin_2 = "A1000h", 659456
MemWin_3 = "A2000h", 663552
MemWin_4 = "A3000h", 667648
MemWin_5 = "A4000h", 671744
MemWin_6 = "A5000h", 675840
MemWin_7 = "A6000h", 679936
MemWin_8 = "A7000h", 684032
MemWin_9 = "A8000h", 688128
MemWin_10 = "A9000h", 692224
MemWin_11 = "AA000h", 696320
MemWin_12 = "AB000h", 700416
MemWin_13 = "AC000h", 704512
MemWin_14 = "AD000h", 708608
MemWin_15 = "AE000h", 712704
MemWin_16 = "AF000h", 716800
MemWin_17 = "B0000h", 720896
MemWin_18 = "B1000h", 724992
MemWin_19 = "B2000h", 729088
MemWin_20 = "B3000h", 733184
MemWin_21 = "B4000h", 737280
MemWin_22 = "B5000h", 741376
MemWin_23 = "B6000h", 745472
MemWin_24 = "B7000h", 749568
MemWin_25 = "B8000h", 753664
MemWin_26 = "B9000h", 757760
MemWin_27 = "BA000h", 761856
MemWin_28 = "BB000h", 765952
MemWin_29 = "BC000h", 770048
MemWin_30 = "BD000h", 774144
MemWin_31 = "BE000h", 778240
MemWin_32 = "BF000h", 782336
MemWin_33 = "C0000h", 786432
MemWin_34 = "C1000h", 790528
MemWin_35 = "C2000h", 794624
MemWin_36 = "C3000h", 798720
MemWin_37 = "C4000h", 802816
MemWin_38 = "C5000h", 806912
MemWin_39 = "C6000h", 811008
MemWin_40 = "C7000h", 815104
MemWin_41 = "C8000h", 819200
MemWin_42 = "C9000h", 823296
MemWin_43 = "CA000h", 827392
MemWin_44 = "CB000h", 831488
MemWin_45 = "CC000h", 835584
MemWin_46 = "CD000h", 839680
MemWin_47 = "CE000h", 843776
MemWin_48 = "CF000h", 847872
MemWin_49 = "D0000h", 851968
MemWin_50 = "D1000h", 856064
MemWin_51 = "D2000h", 860160
MemWin_52 = "D3000h", 864256
MemWin_53 = "D4000h", 868352
MemWin_54 = "D5000h", 872448
MemWin_55 = "D6000h", 876544
MemWin_56 = "D7000h", 880640
MemWin_57 = "D8000h", 884736
MemWin_58 = "D9000h", 888832
MemWin_59 = "DA000h", 892928
MemWin_60 = "DB000h", 897024
MemWin_61 = "DC000h", 901120
MemWin_62 = "DD000h", 905216
MemWin_63 = "DE000h", 909312
MemWin_64 = "DF000h", 913408
MemWin_65 = "E0000h", 917504
MemWin_66 = "E1000h", 921600
MemWin_67 = "E2000h", 925696
MemWin_68 = "E3000h", 929792
MemWin_69 = "E4000h", 933888
MemWin_70 = "E5000h", 937984
MemWin_71 = "E6000h", 942080
MemWin_72 = "E7000h", 946176
MemWin_73 = "E8000h", 950272
MemWin_74 = "E9000h", 954368
MemWin_75 = "EA000h", 958464
MemWin_76 = "EB000h", 962560
MemWin_77 = "EC000h", 966656
MemWin_78 = "ED000h", 970752
MemWin_79 = "EE000h", 974848
MemWin_80 = "EF000h", 978944
MemWin_81 = "F0000h", 983040
MemWin_82 = "F1000h", 987136
MemWin_83 = "F2000h", 991232
MemWin_84 = "F3000h", 995328
MemWin_85 = "F4000h", 999424
MemWin_86 = "F5000h", 1003520
MemWin_87 = "F6000h", 1007616
MemWin_88 = "F7000h", 1011712
MemWin_89 = "F8000h", 1015808
MemWin_90 = "F9000h", 1019904
MemWin_91 = "FA000h", 1024000
MemWin_92 = "FB000h", 1028096
MemWin_93 = "FC000h", 1032192
MemWin_94 = "FD000h", 1036288
MemWin_95 = "FE000h", 1040384
MemWin_96 = "FF000h", 1044480
[InterruptChoices]
Interrupt_1 = "3", 3
Interrupt_2 = "4", 4
Interrupt_3 = "5", 5
Interrupt_4 = "7", 7
Interrupt_5 = "9", 9
Interrupt_6 = "10",10
Interrupt_7 = "11",11
Interrupt_8 = "12",12
Interrupt_9 = "14",14
Interrupt_10 = "15",15
[ComPortChoices]
Com_1 = "COM1", 1016
Com_2 = "COM2", 760
Com_3 = "COM3", 1000
Com_4 = "COM4", 744
Com_5 = "COM5", 24
Com_6 = "Disabled", 0
[IOBasePCMCIAControllerChoices]
IOBase_1 = "Olicom Enabler",992
IOBase_2 = "Olicom Enabler (3E2h)",994
;;;IOBase_3 = "Windows NT Enabler",0
[WaitstateChoices]
Waitstate_1 = "0", 0
Waitstate_2 = "1", 1
Waitstate_3 = "2", 2
Waitstate_4 = "3", 3
Waitstate_5 = "4", 4
Waitstate_6 = "5", 5
Waitstate_7 = "6", 6
Waitstate_8 = "7", 7
Waitstate_9 = "8", 8
Waitstate_10 = "9", 9
Waitstate_11 = "10",10
Waitstate_12 = "11",11
Waitstate_13 = "12",12
Waitstate_14 = "13",13
Waitstate_15 = "14",14
Waitstate_16 = "15",15
[DatasizeChoices]
Datasize_1 = 1, 1,"&16 Bit"
Datasize_2 = 2, 0,"&8 Bit"
[RingSpeedChoices]
RS_1 = "16 Mbps", 16
RS_2 = "4 Mbps", 4
[RSChoices]
RS_1 = "Adapter setting", 255
RS_2 = "Force 16 Mbps", 16
RS_3 = "Force 4 Mbps", 4
;-----------------------------------------------------------------------
; Constants for use with dialogs
;-----------------------------------------------------------------------
[FileConstants]
UtilityInf = "UTILITY.INF"
subroutineinf = "SUBROUTN.INF"
SoftwareType = "driver"
Exit_Code = 0
DialogDllName = "octk16.dll"
HelpfileName = "octk16.hlp"
NetEventDLL = "%SystemRoot%\System32\netevent.dll;%SystemRoot%\System32\Drivers\Octk16.sys"
IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll"
Manufacturer = "Olicom"
ProductMajorVersion = "1"
ProductMinorVersion = "00"
ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion)
ProductSoftwareName = "OcTk16"
ProductSoftwareTitle = "Olicom Token-Ring 16/4 Adapter Driver"
ProductSoftwareImagePath = "\SystemRoot\System32\drivers\octk16.sys"
NetRuleSoftwareType = "octk16Sys ndisDriver octk16Driver"
NetRuleSoftwareUse = $(SoftwareType)
NetRuleSoftwareBindForm = """Octk16Sys"" yes no container"
NetRuleSoftwareClass = {"octk16Driver basic"}
NetRuleSoftwareBindable = {"octk16Driver octk16Adapter non exclusive 100"}
ProductHardwareName = "OcTk16"
ProductHardwareOCTK3117Title = "Olicom Token-Ring ISA 16/4 (OC-3117)"
ProductHardwareOCTK3118Title = "Olicom Token-Ring ISA 16/4 (OC-3118)"
ProductHardwareOCTK3133Title = "Olicom Token-Ring EISA 16/4 (OC-3133)"
ProductHardwareOCTK3136Title = "Olicom Token-Ring PCI 16/4 Adapter (OC-3136)"
ProductHardwareOCTK3137Title = "Olicom Token-Ring PCI/II 16/4 Adapter (OC-3137)"
ProductHardwareOCTK3129Title = "Olicom Token-Ring MCA 16/4 (OC-3129)"
ProductHardwareOCTK3220Title = "Olicom GoCard Token-Ring PC Card (OC-3220)"
ProductHardwareOCTK3221Title = "Olicom GoCard Token-Ring PC Card (OC-3221)"
ProductHardwareOCTK3230Title = "Olicom GoCard TR/Modem 144 PC Card (OC-3230)"
ProductHardwareOCTK3232Title = "Olicom GoCard TRN/Modem 336 PC Card (OC-3232)"
NetRuleHardwareType = "octk16 octk16Adapter"
NetRuleHardwareBindForm = " yes yes container"
NetRuleHardwareClass = {"octk16Adapter basic"}
ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion"
ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters"
[GeneralConstants]
from = ""
to = ""
ExitCodeOk = 0
ExitCodeCancel = 1
ExitCodeFatal = 2
KeyNull = ""
MAXIMUM_ALLOWED = 33554432
RegistryErrorIndex = NO_ERROR
KeyProduct = ""
KeyParameters = ""
TRUE = 1
FALSE = 0
NoTitle = 0
ExitState = "Active"
OldVersionExisted = $(FALSE)
DriverPath = $(!STF_NTPATH)\drivers
PCIDetectSupported = $(TRUE)
NT40VersionConstant = "4.0"
NT351VersionConstant = "3.51"
NT350VersionConstant = "3.50"
NT310VersionConstant = "3.10"
[FileConstantsENG]
ProCaption = "Windows NT Setup"
ProCancel = "Cancel"
ProCancelMsg = "Windows NT Networking is not correctly installed. "+
"Are you sure you want to cancel copying files?"
ProCancelCap = "Network Setup Message"
ProText1 = "Copying:"
ProText2 = "To:"
ProductHardwareOCTK3117Description = "Olicom Token-Ring ISA 16/4 (OC-3117)"
ProductHardwareOCTK3118Description = "Olicom Token-Ring ISA 16/4 (OC-3118)"
ProductHardwareOCTK3133Description = "Olicom Token-Ring EISA 16/4 (OC-3133)"
ProductHardwareOCTK3136Description = "Olicom Token-Ring PCI 16/4 Adapter (OC-3136)"
ProductHardwareOCTK3137Description = "Olicom Token-Ring PCI/II 16/4 Adapter (OC-3137)"
ProductHardwareOCTK3129Description = "Olicom Token-Ring MCA 16/4 (OC-3129)"
ProductHardwareOCTK3220Description = "Olicom GoCard Token-Ring PC Card (OC-3220)"
ProductHardwareOCTK3221Description = "Olicom GoCard Token-Ring PC Card (OC-3221)"
ProductHardwareOCTK3230Description = "Olicom GoCard TR/Modem 144 PC Card (OC-3230)"
ProductHardwareOCTK3232Description = "Olicom GoCard TRN/Modem 336 PC Card (OC-3232)"
ProductSoftwareDescription = "Olicom Token-Ring Adapter Driver"
ProductHardwareDescription = "Olicom Token-Ring Adapter"
FunctionTitle = "Olicom Token-Ring Setup"
IOBaseAddrList = ^(IOBaseAddrChoices, 1)
IOBaseAddrValues = ^(IOBaseAddrChoices, 2)
RcvBufCountList = ^(ReceiveBufferCountChoices, 1)
RcvBufCountValues = ^(ReceiveBufferCountChoices, 2)
XmitBufCountList = ^(TransmitBufferCountChoices, 1)
XmitBufCountValues = ^(TransmitBufferCountChoices, 2)
FrameSizeList = ^(MaxFrameSizeChoices, 1)
FrameSizeValues = ^(MaxFrameSizeChoices, 2)
IOBasePCMCIAList = ^(IOBasePCMCIAChoices, 1)
IOBasePCMCIAValues = ^(IOBasePCMCIAChoices, 2)
MemWinList = ^(MemWinChoices, 1)
MemWinValues = ^(MemWinChoices, 2)
InterruptList = ^(InterruptChoices, 1)
InterruptValues = ^(InterruptChoices, 2)
RingSpeedList = ^(RingSpeedChoices, 1)
RingSpeedValues = ^(RingSpeedChoices, 2)
RSList = ^(RSChoices, 1)
RSValues = ^(RSChoices, 2)
ComPortList = ^(ComPortChoices, 1)
ComPortValues = ^(ComPortChoices, 2)
IOBasePCMCIAControllerList = ^(IOBasePCMCIAControllerChoices, 1)
IOBasePCMCIAControllerValues = ^(IOBasePCMCIAControllerChoices, 2)
WaitstateList = ^(WaitstateChoices, 1)
WaitstateValues = ^(WaitstateChoices, 2)
DatasizeList = ^(DatasizeChoices, 1)
DatasizeValues = ^(DatasizeChoices, 2)
DatasizeLabels = ^(DatasizeChoices, 3)
; Parameter defaults
IOBasePCMCIADefault = 15
MemWinDefault = 49
ComPortDefault = 3
InterruptDefault = 3
; Bus/slot defaults for PCI auto-detect
BusNoDefault = 0
SlotNoDefault = 0
SlotNoUnknown = 1024
[DialogConstantsENG]
Help = "&Help"
Exit = "Cancel"
OK = "OK"
HelpContext = ""
Continue = "Continue"
Cancel = "Cancel"
ContextMinimumID = 6000
ContextContentsID = 6000
ContextPCMCIASetupID = 6001
ContextPCMCIAAdvancedID = 6002
ContextMaximumID = 6020
[date]
Now = {} ? $(!LIBHANDLE) GetSystemDate
[AskSourceDlgText]
DlgText = "Please enter the full path of the Olicom 16/4 driver "+
"setup files. Then choose Continue."
;-----------------------------------------------------------------------
; ADAPTER PARAMETER DIALOG
; ------------------------
; This section sets up the adapter parameter dialog. All textstrings
; presented in this dialog are defined here.
;
;-----------------------------------------------------------------------
[OCTK16ParameterDlgENG]
DlgType = "RadioCombination"
DlgTemplate = "OCTK16"
Caption = $(FunctionTitle)
DlgText = "Please select values for the following fields:"
Free = "&Bus..."
Combo1Label = "&I/O Base Address:"
Combo2Label = "&Receive Buffers:"
Combo3Label = "&Transmit Buffers:"
Combo4Label = "&Max Frame Size:"
Combo5Label = "Ring &Speed:"
Label1 = "&Early Token Release:"
Radio1 = "Yes"
Radio2 = "No"
Label2 = "&Full Transmit Status:"
Radio3 = "Yes"
Radio4 = "No"
Edit1Label = "&Network Address:"
Combo1List = $(IOBaseAddrList)
Combo1Out = $(IOBaseAddrIndex)
Combo2List = $(RcvBufCountList)
Combo2Out = $(RcvBufCountIndex)
Combo3List = $(XmitBufCountList)
Combo3Out = $(XmitBufCountIndex)
Combo4List = $(FrameSizeList)
Combo4Out = $(FrameSizeIndex)
Combo5List = $(RSList)
Combo5Out = $(RSIndex)
ComboListItemsIn = {Combo1List, Combo2List, Combo3List, Combo4List, Combo5List}
ComboListItemsOut = {Combo1Out, Combo2Out, Combo3Out, Combo4Out, Combo5Out}
EditTextLim = 17
EditTextIn = $(NetworkAddress)
RadioOptionGreyed = {}
CBOptionsGreyed = {}
NotifyFields = {NO, NO, NO, NO, NO, NO}
HelpContext = $(ContextContentsID)
;-----------------------------------------------------------------------
; PCMCIA PARAMETER MAIN DIALOG
; ----------------------------
; This section sets up the adapter parameter dialog. All textstrings
; presented in this dialog are defined here.
;
;-----------------------------------------------------------------------
[PCMCIAParameterDlgENG]
DlgType = "RadioCombination"
DlgTemplate = "PCMCIA"
Caption = $(FunctionTitle)
DlgText = "Please select values for the following fields:"
Free = "&Pc Card..."
Combo1Label = "&Receive Buffers:"
Combo2Label = "&Transmit Buffers:"
Combo3Label = "&Max Frame Size:"
Label1 = "&Early Token Release:"
Radio1 = "Yes"
Radio2 = "No"
Label2 = "&Full Transmit Status:"
Radio3 = "Yes"
Radio4 = "No"
Edit1Label = "&Network Address:"
Combo1List = $(RcvBufCountList)
Combo1Out = $(RcvBufCountIndex)
Combo2List = $(XmitBufCountList)
Combo2Out = $(XmitBufCountIndex)
Combo3List = $(FrameSizeList)
Combo3Out = $(FrameSizeIndex)
ComboListItemsIn = {Combo1List, Combo2List, Combo3List}
ComboListItemsOut = {Combo1Out, Combo2Out, Combo3Out}
EditTextLim = 17
EditTextIn = $(NetworkAddress)
RadioOptionGreyed = {}
CBOptionsGreyed = {}
NotifyFields = {NO, NO, NO, NO}
HelpContext = $(ContextContentsID)
;-----------------------------------------------------------------------
; PCMCIA COMBO Cards PARAMETER MAIN DIALOG
; ----------------------------------------
; This section sets up the adapter parameter dialog. All textstrings
; presented in this dialog are defined here.
;
;-----------------------------------------------------------------------
[COMBOParameterDlgENG]
DlgType = "RadioCombination"
DlgTemplate = "PCMCIA"
Caption = $(FunctionTitle)
DlgText = "Please select values for the following fields:"
Free = "&Pc Card..."
Combo1Label = "&Receive Buffers:"
Combo2Label = "&Transmit Buffers:"
Combo3Label = "&Max Frame Size:"
Label1 = "&Early Token Release:"
Radio1 = "Yes"
Radio2 = "No"
Label2 = "&Full Transmit Status:"
Radio3 = "Yes"
Radio4 = "No"
Edit1Label = "&Network Address:"
Combo1List = $(RcvBufCountList)
Combo1Out = $(RcvBufCountIndex)
Combo2List = $(XmitBufCountList)
Combo2Out = $(XmitBufCountIndex)
Combo3List = $(FrameSizeList)
Combo3Out = $(FrameSizeIndex)
ComboListItemsIn = {Combo1List, Combo2List, Combo3List}
ComboListItemsOut = {Combo1Out, Combo2Out, Combo3Out}
EditTextLim = 17
EditTextIn = $(NetworkAddress)
RadioOptionGreyed = {}
CBOptionsGreyed = {}
NotifyFields = {NO, NO, NO, NO}
HelpContext = $(ContextContentsID)
;-----------------------------------------------------------------------
; MORE PCMCIA PARAMETER DIALOG
; ----------------------------
; This section sets up the PCMCIA parameter dialog. All textstrings
; presented in this dialog are defined here.
;
;-----------------------------------------------------------------------
[PCMCIAMoreDlgENG]
DlgType = "RadioCombination"
DlgTemplate = "PCMCIAM"
Caption = "Pc Card Setup"
DlgText = "Please select values for the following fields:"
Free = "&Advanced..."
Combo1Label = "I/O &Base Address:"
Combo2Label = "&Memory Window:"
Combo3Label = "&Interrupt:"
Combo4Label = "&Ring Speed:"
Combo1List = $(IOBasePCMCIAList)
Combo1Out = $(IOBasePCMCIAIndex)
Combo2List = $(MemWinList)
Combo2Out = $(MemWinIndex)
Combo3List = $(InterruptList)
Combo3Out = $(InterruptIndex)
Combo4List = $(RingSpeedList)
Combo4Out = $(RingSpeedIndex)
ComboListItemsIn = {Combo1List, Combo2List, Combo3List, Combo4List}
ComboListItemsOut = {Combo1Out, Combo2Out, Combo3Out, Combo4Out}
RadioOptionGreyed = {}
CBOptionsGreyed = {}
NotifyFields = {NO, NO, NO, NO, NO}
HelpContext = $(ContextPCMCIASetupID)
;-----------------------------------------------------------------------
; MORE COMBO PARAMETER DIALOG
; ---------------------------
; This section sets up the PCMCIA parameter dialog. All textstrings
; presented in this dialog are defined here.
;
;-----------------------------------------------------------------------
[COMBOMoreDlgENG]
DlgType = "RadioCombination"
DlgTemplate = "COMBOM"
Caption = "Pc Card Setup"
DlgText = "Please select values for the following fields:"
Free = "&Advanced..."
Combo1Label = "I/O &Base Address:"
Combo2Label = "&Memory Window:"
Combo3Label = "&Interrupt:"
Combo4Label = "&Ring Speed:"
Combo5Label = "&Com Port:"
Combo1List = $(IOBasePCMCIAList)
Combo1Out = $(IOBasePCMCIAIndex)
Combo2List = $(MemWinList)
Combo2Out = $(MemWinIndex)
Combo3List = $(InterruptList)
Combo3Out = $(InterruptIndex)
Combo4List = $(RingSpeedList)
Combo4Out = $(RingSpeedIndex)
Combo5List = $(ComPortList)
Combo5Out = $(ComPortIndex)
ComboListItemsIn = {Combo1List, Combo2List, Combo3List, Combo4List, Combo5List}
ComboListItemsOut = {Combo1Out, Combo2Out, Combo3Out, Combo4Out, Combo5Out}
RadioOptionGreyed = {}
CBOptionsGreyed = {}
NotifyFields = {NO, NO, NO, NO, NO}
HelpContext = $(ContextPCMCIASetupID)
;-----------------------------------------------------------------------
; PCMCIA ADVANCED SETTINGS DIALOG
; -------------------------------
; This section sets up the PCMCIA adavanced settings dialog. All
; textstrings presented in this dialog are defined here.
;
;-----------------------------------------------------------------------
[PCMCIAAdvancedDlgENG]
DlgType = "RadioCombination"
DlgTemplate = "PCMCIAADV"
Caption = "Pc Card Advanced Settings"
DlgText = "Please select values for the following fields:"
Combo1Label = "Pc Card &Enabler:"
Combo2Label = "&Additional Waitstates:"
Radio1Label = "&Datasize:"
Radio1Button1 = *($(DatasizeLabels),1)
Radio1Button2 = *($(DatasizeLabels),2)
Combo1List = $(IOBasePCMCIAControllerList)
Combo1Out = $(IOBasePCMCIAControllerIndex)
Combo2List = $(WaitstateList)
Combo2Out = $(WaitstateIndex)
ComboListItemsIn = {Combo1List, Combo2List}
ComboListItemsOut = {Combo1Out, Combo2Out}
RadioIn = { $(DatasizeIndex) }
RadioOptionGreyed = {}
CBOptionsGreyed = {}
NotifyFields = {NO, NO, NO, NO, NO}
HelpContext = $(ContextPCMCIAAdvancedID)
;---------------------------------------------------------------------------
; 1. Identify
;
; DESCRIPTION: To verify that this INF deals with the same type of options
; as we are choosing currently.
;
; INPUT: None
;
; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL
; $($R1): Option Type (COMPUTER ...)
; $($R2): Diskette description
;---------------------------------------------------------------------------
[Identify]
read-syms Identification
set Status = STATUS_SUCCESSFUL
set Identifier = $(OptionType)
set Media = #("Source Media Descriptions", 1, 1)
Return $(Status) $(Identifier) $(Media)
;------------------------------------------------------------------------
; 2. ReturnOptions:
;
; DESCRIPTION: To return the option list supported by this INF and the
; localised text list representing the options.
;
;
; INPUT: $($0): Language used. ( ENG | FRN | ... )
;
; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL |
; STATUS_NOLANGUAGE
; STATUS_FAILED
; STATUS_NOTSUPPORTED
;
; $($R1): Option List
; $($R2): Option Text List
;------------------------------------------------------------------------
[ReturnOptions]
set Status = STATUS_FAILED
set OptionList = {}
set OptionTextList = {}
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) in $(LanguageList)
ifstr(i) $($1) == ""
goto returnoptions
endif
set PlatformList = ^(PlatformsSupported, 1)
Ifcontains(i) $($1) in $(PlatformList)
goto returnoptions
else
set Status = STATUS_NOTSUPPORTED
goto finish_ReturnOptions
endif
else
set Status = STATUS_NOLANGUAGE
goto finish_ReturnOptions
endif
returnoptions = +
set OptionList = ^(Options, 1)
set OptionTextList = ^(OptionsText$($0), 1)
set Status = STATUS_SUCCESSFUL
finish_ReturnOptions = +
Return $(Status) $(OptionList) $(OptionTextList)
;------------------------------------------------------------------------
;
; InstallOption:
;
; This section is shelled to by main installation processing
; or by NCPASHEL.INF during reconfig, removal, update, etc.
;
;
; FUNCTION: To copy files representing Options
; To configure the installed option
; To update the registry for the installed option
;
; INPUT: $($0): Language to use
; $($1): OptionID to install
; $($2): SourceDirectory
; $($3): AddCopy (YES | NO)
; $($4): DoCopy (YES | NO)
; $($5): DoConfig (YES | NO)
;
; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL |
; STATUS_NOLANGUAGE |
; STATUS_USERCANCEL |
; STATUS_FAILED
;
;------------------------------------------------------------------------
[InstallOption]
StartWait
set SrcDir = ""
set Option = $($1)
set SrcDir = $($2)
set AddCopy = $($3)
set DoCopy = $($4)
set DoConfig = $($5)
ifstr(i) $(SrcDir) == ""
Set SrcDir = "A:\"
Endif
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) NOT-IN $(LanguageList)
Return STATUS_NOLANGUAGE
endif
Debug-Output "STF_CWDDIR is: "$(!STF_CWDDIR)
Debug-Output "STF_LANGUAGE is: "$(!STF_LANGUAGE)
set-subst LF = "\n"
read-syms GeneralConstants
read-syms FileConstants
read-syms DialogConstants$(!STF_LANGUAGE)
ifstr(i) $(!NTN_Origination) == "NCPA"
set Continue = "OK"
endif
read-syms FileConstants$(!STF_LANGUAGE)
detect date
set-title $(FunctionTitle)
set to = Begin
set from = Begin
set CommonStatus = STATUS_SUCCESSFUL
SetHelpFile $(HelpfileName) $(ContextMinimumID) $(ContextMaximumID)
EndWait
Begin = +
;
; Get the Windows NT version. We will not install on NT v3.1x
;
set CurrentVersionValue = ""
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows Nt\CurrentVersion" $(!REG_KEY_READ) KeyNt
Ifstr(i) $(KeyNt) != ""
GetRegValue $(KeyNt) "CurrentVersion" CurrentVersionValue
Debug-Output "$(InfFile) $(Option): WinNT CurrentVersion ="$(CurrentVersionValue)
CloseRegKey $(KeyNt)
Endif
ifstr(i) (*($(CurrentVersionValue),4)) == ($(NT310VersionConstant))
Debug-Output "$(InfFile) $(Option): Configureadapter"
set Error = "Windows NT v3.10 is not support by this product"
goto fatal
endif
ifstr(i) (*($(CurrentVersionValue),4)) == ($(NT350VersionConstant))
; PCI Detect will be included in NT v3.51
Debug-Output "Running on WindowsNT 3.50"
set PCIDetectSupported = $(FALSE)
endif
set NTComboSupport = $(FALSE)
ifstr(i) (*($(CurrentVersionValue),4)) == ($(NT40VersionConstant))
set NTComboSupport = $(TRUE)
endif
;
; Supply backwards compatibility for INF file
;
ifstr(i) $(Option) == "OCTK16"
set Option = OCTK3118
else-ifstr(i) $(Option) == "PCMCIA"
set Option = OCTK3221
else-ifstr(i) $(Option) == "COMBO"
set Option = OCTK3232
endif
Ifstr(i) $(!NTN_InstallMode) == deinstall
set StartLabel = removeadapter
else-Ifstr(i) $(!NTN_InstallMode) == Update
set StartLabel = UpgradeSoftware
else-Ifstr(i) $(!NTN_InstallMode) == bind
set StartLabel = bindingadapter
else-Ifstr(i) $(!NTN_InstallMode) == configure
set StartLabel = configureadapter
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Debug-Output "Cannot configure the driver software."
Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error: cannot get an error string."
goto ShellCodeError
endif
set Error = $($R0)
set from = end
set to = end
goto nonfatalinfo
endif
else
set StartLabel = installadapter
set OEM_ABANDON_OPTIONS = {}
set OEM_ABANDON_SOFTWARE = FALSE
set OEM_ABANDON_ON = TRUE
endif
set IOBaseAddrIndex = *($(IOBaseAddrList), 1)
set RcvBufCountIndex = *($(RcvBufCountList), 27)
set XmitBufCountIndex = *($(XmitBufCountList), 25)
set FrameSizeIndex = *($(FrameSizeList), 12)
set NetworkAddress = *($(EditTextOut), 1)
set Rad1 = 1
set Rad2 = 3
set RadioIn = {$(Rad1), $(Rad2) }
set EarlyRelease = "Yes"
set FrameStatus = "Yes"
set IOBasePCMCIAIndex = *($(IOBasePCMCIAList), $(IOBasePCMCIADefault))
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters\SerialOctk16" $(MAXIMUM_ALLOWED) SerialHandle
ifstr $(SerialHandle) == $(KeyNull)
set ComPortIndex = *($(ComPortList), $(ComPortDefault))
set AllowComPort = $(TRUE)
else
set ComPortIndex = *($(ComPortList), 6)
set AllowComPort = $(FALSE)
endif
CloseRegKey $(SerialHandle)
set InterruptIndex = *($(InterruptList), $(InterruptDefault))
set MemWinIndex = *($(MemWinList), $(MemWinDefault))
set IOBasePCMCIAControllerIndex = *($(IOBasePCMCIAControllerList), 1)
ifcontains(i) $(Option) in {"OCTK3220","OCTK3221"}
set IOBasePCMCIAControllerList = >($(IOBasePCMCIAControllerList),"Windows NT Enabler")
set IOBasePCMCIAControllerValues = >($(IOBasePCMCIAControllerValues),0)
set IOBasePCMCIAControllerIndex = *($(IOBasePCMCIAControllerList), 3)
endif
ifcontains(i) $(Option) in {"OCTK3230","OCTK3232"}
ifstr(i) $(NTComboSupport) == $(TRUE)
set IOBasePCMCIAControllerList = >($(IOBasePCMCIAControllerList),"Windows NT Enabler")
set IOBasePCMCIAControllerValues = >($(IOBasePCMCIAControllerValues),0)
set IOBasePCMCIAControllerIndex = *($(IOBasePCMCIAControllerList), 3)
endif
endif
set WaitstateIndex = *($(WaitstateList), 1)
set DatasizeIndex = 1
set RingSpeedIndex = *($(RingSpeedList), 1)
set RSIndex = *($(RSList), 1)
Shell "" DebugConfiguration "After parameter querying"
set RcvBufCountValue = *($(RcvBufCountList), ~($(RcvBufCountValues),6))
set XmitBufCountValue = *($(XmitBufCountList), ~($(XmitBufCountValues),8))
set FrameSizeValue = *($(FrameSizeList), ~($(FrameSizeValues),4096))
set BusNumber = $(BusNoDefault)
set SlotNumber = $(SlotNoDefault)
Shell $(UtilityInf), GetBusTypeNum
set BusInterfaceType = $($R1)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
Set from = $(fatal)
Set to = $(fatal)
Goto $(StartLabel)
;-----------------------------------------------
; Installation Section
;-----------------------------------------------
;
; Get the current values of all the parameters
;
installadapter = +
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
CloseRegKey $(KeyProduct)
ifstr(i) !(NTN_RegBase) == $(ProductKeyName)
Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+
$(ProductVersion)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error: cannot get an error string."
goto ShellCodeError
endif
goto end
else
set OldVersionExisted = $(TRUE)
endif
endif
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) NO
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
Set SrcDir = $($R1)
install "Install-Dll"
Goto adapteroptions
;-----------------------------------------------
; Configuration Section
;-----------------------------------------------
;
; Get the current values of all the parameters
;
configureadapter = +
Ifstr(i) $(KeyProduct) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) == $(KeyNull)
set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
Debug-Output "Cannot find component product key"
goto fatalregistry
Endif
Endif
Debug-Output "INF: Shelling to FindService"
Shell $(UtilityInf) FindService, $(KeyProduct)
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "INF: FindService shell failure"
Goto ShellCodeError
Endif
Ifstr(i) $($R0) != NO_ERROR
Debug-Output "INF: FindService Shell error: "$($R0)
Goto fatalregistry
endif
Set KeyParameters = $($R2)
CloseRegKey $($R1)
Ifstr $(KeyParameters) == $(KeyNull)
set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
Debug-Output "Cannot find component service"
goto fatalregistry
endif
set OldVersionExisted = $(TRUE)
set ValueName = ""
set ValueData = ""
set ValueStr = ""
set ValueList = {}
EnumRegValue $(KeyParameters) ValueList
ForListDo $(ValueList)
set ValueItem = $($)
set ValueName = *($(ValueItem),1)
set ValueData = *($(ValueItem),4)
ifstr(i) $(ValueName) == "RecBufCount"
set RcvBufCountValue = $(ValueData)
else-ifstr(i) $(ValueName) == "IoBase"
set IOBaseAddrValue = $(ValueData)
else-ifstr(i) $(ValueName) == "TransmitBufferCount"
set XmitBufCountValue = $(ValueData)
else-ifstr(i) $(ValueName) == "TransmitBufferSize"
set FrameSizeValue = $(ValueData)
else-ifstr(i) $(ValueName) == "BusNumber"
set BusNumber = $(ValueData)
else-ifstr(i) $(ValueName) == "SlotNumber"
set SlotNumber = $(ValueData)
else-ifstr(i) $(ValueName) == "EarlyRelease"
set EarlyRelease = $(ValueData)
else-ifstr(i) $(ValueName) == "FrameStatus"
set FrameStatus = $(ValueData)
else-Ifstr(i) $(ValueName) == "NetworkAddress"
set NetworkAddress = $(ValueData)
else-ifstr(i) $(ValueName) == "IoBaseAddress"
set IOBasePCMCIAValue = $(ValueData)
else-ifstr(i) $(ValueName) == "IoBaseAddress_1"
set IOBasePCMCIAValue_1 = $(ValueData)
else-ifstr(i) $(ValueName) == "PCCARDAttributeMemoryAddress"
set MemWinValue = $(ValueData)
else-ifstr(i) $(ValueName) == "InterruptNumber"
set InterruptValue = $(ValueData)
else-ifstr(i) $(ValueName) == "ComPortBase"
set ComPortValue = $(ValueData)
ifstr(i) $(ComPortValue) != 0
set AllowComPort = $(TRUE)
endif
else-ifstr(i) $(ValueName) == "PcmciaCtrlBase"
set IOBasePCMCIAControllerValue = $(ValueData)
else-ifstr(i) $(ValueName) == "WaitStates"
set WaitstateValue = $(ValueData)
else-ifstr(i) $(ValueName) == "DataSize"
set DatasizeValue = $(ValueData)
else-ifstr(i) $(ValueName) == "RingSpeed"
set RingSpeedValue = $(ValueData)
else-ifstr(i) $(ValueName) == "BusType"
set BusInterfaceType = $(ValueData)
endif
EndForListDo
;
; For combo cards with NT enabler we must
; use the second I/O window
;
ifstr(i) $(IOBasePCMCIAValue_1) != ""
set IOBasePCMCIAValue = $(IOBasePCMCIAValue_1)
endif
;
; Combo-lists and radio-buttons use a special list of parameter-names
; when dialogs are executed. The following section converts the actual
; values into the corresponding names (indexes). If a value is undefined,
; the first entry in the index-list is used.
;
set RcvBufCountIndex = *($(RcvBufCountList), ~($(RcvBufCountValues),$(RcvBufCountValue)))
ifstr(i) $(RcvBufCountIndex) == ""
set RcvBufCountIndex = *($(RcvBufCountList), 27)
endif
set XmitBufCountIndex = *($(XmitBufCountList), ~($(XmitBufCountValues),$(XmitBufCountValue)))
ifstr(i) $(XmitBufCountIndex) == ""
set XmitBufCountIndex = *($(XmitBufCountList), 25)
endif
set FrameSizeIndex = *($(FrameSizeList), ~($(FrameSizeValues),$(FrameSizeValue)))
ifstr(i) $(FrameSizeIndex) == ""
set FrameSizeIndex = *($(FrameSizeList), 3)
endif
set IOBaseAddrIndex = *($(IOBaseAddrList), ~($(IOBaseAddrValues),$(IOBaseAddrValue)))
ifstr(i) $(IOBaseAddrIndex) == ""
set IOBaseAddrIndex = *($(IOBaseAddrList), 1)
endif
ifcontains(i) $(Option) in {"OCTK3117","OCTK3118","OCTK3133","OCTK3129","OCTK3136","OCTK3137"}
set RSIndex = *($(RSList), ~($(RSValues),$(RingSpeedValue)))
ifstr(i) $(RSIndex) == ""
set RSIndex = *($(RSList), 1)
endif
else
set RingSpeedIndex = *($(RingSpeedList), ~($(RingSpeedValues),$(RingSpeedValue)))
ifstr(i) $(RingSpeedIndex) == ""
set RingSpeedIndex = *($(RingSpeedList), 1)
endif
endif
Ifstr(i) $(EarlyRelease) == "Yes"
set Rad1 = 1
else
set Rad1 = 2
endif
Ifstr(i) $(FrameStatus) == "Yes"
set Rad2 = 3
else
set Rad2 = 4
endif
set RadioIn = {$(Rad1), $(Rad2) }
set IOBasePCMCIAIndex = *($(IOBasePCMCIAList), ~($(IOBasePCMCIAValues),$(IOBasePCMCIAValue)))
ifstr(i) $(IOBasePCMCIAIndex) == ""
set IOBasePCMCIAIndex = *($(IOBasePCMCIAList), 1)
endif
set MemWinIndex = *($(MemWinList), ~($(MemWinValues),$(MemWinValue)))
ifstr(i) $(MemWinIndex) == ""
set MemWinIndex = *($(MemWinList), 49)
endif
set InterruptIndex = *($(InterruptList), ~($(InterruptValues),$(InterruptValue)))
ifstr(i) $(InterruptIndex) == ""
set InterruptIndex = *($(InterruptList), 3)
endif
set ComPortIndex = *($(ComPortList), ~($(ComPortValues),$(ComPortValue)))
ifstr(i) $(ComPortIndex) == ""
set ComPortIndex = *($(ComPortList), 6)
endif
set IOBasePCMCIAControllerIndex = *($(IOBasePCMCIAControllerList), ~($(IOBasePCMCIAControllerValues),$(IOBasePCMCIAControllerValue)))
ifstr(i) $(IOBasePCMCIAControllerIndex) == ""
set IOBasePCMCIAControllerIndex = *($(IOBasePCMCIAControllerList), 1)
endif
set WaitstateIndex = *($(WaitstateList), ~($(WaitstateValues),$(WaitstateValue)))
ifstr(i) $(WaitstateIndex) == ""
set WaitstateIndex = *($(WaitstateList), 2)
endif
set DatasizeIndex = *($(DatasizeList), ~($(DatasizeValues),$(DatasizeValue)))
ifstr(i) $(DatasizeIndex) == ""
set DatasizeIndex = *($(DatasizeList), 1)
endif
;
; This section runs the dialogs. From the main dialog (adapter parameter
; setup) it is possible to enter the PCMCIA dialog if requested. When
; exiting the PCMCIA dialog the user is returned to the main dialog.
;
adapteroptions = +
set from = adapteroptions
ifstr(i) $(!NTN_InstallMode) == "install"
;
; Default parameters for installation.
; User will NOT be asked to change/verify configuration during
; normal or unattended installation, unless we are installing on
; NT v3.50.
;
ifint $(PCIDetectSupported) == $(FALSE)
ifstr(i) $(!AutoNetBusNumber) != ""
set BusNumber = $(!AutoNetBusNumber)
else
set BusNumber = $(BusNoDefault)
endif
else
; We will not ask user for configuration during installation
; if PCI detection is supported
goto unattended
endif
ifstr(i) $(!STF_GUI_UNATTENDED) == "YES"
; Default parameters for unattended installation
goto unattended
endif
endif
set OldNetAddress = $(NetworkAddress)
;
; Load DLL containing dialogs and verification routines
;
LoadLibrary "Olicom Driver Disk" $(DialogDllName) DialogHandle
adapteroptions1 = +
;
; Read main dialog setup and show dialog
;
ifcontains(i) $(Option) in {"OCTK3117","OCTK3118","OCTK3133","OCTK3129","OCTK3136","OCTK3137"}
read-syms OCTK16ParameterDlg$(!STF_LANGUAGE)
endif
ifcontains(i) $(Option) in {"OCTK3220","OCTK3221"}
read-syms PCMCIAParameterDlg$(!STF_LANGUAGE)
endif
ifcontains(i) $(Option) in {"OCTK3230","OCTK3232"}
read-syms COMBOParameterDlg$(!STF_LANGUAGE)
endif
set RadioIn = {$(Rad1), $(Rad2) }
ui start "InputDlg" $(DialogHandle)
ui pop 1
;
; Save new settings because this dialog might be called again.
; If CANCEL was pressed these values will not be used
;
ifcontains(i) $(Option) in {"OCTK3117","OCTK3118","OCTK3133","OCTK3129","OCTK3136","OCTK3137"}
set IOBaseAddrIndex = $(Combo1Out)
set RcvBufCountIndex = $(Combo2Out)
set XmitBufCountIndex = $(Combo3Out)
set FrameSizeIndex = $(Combo4Out)
set RSIndex = $(Combo5Out)
else
set RcvBufCountIndex = $(Combo1Out)
set XmitBufCountIndex = $(Combo2Out)
set FrameSizeIndex = $(Combo3Out)
Endif
IfContains "1" IN $(RadioOut)
set EarlyRelease = "Yes"
set Rad1 = 1
else-IfContains "2" IN $(RadioOut)
set EarlyRelease = "No"
set Rad1 = 2
endif
IfContains "3" IN $(RadioOut)
set FrameStatus = "Yes"
set Rad2 = 3
else-IfContains "4" IN $(RadioOut)
set FrameStatus = "No"
set Rad2 = 4
endif
set NetworkAddress = *($(EditTextOut),1)
ifstr(i) $(DLGEVENT) == "CONTINUE"
;
; parameters have already been stored at this stage
;
goto nextstep
else-ifstr(i) $(DLGEVENT) == "EXIT"
set CommonStatus = STATUS_USERCANCEL
Debug-Output "Action: exit. Bye."
FreeLibrary $(DialogHandle)
goto end
else-ifstr(i) $(DLGEVENT) == "FREEBUTTON1" ; BUS... (non PCMCIA)
adapteroptions2 = +
;
; Read PCMCIA dialog setup and show dialog
;
ifcontains(i) $(Option) in {"OCTK3220","OCTK3221"}
read-syms PCMCIAMoreDlg$(!STF_LANGUAGE)
else-ifcontains(i) $(Option) in {"OCTK3230","OCTK3232"}
ifstr $(AllowComPort) == $(TRUE)
read-syms COMBOMoreDlg$(!STF_LANGUAGE)
else
read-syms PCMCIAMoreDlg$(!STF_LANGUAGE)
endif
else-ifcontains(i) $(Option) in {"OCTK3117","OCTK3118","OCTK3133","OCTK3129"}
Shell $(UtilityInf),GetBusTypeDialog,$(ProductHardwareDescription) $(BusInterfaceType) $(BusNumber)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto Shell_Code_Error
endif
ifstr(i) $($R0) == ERROR
Shell $(UtilityInf), GetBusTypeNum
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto Shell_Code_Error
endif
set BusInterfaceType = $($R1)
set BusNumber = 0
else
set BusInterfaceType = $($R1)
set BusNumber = $($R2)
endif
set BusTypeConfigured = 1
goto adapteroptions1
else-ifcontains(i) $(Option) in {"OCTK3136","OCTK3137"}
ifint $(PCIDetectSupported) == $(FALSE)
Shell $(UtilityInf),GetBusTypeDialog,$(ProductHardwareDescription) $(BusInterfaceType) $(BusNumber)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto Shell_Code_Error
endif
ifstr(i) $($R0) == ERROR
Shell $(UtilityInf), GetBusTypeNum
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto Shell_Code_Error
endif
set BusInterfaceType = $($R1)
set BusNumber = 0
else
set BusInterfaceType = $($R1)
set BusNumber = $($R2)
endif
else
Shell $(subroutineinf) SetupMessage $(!STF_LANGUAGE) STATUS +
"Bus parameters are configured automatically for PCI adapters"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto Shell_Code_Error
endif
endif
set BusTypeConfigured = 1
goto adapteroptions1
endif
ui start "InputDlg" $(DialogHandle)
ui pop 1
;
; Save new settings because this dialog might be called again.
; If CANCEL was pressed these values will not be used
;
set IOBasePCMCIAIndex = $(Combo1Out)
set MemWinIndex = $(Combo2Out)
set InterruptIndex = $(Combo3Out)
set RingSpeedIndex = $(Combo4Out)
set ComPortIndex = $(Combo5Out)
ifstr(i) $(DLGEVENT) == "CONTINUE"
;
; parameters have already been stored at this stage
;
goto adapteroptions1
else-ifstr(i) $(DLGEVENT) == "FREEBUTTON1"
;
; Read PCMCIA Advanced dialog setup and show dialog
;
read-syms PCMCIAAdvancedDlg$(!STF_LANGUAGE)
ui start "InputDlg" $(DialogHandle)
ui pop 1
;
; Save new settings because this dialog might be called again.
; If CANCEL was pressed these values will not be used
;
set IOBasePCMCIAControllerIndex = $(Combo1Out)
set WaitstateIndex = $(Combo2Out)
set DatasizeIndex = *($(RadioOut),1)
goto adapteroptions2
else
Debug-Output "Action: unknown: "$(DLGEVENT)
FreeLibrary $(DialogHandle)
goto end
endif
else
Debug-Output "Action: unknown: "$(DLGEVENT)
FreeLibrary $(DialogHandle)
goto end
endif
nextstep =+
ifcontains(i) $(Option) in {"OCTK3136","OCTK3137"}
set BusTypeConfigured = 1 ; Avoid BusType/BusNumber Dialog box for PCI
endif
ifstr(i) $(!NTN_InstallMode) == "install"
ifint $(BusTypeConfigured) == 0
ifcontains(i) $(Option) in {"OCTK3117","OCTK3118","OCTK3133","OCTK3129","OCTK3136","OCTK3137"}
Shell $(UtilityInf),GetBusTypeDialog,$(ProductHardwareDescription) $(BusInterfaceType) $(BusNumber)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto Shell_Code_Error
endif
ifstr(i) $($R0) == ERROR
Shell $(UtilityInf), GetBusTypeNum
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto Shell_Code_Error
endif
set BusInterfaceType = $($R1)
set BusNumber = 0
else
set BusInterfaceType = $($R1)
set BusNumber = $($R2)
endif
endif
endif
endif
ifstr $(NetworkAddress) != ""
;
; If network address has been entered then verify that it is a
; valid address (not a multicast or broadcast address)
;
set FLibraryErrCtl = 1
LibraryProcedure DlgResult $(DialogHandle) VerifyAddress $(NetworkAddress)
set FLibraryErrCtl = 0
ifstr $(DlgResult) != "STATUS_SUCCESS"
FreeLibrary $(DialogHandle)
set Error = $(DlgResult)
goto nonfatal
endif
endif
set FLibraryErrCtl = 1
set RcvBufCountValue = *($(RcvBufCountValues), ~($(RcvBufCountList),$(RcvBufCountIndex)))
set XmitBufCountValue = *($(XmitBufCountValues), ~($(XmitBufCountList),$(XmitBufCountIndex)))
set FrameSizeValue = *($(FrameSizeValues), ~($(FrameSizeList),$(FrameSizeIndex)))
set RingSpeedValue = *($(RingSpeedValues), ~($(RingSpeedList),$(RingSpeedIndex)))
set RSValue = *($(RSValues), ~($(RSList),$(RSIndex)))
ifcontains(i) $(Option) in {"OCTK3117","OCTK3118","OCTK3133","OCTK3129","OCTK3136","OCTK3137"}
LibraryProcedure DlgResult $(DialogHandle) CheckMaxFrameSize $(FrameSizeValue) $(XmitBufCountValue) $(RcvBufCountValue) $(RSValue)
else
LibraryProcedure DlgResult $(DialogHandle) CheckMaxFrameSize $(FrameSizeValue) $(XmitBufCountValue) $(RcvBufCountValue) $(RingSpeedValue)
endif
set FLibraryErrCtl = 0
ifstr $(DlgResult) != "STATUS_SUCCESS"
FreeLibrary $(DialogHandle)
set Error = $(DlgResult)
goto nonfatal
endif
FreeLibrary $(DialogHandle)
unattended =+
ifint $(OldVersionExisted) == $(TRUE)
ifstr(i) $(!NTN_InstallMode) == configure
goto writeparameters
endif
endif
StartWait
Ifint $(OldVersionExisted) != $(FALSE)
Goto installhardware
Endif
ifstr(i) $(!NTN_InstallMode) == "install"
Ifstr(i) $(DoCopy) == "YES"
Ifstr(i) $(SrcDir) == ""
read-syms AskSourceDlgText
Shell $(subroutineinf) DoAskSourceEx $(SrcDir) $(DlgText)
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
Set SrcDir = $($R1)
Endif
Endif
install "Install-Option"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
endif
endif
Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), +
$(ProductSoftwareName), +
$(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), +
$(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+
$(NetEventDLL), ""
Set OEM_ABANDON_SOFTWARE = TRUE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "OEMNADUB.INF: Registry error: add software components"
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
CloseRegKey $($R4)
CloseRegKey $($R5)
goto fatalregistry
endif
set SoftProductKey = $($R1)
Set SoftNetRuleKey = $($R2)
Set SoftServiceKey = $($R3)
Set SoftParameterKey = $($R4)
Set SoftLinkageKey = $($R5)
set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+
{MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+
{MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+
{Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(SoftProductKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Registry error: add value list."
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftParameterKey)
CloseRegKey $(SoftLinkageKey)
goto fatalregistry
endif
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+
{use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, +
{bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, +
{bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareBindable)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(SoftNetRuleKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftParameterKey)
CloseRegKey $(SoftLinkageKey)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Registry error: add value list."
goto fatalregistry
endif
;
; Insert hardware component in registry
;
installhardware =+
Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)
ifint $($R4) != -1
Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
endif
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "Cannot add hardware component"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Registry error: add hardware component"
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
goto fatalregistry
endif
set KeyProduct = $($R1)
set KeyAdapterRules = $($R2)
set KeyParameters = $($R3)
set AdapterNumber = $($R4)
set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+
{Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+
{ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
CloseRegKey $(KeyProduct)
Set KeyProduct = ""
set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardwareType)},+
{bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardwareClass)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(KeyAdapterRules), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
CloseRegKey $(KeyAdapterRules)
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Registry error: add value list."
CloseRegKey $(KeyParameters)
goto fatalregistry
endif
;
; Write Adapter Parameters to registry
;
writeparameters = +
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
Ifstr(i) $(KeyParameters) == $(KeyNull)
Debug-Output "*** KeyParameters is NULL at writeparameters"
Endif
;
; Convert selections from combo-lists and radio-buttons into actual
; parameter values
;
set IOBaseAddrValue = *($(IOBaseAddrValues), ~($(IOBaseAddrList),$(IOBaseAddrIndex)))
set RcvBufCountValue = *($(RcvBufCountValues), ~($(RcvBufCountList),$(RcvBufCountIndex)))
set XmitBufCountValue = *($(XmitBufCountValues), ~($(XmitBufCountList),$(XmitBufCountIndex)))
set FrameSizeValue = *($(FrameSizeValues), ~($(FrameSizeList),$(FrameSizeIndex)))
set IOBasePCMCIAValue = *($(IOBasePCMCIAValues), ~($(IOBasePCMCIAList),$(IOBasePCMCIAIndex)))
set MemWinValue = *($(MemWinValues), ~($(MemWinList),$(MemWinIndex)))
set InterruptValue = *($(InterruptValues), ~($(InterruptList),$(InterruptIndex)))
set RingSpeedValue = *($(RingSpeedValues), ~($(RingSpeedList),$(RingSpeedIndex)))
set RSValue = *($(RSValues), ~($(RSList),$(RSIndex)))
set ComPortValue = *($(ComPortValues), ~($(ComPortList),$(ComPortIndex)))
set IOBasePCMCIAControllerValue = *($(IOBasePCMCIAControllerValues), ~($(IOBasePCMCIAControllerList),$(IOBasePCMCIAControllerIndex)))
set WaitstateValue = *($(WaitstateValues), ~($(WaitstateList),$(WaitstateIndex)))
set DatasizeValue = *($(DatasizeValues), ~($(DatasizeList),$(DatasizeIndex)))
ifcontains(i) $(Option) in {"OCTK3230","OCTK3232"}
set BusInterfaceType = 1
set BusNumber = 0
Endif
ifcontains(i) $(Option) in {"OCTK3220","OCTK3221"}
set BusInterfaceType = 1
set BusNumber = 0
Endif
ifcontains(i) $(Option) in {"OCTK3230","OCTK3232"}
;
; If we're installing a ComboCard, update settings for Serial\parameters\serialoctk16 as well
; SERIALCOMM will be created automatically by serial.sys
;
ifint $(ComPortValue) != 0
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters\SerialOctk16" $(MAXIMUM_ALLOWED) SerialHandle
Ifstr $(SerialHandle) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) SerialKey
CreateRegKey $(SerialKey) {"SerialOctk16",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" SerialHandle
CloseRegKey $(SerialKey)
endif
ifint $(ComPortValue) != 24
set NewValueList = {{DosDevices, $(NoTitle),$(!REG_VT_SZ), $(ComPortIndex)},+
{ForceFifoEnable, $(NoTitle),$(!REG_VT_DWORD), 0},+
{ForceShare, $(NoTitle),$(!REG_VT_DWORD), 1},+
{Interrupt, $(NoTitle),$(!REG_VT_DWORD), $(InterruptValue)},+
{PortAddress, $(NoTitle),$(!REG_VT_DWORD), $(ComPortValue)}}
Else
set-add ComportBaseAddress = $(ComPortValue), $(IOBasePCMCIAValue)
set NewValueList = {{DosDevices, $(NoTitle),$(!REG_VT_SZ), $(ComPortIndex)},+
{ForceFifoEnable, $(NoTitle),$(!REG_VT_DWORD), 0},+
{ForceShare, $(NoTitle),$(!REG_VT_DWORD), 1},+
{Interrupt, $(NoTitle),$(!REG_VT_DWORD), $(InterruptValue)},+
{PortAddress, $(NoTitle),$(!REG_VT_DWORD), $(ComportBaseAddress)}}
Endif
Shell $(UtilityInf), AddValueList, $(SerialHandle), $(NewValueList)
CloseRegKey $(SerialHandle)
;
; Update settings comm port in SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports section
;
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports" $(MAXIMUM_ALLOWED) SerialHandle
Ifstr $(SerialHandle) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion" $(MAXIMUM_ALLOWED) SerialKey
CreateRegKey $(SerialKey) {"Ports",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" SerialHandle
CloseRegKey $(SerialKey)
endif
SetRegValue $(SerialHandle) {$(ComPortIndex)":",$(NoTitle),$(!REG_VT_SZ), "9600,n,8,1"}
CloseRegKey $(SerialHandle)
;
; Update settings in HARDWARE\DEVICEMAP\SERIALCOMM section
;
OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP\SERIALCOMM" $(MAXIMUM_ALLOWED) SerialHandle
Ifstr $(SerialHandle) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP" $(MAXIMUM_ALLOWED) SerialKey
CreateRegKey $(SerialKey) {"SERIALCOMM",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" SerialHandle
CloseRegKey $(SerialKey)
endif
SetRegValue $(SerialHandle) {"SerialOctk16",$(NoTitle),$(!REG_VT_SZ),$(ComPortIndex)}
CloseRegKey $(SerialHandle)
Else
;
; Be nice and delete the COM stuff if user really wants so
; SERIALCOMM will be deleted automatically
;
ifstr(i) $(AllowComPort) == $(TRUE)
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) SerialHandle
DeleteRegTree $(SerialHandle) "SerialOctk16"
CloseRegKey $(SerialHandle)
OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP\SERIALCOMM" $(MAXIMUM_ALLOWED) SerialHandle
DeleteRegValue $(SerialHandle) "SerialOctk16"
CloseRegKey $(SerialHandle)
endif
Endif
Endif
ifcontains(i) $(Option) in {"OCTK3136","OCTK3137"}
;
; If We are installing a PCI adapter so go get PCI information
;
ifint $(PCIDetectSupported) == $(FALSE)
;
; If auto-detect is not supported then use values from dialogbox
;
else-ifstr(i) $(!NTN_InstallMode) == "install"
;
; NOTE: PCI configuration (BusNumber, SlotNumber will not be
; changed in normal configuration
;
set DetectedBusNumber = $(BusNumber)
set DetectedSlotNumber = $(SlotNumber)
set VendorID = 4237 ; Olicom Vendor ID: 108Dh
set DeviceID = 1 ; OC-3136/OC-3137
; Flag adapter already installed, i.e. do not do another installation
Set InstalledAdapter = "YES"
; Get PCI information
Shell $(UtilityInf), GetPCIInformation, $(VendorID) $(DeviceID)
set AdapterList = $($R0)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R0) == {}
;
; Adapter list is empty. No adapters of this type was found
;
ifstr(i) $(!STF_GUI_UNATTENDED) != "YES"
;
; Unattended install: We will NOT install adapter
; Attended install : We will ask user if he wants to install
; adapter anyway.
;
shell "subroutn.inf" SetupMessage, $(!STF_LANGUAGE), WARNING,+
"No PCI adapters found. Install anyway?"
ifstr(i) $($R0) != STATUS_SUCCESSFUL
set Error = $($R0)
goto fatal
endif
ifstr(i) $($R1) == "OK"
Set DetectedBusNumber = $(BusNoDefault)
Set DetectedSlotNumber = $(SlotNoUnknown)
Set InstalledAdapter = "NO"
endif
endif
else
;
; Adapter(s) has be found. We will try to find out if the (or
; these) adapter hasn't been installed already.
;
ForListDo $(AdapterList)
; Run through the Adapter list
; Get Bus number from list:
set TestBusNumber = *($($),1)
; Get SLot Number from list:
set TestSlotNumber = *($($),2)
; Check registry
Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(TestBusNumber), +
$(TestSlotNumber), $(ProductHardware$(Option)Description), $(ProductHardwareName)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr $($R0) != "NO_ERROR"
set Error = $($R0)
goto fatal
endif
ifstr(i) $($R1) == "NO"
; This adapter in the AdapterList has not been install yet
ifstr(i) $(InstalledAdapter) == "YES"
; We can not Break from ForListDo, so we will
; just flag that we have found an adapter to install
Set InstalledAdapter = "NO"
set DetectedBusNumber = $(TestBusNumber)
set DetectedSlotNumber = $(TestSlotNumber)
endif
endif
EndForListDo
ifstr(i) $(InstalledAdapter) == "YES"
;
; We did not find any un-installed adapter
;
ifstr(i) $(!STF_GUI_UNATTENDED) != "YES"
;
; Unattended install: We will NOT install adapter
; Attended install : We will ask user if he wants to install
; adapter anyway.
;
shell "subroutn.inf" SetupMessage, $(!STF_LANGUAGE), WARNING,+
"Adapter already installed. Install anyway?"
ifstr(i) $($R0) != STATUS_SUCCESSFUL
set Error = $($R0)
goto fatal
endif
ifstr(i) $($R1) == "OK"
Set DetectedBusNumber = $(BusNoDefault)
Set DetectedSlotNumber = $(SlotNoUnknown)
Set InstalledAdapter = "NO"
endif
endif
endif
endif
Set BusNumber = $(DetectedBusNumber)
Set SlotNumber = $(DetectedSlotNumber)
ifstr(i) $(InstalledAdapter) == "YES"
;
; We will NOT install the adapter
; Delete what has already been added to the registry.
;
EndWait
goto abandon
endif
endif
else
;
; Leave BusNumber and SlotNumber for non-PCI devices
;
endif
;
; If using NT enabler for combo cards we must request
; one additional I/O window
;
set PcmciaIoLength = 31
ifcontains(i) $(Option) in {"OCTK3230","OCTK3232"}
ifstr(i) $(NTComboSupport) == $(TRUE)
ifint $(IOBasePCMCIAControllerValue) == 0
set IOBasePCMCIAValue_1 = $(IOBasePCMCIAValue)
set PcmciaIoLength_1 = $(PcmciaIoLength)
set IOBasePCMCIAValue = $(ComPortValue)
set PcmciaIoLength = 8
endif
endif
endif
;
; Set up parameter list for AddValueList routine
;
Set NewValueList = {{IoBase,$(NoTitle),$(!REG_VT_DWORD),$(IOBaseAddrValue)},+
{MediaType,$(NoTitle),$(!REG_VT_DWORD),2},+
{BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusInterfaceType)},+
{BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNumber)},+
{SlotNumber,$(NoTitle),$(!REG_VT_DWORD),$(SlotNumber)},+
{RecBufCount,$(NoTitle),$(!REG_VT_DWORD),$(RcvBufCountValue)},+
{TransmitBufferCount,$(NoTitle),$(!REG_VT_DWORD),$(XmitBufCountValue)},+
{TransmitBufferSize,$(NoTitle),$(!REG_VT_DWORD),$(FrameSizeValue)},+
{EarlyRelease,$(NoTitle),$(!REG_VT_SZ),$(EarlyRelease)},+
{FrameStatus,$(NoTitle),$(!REG_VT_SZ),$(FrameStatus)},+
{IoBaseAddress,$(NoTitle),$(!REG_VT_DWORD),$(IOBasePCMCIAValue)},+
{IoLength,$(NoTitle),$(!REG_VT_DWORD),$(PcmciaIoLength)},+
{PCCARDAttributeMemoryAddress,$(NoTitle),$(!REG_VT_DWORD),$(MemWinValue)},+
{PCCARDAttributeMemorySize, $(NoTitle),$(!REG_VT_DWORD),4096},+
{PCCARDAttributeMemoryOffset, $(NoTitle),$(!REG_VT_DWORD),0},+
{InterruptNumber,$(NoTitle),$(!REG_VT_DWORD),$(InterruptValue)},+
{ComPortBase,$(NoTitle),$(!REG_VT_DWORD),$(ComPortValue)},+
{PcmciaCtrlBase,$(NoTitle),$(!REG_VT_DWORD),$(IOBasePCMCIAControllerValue)},+
{WaitStates,$(NoTitle),$(!REG_VT_DWORD),$(WaitstateValue)},+
{DataSize,$(NoTitle),$(!REG_VT_DWORD),$(DatasizeValue)}}
ifstr $(NetworkAddress) != ""
set NewValueList = >($(NewValueList),{NetworkAddress,$(NoTitle),$(!REG_VT_SZ),$(NetworkAddress)})
endif
ifcontains(i) $(Option) in {"OCTK3117","OCTK3118","OCTK3133","OCTK3129","OCTK3136","OCTK3137"}
set NewValueList = >($(NewValueList),{RingSpeed,$(NoTitle),$(!REG_VT_DWORD),$(RSValue)})
else
set NewValueList = >($(NewValueList),{RingSpeed,$(NoTitle),$(!REG_VT_DWORD),$(RingSpeedValue)})
ifcontains(i) $(Option) in {"OCTK3230","OCTK3232"}
ifstr(i) $(NTComboSupport) == $(TRUE)
ifint $(IOBasePCMCIAControllerValue) == 0
set NewValueList = >($(NewValueList),{Pcmcia,$(NoTitle),$(!REG_VT_DWORD),1})
set NewValueList = >($(NewValueList),{ModemFunction,$(NoTitle),$(!REG_VT_DWORD),1})
set NewValueList = >($(NewValueList),{IoBaseAddress_1,$(NoTitle),$(!REG_VT_DWORD),$(IOBasePCMCIAValue_1)})
set NewValueList = >($(NewValueList),{IoLength_1,$(NoTitle),$(!REG_VT_DWORD),$(PcmciaIoLength_1)})
else
set NewValueList = >($(NewValueList),{Pcmcia,$(NoTitle),$(!REG_VT_DWORD),0})
endif
else
set NewValueList = >($(NewValueList),{Pcmcia,$(NoTitle),$(!REG_VT_DWORD),0})
endif
else
ifint $(IOBasePCMCIAControllerValue) == 0
set NewValueList = >($(NewValueList),{Pcmcia,$(NoTitle),$(!REG_VT_DWORD),1})
else
set NewValueList = >($(NewValueList),{Pcmcia,$(NoTitle),$(!REG_VT_DWORD),0})
endif
endif
endif
;
; Now update registry
;
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
ifstr(i) $(!STF_GUI_UNATTENDED) == "YES"
Shell $(UtilityInf),AddDefaultNetCardParameters,$(KeyParameters)
endif
;
; If the network address has been deleted then also delete it from
; the registry.
;
ifstr $(OldNetAddress) != ""
ifstr $(NetworkAddress) == ""
DeleteRegValue $(KeyParameters) NetworkAddress
endif
endif
;
; If we're not installing a PCMCIA Card, remove PCMCIA specific settings
;
ifcontains(i) $(Option) in {"OCTK3117","OCTK3118","OCTK3133","OCTK3129","OCTK3136","OCTK3137"}
DeleteRegValue $(KeyParameters) IoBaseAddress
DeleteRegValue $(KeyParameters) IoLength
DeleteRegValue $(KeyParameters) IoBaseAddress_1
DeleteRegValue $(KeyParameters) IoLength_1
DeleteRegValue $(KeyParameters) ModemFunction
DeleteRegValue $(KeyParameters) PCCARDAttributeMemoryAddress
DeleteRegValue $(KeyParameters) PCCARDAttributeMemorySize
DeleteRegValue $(KeyParameters) PCCARDAttributeMemoryOffset
DeleteRegValue $(KeyParameters) InterruptNumber
DeleteRegValue $(KeyParameters) ComPortBase
DeleteRegValue $(KeyParameters) PcmciaCtrlBase
DeleteRegValue $(KeyParameters) Pcmcia
DeleteRegValue $(KeyParameters) WaitStates
DeleteRegValue $(KeyParameters) DataSize
endif
ifcontains(i) $(Option) in {"OCTK3220","OCTK3221"}
DeleteRegValue $(KeyParameters) ComPortBase
DeleteRegValue $(KeyParameters) IoBaseAddress_1
DeleteRegValue $(KeyParameters) IoLength_1
DeleteRegValue $(KeyParameters) ModemFunction
endif
ifcontains(i) $(Option) in {"OCTK3230","OCTK3232"}
ifint $(IOBasePCMCIAControllerValue) != 0
DeleteRegValue $(KeyParameters) IoBaseAddress_1
DeleteRegValue $(KeyParameters) IoLength_1
DeleteRegValue $(KeyParameters) ModemFunction
endif
endif
ifcontains(i) $(Option) not-in {"OCTK3136","OCTK3137"}
DeleteRegValue $(KeyParameters) SlotNumber
endif
CloseRegKey $(KeyParameters)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
Debug-Output "Registry error: Add value list"
goto fatalregistry
endif
;
; Add some keywords to the PCMCIA database in the registry
;
ifcontains(i) $(Option) not-in {"OCTK3117","OCTK3118","OCTK3133","OCTK3129","OCTK3136","OCTK3137"}
set PCMCIADatabaseKeyName = $(!NTN_ServiceBase)"\Pcmcia\DataBase"
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseKeyName) $(MAXIMUM_ALLOWED) PCMCIADatabaseKey
ifstr $(PCMCIADatabaseKey) != $(NULL)
CreateRegKey $(PCMCIADatabaseKey) {"Olicom", 0, 0} "" $(MAXIMUM_ALLOWED) "" PCMCIADatabaseManuKey
ifstr $(PCMCIADatabaseManuKey) == $(NULL)
set PCMCIADatabaseManuKeyName = $(PCMCIADatabaseKeyName)"\Olicom"
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseManuKeyName) $(MAXIMUM_ALLOWED) PCMCIADatabaseManuKey
endif
CreateRegKey $(PCMCIADatabaseManuKey) {"TR16/4", 0, 0} "" $(MAXIMUM_ALLOWED) 0 PCMCIADatabaseManuCardKey
ifstr $(PCMCIADatabaseManuCardKey) == $(NULL)
set PCMCIADatabaseManuCardKeyName = $(PCMCIADatabaseKeyName)"\Olicom\TR16/4"
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseManuCardKeyName) $(MAXIMUM_ALLOWED) PCMCIADatabaseManuCardKey
endif
SetRegValue $(PCMCIADatabaseManuCardKey) {Driver, 0, $(!REG_VT_SZ),"octk16"}
SetRegValue $(PCMCIADatabaseManuCardKey) {DeviceType, 0, $(!REG_VT_SZ),"NET"}
SetRegValue $(PCMCIADatabaseManuCardKey) {AttributeMemorySize, 0, $(!REG_VT_DWORD),4096}
CloseRegKey $(PCMCIADatabaseManuCardKey)
CreateRegKey $(PCMCIADatabaseManuKey) {"TR 16/4 II", 0, 0} "" $(MAXIMUM_ALLOWED) 0 PCMCIADatabaseManuCardKey
ifstr $(PCMCIADatabaseManuCardKey) == $(NULL)
set PCMCIADatabaseManuCardKeyName = $(PCMCIADatabaseKeyName)"\Olicom\TR 16/4 II"
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseManuCardKeyName) $(MAXIMUM_ALLOWED) PCMCIADatabaseManuCardKey
endif
SetRegValue $(PCMCIADatabaseManuCardKey) {Driver, 0, $(!REG_VT_SZ),"octk16"}
SetRegValue $(PCMCIADatabaseManuCardKey) {DeviceType, 0, $(!REG_VT_SZ),"NET"}
SetRegValue $(PCMCIADatabaseManuCardKey) {AttributeMemorySize, 0, $(!REG_VT_DWORD),4096}
CloseRegKey $(PCMCIADatabaseManuCardKey)
CreateRegKey $(PCMCIADatabaseManuKey) {"GoCard Token-Ring 16/4+Modem 14400", 0, 0} "" $(MAXIMUM_ALLOWED) 0 PCMCIADatabaseManuCardKey
ifstr $(PCMCIADatabaseManuCardKey) == $(NULL)
set PCMCIADatabaseManuCardKeyName = $(PCMCIADatabaseKeyName)"\Olicom\GoCard Token-Ring 16/4+Modem 14400"
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseManuCardKeyName) $(MAXIMUM_ALLOWED) PCMCIADatabaseManuCardKey
endif
SetRegValue $(PCMCIADatabaseManuCardKey) {Driver, 0, $(!REG_VT_SZ),"octk16"}
SetRegValue $(PCMCIADatabaseManuCardKey) {DeviceType, 0, $(!REG_VT_SZ),"NET"}
SetRegValue $(PCMCIADatabaseManuCardKey) {AttributeMemorySize, 0, $(!REG_VT_DWORD),4096}
CloseRegKey $(PCMCIADatabaseManuCardKey)
CreateRegKey $(PCMCIADatabaseManuKey) {"GoCard TRN/Modem 336", 0, 0} "" $(MAXIMUM_ALLOWED) 0 PCMCIADatabaseManuCardKey
ifstr $(PCMCIADatabaseManuCardKey) == $(NULL)
set PCMCIADatabaseManuCardKeyName = $(PCMCIADatabaseKeyName)"\Olicom\GoCard TRN/Modem 336"
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseManuCardKeyName) $(MAXIMUM_ALLOWED) PCMCIADatabaseManuCardKey
endif
SetRegValue $(PCMCIADatabaseManuCardKey) {Driver, 0, $(!REG_VT_SZ),"octk16"}
SetRegValue $(PCMCIADatabaseManuCardKey) {DeviceType, 0, $(!REG_VT_SZ),"NET"}
SetRegValue $(PCMCIADatabaseManuCardKey) {AttributeMemorySize, 0, $(!REG_VT_DWORD),4096}
CloseRegKey $(PCMCIADatabaseManuCardKey)
Endif
Endif
EndWait
goto successful
bindingadapter =+
set Error = "Binding: Sorry, not yet implemented."
goto fatal
;-----------------------------------------------
; Remove Adapter Section
;-----------------------------------------------
;
; Remove all adapter information from the registry
;
removeadapter = +
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(subroutineinf) SetupMessage $(!STF_LANGUAGE) STATUS "Remove SW"
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
else
;
; Remove associated Com port if required
;
ifcontains(i) $(Option) in {"OCTK3230","OCTK3232"}
Split-String $(!NTN_RegBase), "\", CardInfo
set AdapterNumber = *($(CardInfo),11)
set ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)$(AdapterNumber)"\Parameters"
OpenRegKey $(!REG_H_LOCAL) "" $(ParamKeyName) $(!REG_KEY_READ) KeyComPortBase
GetRegValue $(KeyComPortBase) "ComPortBase" ComPortBaseInfo
set ComPortBase = *($(ComPortBaseInfo), 3);
CloseRegKey $(KeyComPortBase)
ifstr(i) $(ComPortBase) != 0
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) SerialHandle
DeleteRegTree $(SerialHandle) "SerialOctk16"
CloseRegKey $(SerialHandle)
OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP\SERIALCOMM" $(MAXIMUM_ALLOWED) SerialHandle
DeleteRegValue $(SerialHandle) "SerialOctk16"
CloseRegKey $(SerialHandle)
endif
endif
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $(!NTN_RegBase)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
UpgradeSoftware = +
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set !UG_Filename = $($R0)
install "Install-Update"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
goto fatal
endif
SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)}
SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)}
CloseRegKey $(KeyProduct)
else
goto fatalregistry
endif
goto end
successful = +
goto end
abandon = +
ForListDo $(OEM_ABANDON_OPTIONS)
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $($)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
EndForListDo
Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), FALSE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
warning = +
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(to)
else-ifstr(i) $($R1) == "CANCEL"
goto $(from)
else
goto "end"
endif
nonfatalinfo = +
Set Severity = STATUS
Set CommonStatus = STATUS_USERCANCEL
goto nonfatalmsg
nonfatal = +
Set Severity = NONFATAL
goto nonfatalmsg
nonfatalmsg = +
ifstr(i) $(Error) == ""
Set Severity = NONFATAL
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(from)
else
goto "end"
endif
fatalregistry = +
Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
fatal = +
ifstr(i) $(Error) == ""
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
goto setfailed
ShellCodeError = +
set DlgType = "MessageBox"
set STF_MB_TITLE = "Error: "$(FunctionTitle)
set STF_MB_TEXT = "Shell Code Error"
set STF_MB_TYPE = 1
set STF_MB_ICON = 3
set STF_MB_DEF = 1
ui start "Error Message"
goto setfailed
setfailed = +
set CommonStatus = STATUS_FAILED
ifstr(i) $(OEM_ABANDON_ON) == TRUE
set OEM_ABANDON_ON = FALSE
goto abandon
endif
goto end
end = +
goto term
term = +
Return $(CommonStatus)
[Install-Option]
set STF_VITAL = ""
ifstr(i) $(AddCopy) == "YES"
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
endif
Debug-Output "OEMSETUP.INF: [Install-Option] DoCopy = "$(DoCopy)
ifstr(i) $(DoCopy) == "YES"
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
endif
Exit
[Install-Update]
set STF_VITAL = ""
set STF_OVERWRITE = "VERIFYSOURCEOLDER"
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH)
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
exit
[Install-Dll]
set STF_VITAL = ""
ifstr(i) $(AddCopy) == "YES"
AddSectionFilesToCopyList Files-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH)
endif
ifstr(i) $(DoCopy) == "YES"
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
else
; get minimum needed files for configuration
LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\OCTK16.DLL $(!STF_WINDOWSSYSPATH)\OCTK16.DLL
LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\OCTK16.HLP $(!STF_WINDOWSSYSPATH)\OCTK16.HLP
endif
exit
[Source Media Descriptions]
1 = "Olicom Driver Disk"
[ProductType]
STF_PRODUCT = Winnt
STF_PLATFORM = I386
[Files-Inf]
1, oemsetnt.inf, SIZE=999, RENAME=$(!UG_Filename)
[Files-OcTk3117]
1, octk16.sys, SIZE=999
[Files-OcTk3118]
1, octk16.sys, SIZE=999
[Files-OcTk3133]
1, octk16.sys, SIZE=999
[Files-OcTk3136]
1, octk16.sys, SIZE=999
[Files-OcTk3137]
1, octk16.sys, SIZE=999
[Files-OcTk3129]
1, octk16.sys, SIZE=999
[Files-OcTk3220]
1, octk16.sys, SIZE=999
[Files-OcTk3221]
1, octk16.sys, SIZE=999
[Files-OCTK3230]
1, octk16.sys, SIZE=999
1, serial.sys, SIZE=999
1, ocmdm144.inf, SIZE=999, DESTINATION=$(!STF_WINDOWSPATH)\INF
1, ocmdm336.inf, SIZE=999, DESTINATION=$(!STF_WINDOWSPATH)\INF
[Files-OCTK3232]
1, octk16.sys, SIZE=999
1, serial.sys, SIZE=999
1, ocmdm144.inf, SIZE=999, DESTINATION=$(!STF_WINDOWSPATH)\INF
1, ocmdm336.inf, SIZE=999, DESTINATION=$(!STF_WINDOWSPATH)\INF
[Files-Dll]
1, octk16.dll, SIZE=999
1, octk16.hlp, SIZE=999
[Files-dummy]
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.