1. em110_d1.zip Driver
2. NW-STND.TXT File Contents

NW-STND.TXT Driver File Contents (em110_d1.zip)

							Apr-21-97
  
NETWARE DRIVER INSTALLATION PROCEDUREs

  Contents of this file:
  
  A) Installation and configuration for Netware 3.1x.
	-using manual installation
  B) Installation and configuration for Netware 4.x.
	-using INETCFG.NLM
  C) Manual installation.

  ================================================================
  A) Installation/Configuration of Driver for Netware 3.x
  ================================================================
  INSTALLATION
  ------------

  1) Make sure is that system is clean.
     - Remove the adapters.
     - Remove all the load and bind commands related to EMPCI
       from the "SYS:SYSTEM\AUTOEXEC.NCF" 

  2) Copy all the files from the installation diskette
     A:\Nwserver\ directory to the C:\NWSERVER directory.

  3) Edit AUTOEXEC.NCF file manually, place proper load and bind
     commands.(See sample load and bind commands below.)

       # load commands
       LOAD C:EMPCI NAME=P1 FRAME=ETHERNET_802.2 INDEX=1
       LOAD C:EMPCI NAME=P2 FRAME=ETHERNET_802.2 INDEX=2

       # bind commands

       BIND IPX P1 NET=101
       BIND IPX P2 NET=102

       # load command for DMI agent 
       LOAD CDTDMI 

       #CDTDMI.MIB can be found on the Server driver disk in the 
       #NWSERVER directory

  3) Down the server and reboot for the configuration to take effect.

  ================================================================
  B) Installation/Configuration of Driver for Netware 4.x
  ================================================================

  Using INETCFG utility
  ---------------------

  INETCFG.NLM is the recommended utility to properly install
  and configure the Netware driver.  

  0) Make sure to delete previously installed adapters.
     -remove all load and bind commands relating to EMPCI driver
      from the Autoexec.ncf as well as the "SYS:ETC\FAILOVER.NCF",
      if this file exists.

  1) At the console prompt type "LOAD INETCFG" and press enter.

  2) Answer "YES" when asked to transfer all commands from the 
     Autoexec.ncf.

  3) From the main menu, select "BOARDS" and press Enter. You will be
     presented with a list of installed adapters. Delete all previous 
     instances of the EMPCI driver, if any exist, making sure to remove 
     the bindings when prompted.

  4) A)Press "INS" to add a new driver. You will be presented
     with the list of available LAN drivers to choose from. 

     B)Do not select an adapter from the list at this time.

     C)Press "INS" again and install the driver from the Netware
     Driver Diskette. Be sure to specify the correct path to the
     new EMPCI.LAN (a:\nwserver\empci.lan for example)
    
     D)You will need to select the new EMCPI from the updated list.

  6) Provide a name for the newly added adapter.

  7) Specify the INDEX number on next field (1 is default for
     first board and 2 should be set for the next board, etc.)

  8) Specify HALF or FULL Duplex mode 

  9) Press "ESC" and save the configuration. 

 10) From the INETCFG main menu, select PROTOCOLS. Select the appropriate
     protocols for your network.

 11) Use the "ESC" key to exit, saving your protocol configuration.

 12)  From the INETCFG main menu, select BINDINGS. Highlight the protocol 
     you wish to bind and press INSERT. Continue until all bindings are 
     complete. Repeat the process for any additional adapters in the system.

 13) Use the "ESC" to exit from the BINDINGS area, saving your 
     configuration as you exit. Use the "ESC" key again to exit the 
     INETCFG utility.

 14) At server console type: "restart system" to down the server and restart
     using the new configuration. 

** For SNMP support **
    
1. Log into the server via a client and copy CDTDMI.NLM and FAILMIB.NLM 
   (located in the NWSERVER directory on your Adaptec driver disk) into 
   the SYS:SYSTEM directory on the server.  
2. Put the following two lines at the end of the AUTOEXEC.NCF file:
    "LOAD CDTDMI"
    "LOAD FAILMIB"


  ==============================
  C) Manual Installation 
  ==============================
  
  This is the manual installation method without using
  the INETCFG utility under NW 4.x.


  INSTALLATION
  ------------

  0) Make sure is that system is clean.
     - Remove the adapters.
     - Remove all the load and bind commands related to EMPCI
       from the "SYS:SYSTEM\AUTOEXEC.NCF" as well as
       "SYS:ETC\FAILOVER.NCF" line in "Autoexec.ncf file if 
       it exists.

  1) Copy all the files from the installation diskette
     A:\Nwserver\ directory to C:\NWSERVER directory.

  2) Edit AUTOEXEC.NCF file manually, place proper load and bind
     commands.(See sample load and bind commands below.)

       # to load TCP/IP protocol, not needed if TCP/IP is not used.
       LOAD TCPIP

       # load command for PRIMARY  (B_INDEX indicates Backup INDEX Number)
       LOAD C:EMPCI NAME=PRIMARY_E82 FRAME=ETHERNET_802.2 INDEX=1 B_INDEX=2

       # load command for BACKUP, P_INDEX indicates Primary INDEX Number.
       LOAD C:EMPCI NAME=BACKUP_E82 FRAME=ETHERNET_802.2 INDEX=2 P_INDEX=1

       # bind command for PRIMARY, there should not be any bind command
       # for BACKUP.
       BIND IPX PRIMARY_E82 NET=101

       # load command for DMI agent (except FAILOVER)
       LOAD CDTDMI

  3) Down the server and reboot for the configuration to take effect.