1. 9508321a.exe Driver
2. HISTORY.TXT File Contents

HISTORY.TXT Driver File Contents (9508321a.exe)

*****************************************************
Gateway Version History:

Revision 2.0  06/23/2000  PHATLE
FILE: 9508321.ZIP
Update to latest BIOS: Version 13.0 Build 125
Update to latest FIRMWARE: Version 1.13
Update to latest FRUSDR: Version 4.2.3
 
Revision 1.1  02/21/2000  SARRAJOH
FILE: 9507246.ZIP
Initial revision
*****************************************************

Revision History:

06/23/2000

	BIOS: Version 13.0 Build 125
	FILE: 9508314.ZIP

1.  Support for 1GHz Pentium III Processors.  NOTE: All .18u Pentium 
    III B0 stepping QSpec parts are clock locked.
2.  Fixed issue where 640K Base Memory test was being overwritten on 
    POST Diagnostic screen.
3.  Fixed issue with speed mismatched processors not being disabled.  
    Now, the slower of the 2 processors will be disabled on reboot.  
    This has a side effect of not allowing and unlocked processor 
    that was set a different speed having a locked processor added to 
    the configuration.
4.  Fixed issue where CMOS was not being properly restored when 
    corrupted.
5.  Fixed issue where 133MHz FSB processors were being allowed to 
    operate in the system.  NOTE:  This feature does not work with 
    Q spec part but will work with S spec and production parts.
6.  Added feature to prevent boards lower that FAB7 from booting
    processors faster than 850MHz.
7.  Upgraded PXE 0.99c option ROM to PXE 2.x Build 78.
8.  Added updated Japanese Setup translations.
9.  Fixed issue with mixing 681 A2 and 683 B0 processors of the same 
    speed displaying a processor speed mismatch error erronously.
10. Removed corrupted Japanese strings from Setup. They will appear 
    in English until updated translations are provided.
11. Fixed WOR for COM2 under ACPI OS.
12. Fixed INT15h handler for microcode updates. Now multiple 
    processors can be updated.
13. Fixed virus protection and Master Boot Record write protect
    feature. Now, these will only protect the hard drive when booted 
    from a floppy.


----------
06/23/2000

	FIRMWARE: Version 1.13
	FILE: 9508316.ZIP

1.  Previous versions of the firmware did not report the status
    of the SUSSTAT1 signal in the response to the Get ACPI 
    Configuration command. BMC 1.13 now reports a "1" for SUSSTAT1 
    when the signal is active, indicating that the server is in S1 
    sleep.
2.  When Windows 2000 (or any ACPI OS) put the server into Standby 
    mode (ACPI S1 sleep), the BMC did not automatically disable the 
    watchdog timer. If server management software was using the timer 
    when the system went into standby, the BMC would then reset or 
    power cycle the server when the timer expired. To avoid this, the 
    BMC now turns off the timer when the server enters S1 sleep.
3.  Modified Get Device ID command, when in firmware transfer mode, 
    to return an additional 6th byte for capabilities. The sixth byte 
    indicates that no IPMI capabilities for accessing the SEL, SDR, 
    FRU, or ICMB exist during firmware update.
4.  When a Chassis Control power down or power cycle command was
    sent to the BMC, the system would power down but would not power 
    up again until AC power was removed and re-applied. This has been 
    fixed in BMC 1.11.
5.  The server would not recover from a short term AC power
    loss in which 5 volt standby power to the BMC was not lost. BMC 
    1.11 correctly detects this and power cycles the server.
6.  The server would not power up when certain non-ATX compliant
    power supplies were installed. Support for such supplies has been
    improved in BMC 1.11, however operation with non-ATX compliant 
    power supplies is not guaranteed.
7.  Added the following new sensors;
	sensor 0x29 Power Unit		: power cycle, AC lost
	sensor 0x2A Redundancy Lost	: regained, lost
	sensor 0x2B Power Supply #1	: presense & failure detected
	sensor 0x2C Power Supply #2	: presense & failure detected
	sensor 0x2D PDB Temperature	: threshold
    If a power supply failure is detected the power fault LED signal 
    is asserted. Similarly, if a power supply fan fails the cooling 
    fault LED signal is asserted.
8.  Updated the I2C communications library to the latest version. This
    reduces the chances of communication failure under high I2C
    traffic loads.
9.  Added a synchronization between power state changes and the I2C
    sensor tasks, and I2c traffic. This should also improve I2C
    communications reliability.


----------
06/23/2000

	FRUSDR: Version 4.2.3
	FILE: 9508319.ZIP

1.  Added SDRs to support different processor voltages and speeds.


----------
04/12/2000

	BIOS: Version 12.1 Build 115
	FILE: 9507067.ZIP

    1.  Added support for 683 B0 Pentiumr(r) III processors
    2.  Added support for Pentiumr III 850 MHz processors 
    3.  Fixes will be added to support the Microsoft WHQL HCT 9.5 test 
        suite
    4.  Help text will be added to the BIOS setup utility to help 
        identify EMP setup dependencies.
    5.  Fix: to support ISC issue if BIOS is not set to English
    6.  Fix: to support dual SRCU21 RAID cards
    7.  Fix: SBE SEL record data
    8.  Fix: BIOS ID not in English
    9.  Fix: Non-ECC memory identified as ECC at POST
   10.  Fix: Processors model mis-match error 8188
   11.  Added help text to distinguish which processors are supported on 
        different boards
   12.  Move Floppy option from multi-boot to removable devices in BIOS 
        Setup utility
   13.  Removed unused debug components and outs to Port 80h
   14.  Fix: issue: if a critical POST error occurs and Quiet Boot is 
        enabled, the system hangs at logo screen
   15.  Fix: POST Hang after exiting BIOS setup and discarding changes 
        twice

----------
03/24/2000

	Initial Release

	BIOS: Version 11.2 Build 105
	FILE: 9506592.ZIP

	FIRMWARE: Version 1.08
	FILE: 9506915.ZIP

	FRUSDR: Version 4.01.2
	FILE: 9507088.ZIP