STDAT4.TXT 08-04-99 ______________________________________________________________________ _ _ _ / / (_) _\ \ \ Seagate DAT Tape Driver v1.08 (_)_/_/ for Windows NT 4.0 Intel Platform - STDAT4.SYS ______________________________________________________________________ Copyright (c) 1998-1999 Seagate Technology, Inc. All rights reserved ====================================================================== This document gives installation instructions for a software driver used to run Seagate SCSI DAT tape drives on Microsoft Windows NT 4.0 Intel platforms. This driver works with Intel 386, 486, Pentium computers. It is required if your drive is labeled "Seagate", and has an "STDxxxxx" part number. This STDAT4.SYS driver differs from the 4MMDAT.SYS driver, supplied with Windows NT 4.0 as follows: * STDAT4.SYS recognizes Seagate model STDxxxxx tape drives. These models return "SEAGATE DAT" data in response to a SCSI Inquiry command. * Timeouts are increased to 15 minutes for Read, Write, Write Filemarks, Space, Locate, Erase(short), and Rewind operations. Longer timeouts are only needed when a tape drive performs an error recovery procdure because of a difficulty reading a tape. Old timeout values ranged from 6 to 8 minutes. If you did not receive this file on a diskette or CD-ROM, you must create an installation diskette first. See the section below titled "Installation Overview" for instructions. ====================================================================== SCSI DAT Device Driver Installation ----------------------------------- Install the STDAT4.SYS device driver using this procedure: For Windows NT 4.0: 1. If you are installing from CD-ROM, locate the STDAT4 directory containing the file OEMSETUP.INF. Remember the directory's <CD-drive-letter>:\<path>. Otherwise, if you are installing from diskette, insert the diskette, labeled as follows, into the floppy drive: "Seagate DAT Tape Driver v1.08 for Windows NT 4.0 Intel Platform" 2. Start up the tape device driver installation program by selecting 'Start' -> 'Settings' -> 'Control Panel', then double clicking the 'Tape Devices' icon. 3. Select the 'Drivers' tab. 4. In the 'Installed Driver' box, click the 'Add...' button. 5. In the 'Install Driver' box, click the 'Have Disk...' button. 6. You will see a 'Install From Disk' box message -- 'Copy from manufacturer's files from: <source_path>'. If you are installing from CD-ROM, set the <source_path> to the <CD-drive-letter>:\<path> containing the file OEMSETUP.INF remembered in step 1, then click the 'OK' button. Otherwise if you are installing from a floppy diskette, set the <source_path> to 'A:\' (or your floppy drive letter), then click the 'OK' button. 7. In the 'Install Driver' box's 'Tape Devices' list, you will see -- 'Seagate DAT (stdat4.sys)'. Select the device model number which is the closest match to the label on your tape drive then click the 'Install' button. Note. This choice is not critical. 8. If you see a 'Windows NT Setup' box with the message -- 'The driver(s) for this Tape Device are already on the system. Do you want to use the currently installed driver(s) or install new one(s).', click the 'New' button. 9. You may see a 'Windows NT Setup' box with the message -- 'Please enter the full path to the Seagate Tape device files. Then choose Continue. <source_path>'. If you are installing from CD-ROM, set the <source_path> to the directory remembered in step 1. To this appended either \I386 for Intel computers, or \ALPHA for DEC Alpha computers. That is, set the <source_path> to <CD-drive-letter>:\<path>\I386 then click the 'Continue' button. Otherwise if you are installing from a floppy diskette, set the <source_path> to 'A:\I386' then click the 'Continue' button. 10. In the 'System Settings Change' box message, you will see -- 'You must restart your computer before the new settings will take effect. Do you want to restart your computer now?'. Remove the driver installation diskette, then click 'Yes' to shut down and restart the system. The Seagate DAT Tape Driver is now installed and ready to use. You may want to use the 'Administrative Tools' -> 'Backup' applet to verify correct tape drive operation. ====================================================================== Additional Contents ------------------- * Supported Tape Drive Models * Installation Overview * Creating an Installation Diskette from the file STDAT4.EXE * DAT Drive Hardware Configuration * Removing the Tape Driver from the System Configuration * Uninstalling Tape Driver Files * Important Notes -- Tape Drive Firmware Version Determination -- Examining Tape Device Driver Start Status -- Examining the Version of 'stdat3.sys' -- Events 9 and/or 11 in Event Viewer with a SCSI tape and SCSI hard disk ====================================================================== Supported Tape Drive Models --------------------------- The list below identifies Seagate and Conner DAT tape drive models supported by the STDAT4.SYS driver. I386\STDAT4.SYS -- Seagate DAT Tape Driver v1.08 for Windows NT 4.0 Intel Platform File date: 07-29-99 File size: 12,032 Tape Drive Models ----------------- STD12000N, STD22000N, STD62000N STD14000N, STD24000N, STD64000N STD18000N, STD28000N, STD68000N, STD28000N-RFT, STD68000N-RFT STD124000N, STD224000N, STD624000N, STD224000N-RFT, STD624000N-RFT STD1401LW, STD2401LW, STD6401LW 4586NP, 4586XP STL496000N, STL696000N STDL42401LW, STDL62401LW Note. Seagate acquired Conner in February 1996. ====================================================================== Installation Overview --------------------- Use this general procedure to install a tape drive in the computer: * Create a driver installation diskette from the file STDAT4.EXE. * Configure the tape drive's switches and install the tape drive in the computer. * Install the tape driver from the Seagate tape driver installation diskette. * Reboot the system and verify correct operation. ====================================================================== Creating an Installation Diskette from the File STDAT4.EXE ---------------------------------------------------------- This procedure creates a tape driver installation diskette. It assumes you have downloaded the file STDAT4.EXE to your system. You also need formatted, empty diskette. STDAT4.EXE is a self- extracting 16-bit WinZip program. Note. If you already have a driver installation diskette labeled "Seagate SCSI Travan Tape Driver v1.08 for Windows NT 4.0 Intel Platform", skip this procedure. 1. Label the diskette: "Seagate SCSI Travan Tape Driver v1.08 for Windows NT 4.0 Intel Platform". 2. On a Windows 3.1x, 9x, or NT, run STDAT4.EXE, open Windows Explorer or Program Manager as appropriate. 3. Locate the down-load directory containing STDAT4.EXE. 4. Double click STDAT4.EXE to start the self-extractor. 5. You will see a dialogue box titled WinZip Self-Extractor [STDAT4.EXE]. 6. In the Unzip To Folder field, set your floppy drive letter (for example A:). 7. Click the Unzip button. 8. You will see "3 file(s) unzipped successfully", then click OK. 9. Click Close This extracts files and creates the driver installation diskette with the following files (where A: is the floppy drive letter): A:\STDAT4.TXT This document A:\OEMSETUP.INF Setup information A:\I386\STDAT4.SYS Seagate DAT tape driver for Intel 10. You may want to write protect the diskette. This completes the installation diskette creation procedure. Return to "SCSI DAT Device Driver Installation" above. ====================================================================== DAT Drive Hardware Configuration -------------------------------- Please pay attention to these hardware configuration recommendations for Seagate and Conner DAT tape drives: * Shut down the system and turn power off before installing or configuring hardware. * Select a tape drive SCSI ID that does not conflict with the other devices connected to the SCSI cable. Usually SCSI ID 4, 5, or 6 are good choices. Normally, hard discs are configured in ascending order starting with SCSI ID 0 and the SCSI host adapter is set to the SCSI ID 7 or 15. * Your SCSI host adapter should be configured to 'Enable Disconnect' for all SCSI device IDs. It is especially critical that the SCSI adapter be configured to 'Enable Disconnect' for the tape drive's device ID. If not, then accesses to the SCSI hard disc can timeout because they cannot gain access to the SCSI bus during long duration tape commands such as Rewind or Seek to End-of-Data. If you have an Adaptec SCSI Host Adapter, you may be able to set the 'Enable Disconnect' configuration by entering <Ctrl><A> to enter the Adaptec BIOS during boot. Consult your SCSI host adapter manual. * The SCSI cable must be correctly electrically terminated at both ends and only at the ends. Forms of cable termination vary. Termination may be built into the cable end or ends. Termination may be in the form of a terminator plug which is either plugged into the end of the cable or plugged into a pass through connector, if present, on the SCSI device attached to the end of a cable. Many SCSI devices provide termination as a selectable function which can be enabled, via jumper or switch, when the device is connected to the end of the cable. SCSI devices, in the middle of the cable daisy chain, should have both terminators and termination power disabled. Most Seagate DAT drives may be used to terminate the end of a cable by setting the jumpers for 'ACT. TERM' (active termination) and 'TERM PWR' (termination power). To disable the termination function, park the jumpers by letting them hang on a single pin. Consult the hardware documentation for your SCSI adapter and other SCSI devices for more configuration and termination information. ====================================================================== Removing the Tape Driver from the System Configuration ------------------------------------------------------ This procedure removes the STDAT4.SYS driver from the system configuration, but does not delete driver files. 1. From the desktop, click 'Start' -> 'Settings' -> 'Control Panel', then double clicking the 'Tape Devices' icon. 2. In the 'Tape Devices' box, select the 'Drivers' tab. 3. In the 'Installed tape drivers are listed below' list, highlight the entry that contains 'Seagate DAT (stdat4.sys)', then click the 'Remove' button. 4. You will see a 'Remove Driver' box message -- 'Are you sure you want to remove this driver?' then click the 'Yes' button. 5. In the 'Tape Devices' box, click 'OK'. 6. Shutdown and restart the system. The SCSI DAT tape driver is now removed from the system configuration. ====================================================================== Uninstalling Tape Driver Files ------------------------------ To completely uninstall the tape driver including deleting the driver files follow these steps: 1. Follow the instructions in section "Removing the Tape Driver from the System Configuration" above. 2. Using Windows NT Explorer or an MS-DOS command prompt, delete the tape driver file C:\WINNT\SYSTEM32\DRIVERS\STDAT4.SYS. Note. C:\WINNT\ is the directory in which Windows NT is installed. It may be different on your system. 3. In the directory C:\WINNT\INF\ identify, for removal, any OEM*.INF and corresponding OEM*.PNF which were created during the STDAT4.SYS driver installation. Where '*' is an integer. For example OEM0.INF, OEM1.INF, etc (and corresponding OEM0.PNF, OEM1.PNF, etc). OEM*.INF files contain ASCII text instructions used by Windows NT Setup to add and remove drivers. For each OEM*.INF, setup creates a corresponding OEM*.PNF file. CAUTION: There may be OEM*.INF (and corresponding OEM*.PNF) files installed for other (non-tape) device drivers. Do NOT delete these files. To identify the OEM*.INF and corresponding OEM*.PNF files associated with STDAT4.SYS from an MS-DOS command prompt, use these commands: cd C:\WINNT\INF findstr /m /i stdat4.sys oem*.inf Findstr will display a list of zero or more files. For example: oem0.inf For this example, delete both OEM0.INF and OEM0.PNF. An alternate method for locating OEM*.INF (and corresponding OEM*.PNF) files associated with STDAT4.SYS is to examine the final line of each OEM*.INF file with an editor such as NOTEPAD.EXE. If the final line of the .INF file contains the driver file name "stdat4.sys", delete the .INF file and its corresponding .PNF file. For example, if the final line of OEM0.INF is similar to: stdat4 = 1,stdat4.sys , SIZE=21536 then delete both OEM0.INF and OEM0.PNF. The SCSI DAT Tape Driver files are now completely removed. ====================================================================== Important Notes --------------- Tape Drive Firmware Version Determination You can find the tape driver firmware revision using the 'Backup' applet. 1. Start the 'Backup' applet using 'Start' -> 'Administrative Tools' -> 'Backup'. 2. From the menu bar, select 'Operations' -> 'Hardware Setup...' 3. This opens the 'Hardware Setup' which looks something like ... 'Tape Drive Scsi 0, Bus 0, ID 4, Lun 0, Seagate STT8000N 3.12' The last field in the Tape Drive description (3.12 in this example) is the firmware revision. Examining Tape Device Driver Start Status If you wish to examine whether certain tape related device drivers are started, use the 'Devices' window. To start the 'Devices' window, click the following: Start -> Settings -> Control Panel -> Devices. The following shows how the 'Device' entries of interest are set when drivers are operating correctly: Device Status Startup ------ ------- ------- <scsiadapter> Started Boot stdat4 Started System Examining the Version of 'stdat4.sys' 1. Start 'Windows NT Explorer'. 2. Highlight the file C:\Winnt\system32\drivers\stdat4.sys. 3. From the menu bar, select File -> Properties. 4. In the 'stdat4.sys Properties' box, select the 'Version' tab. You should see 'File version: 4.00.Seagate.1.08'. Events 9 and/or 11 in Event Viewer with a SCSI tape and SCSI hard disc If you are experiencing tape device errors during backup or restore operations and seeing these events in Administrative Tools -> Event Viewer 'Event ID: 9 Description: The device, \Device\ScsiPort0, did not respond within the timeout period.', and/or 'Event ID: 11 Description: The driver detected a controller error on \Device\ScsiPort0.', the cause may be that the SCSI adapter is not configured to 'Disconnect' the tape drive from the SCSI bus. When the SCSI bus is not disconnected during a long duration tape command, such as Rewind, then disc access commands time out waiting to get access to the bus. If you have an Adaptec 1542C controller, 'Enable Disconnect' should be set to 'Yes' (the recommended default for all SCSI devices) at least for the tape drive. Typically this configuration can be set by entering the Adaptec BIOS Setup using <Ctrl><A> during the boot process. -= End of File: STDAT4.TXT =-Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.