---------------------------------------------------------------------------- Installing the NetWare 3/4 ODI Server Driver on NetWare 4 Servers ---------------------------------------------------------------------------- The \NOVELL\SRVODI subdirectory contains the following files: README.TXT - This file. EWRK3.LAN - Novell NetWare 3/4 ODI Server Driver for the DEC EtherWORKS 3 Ethernet Controller (v2.11). EWRK3.LDI - Driver installation file used by NetWare 4 installation utility (INSTALL.NLM) to install and configure the NetWare 3/4 ODI Server Driver in that environment. This is the same file as A:\EWRK3.LDI. MSM.NLM - Novell supplied MSM module (V2.50) ETHERTSM.NLM - Novell supplied TSM module (V2.50) The \NOVELL\SRVODI subdirectory contains the following subdirectory: \3_X - Files for installing and configuring the NetWare 3/4 ODI Server Driver in NetWare 3 servers. Product Requirements: Oper. Sys. - Novell NetWare 3.11, 3.12, 4.0, 4.01, 4.02 ***TRADEMARKS*** DEC, Digital, DECpc, and AXP are registered trademarks of Digital Equipment Corporation. Novell, NetWare, and LAN WorkPlace are registered trademarks and NetWare Loadable Module and NLM are trademarks of Novell, Incorporated. Section 1 INSTALLING THE NETWARE 3/4 ODI SERVER DRIVER ------------------------------------------------------------ You can install and use the NetWare 3/4 ODI server driver on NetWare 3 and NetWare 4 servers. The installation procedures are different for each server. To install the NetWare 3/4 ODI server driver on a NetWare 3 file server, follow the instructions in the README.TXT file located in the \3_X directory. To install the NetWare 3/4 ODI server driver on a NetWare 4 file server, perform the following steps: I. Verify that the network interface card (NIC) is properly configured and installed. Refer to "DEC EtherWORKS 3 Owners Manual" for instructions. II. Perform the following steps to install the NetWare 3/4 ODI server driver to the server NetWare partition and to configure and load the driver: A. Reload the INSTALL utility. 1. From the System Console, load INSTALL: :LOAD INSTALL 2. Select "Maintenance/Selective Install" then "LAN Driver Options" under "Installation Options." 3. Hit the Insert <Ins> key to select the "Load a LAN driver not listed" option. Note: 4.01 installs require you to Press F3 and enter the path: "A:\NOVELL\SRVODI" 4. Place the Driver Distribution Diskette into the server floppy drive then press RETURN to scan for NetWare 3/4 ODI server drivers. 5. When "DEC EtherWORKS 3 Novell NetWare Server Driver" appears, press RETURN and follow the instructions to install the driver files. B. From the "Driver EWRK3 parameters" option screen, configure the I/O port address, node address, and frame types. 1. Enter the port address where the DEC EtherWORKS 3 controller was configured via the NICSETUP utility. 2. Enter an optional node address override in canonical-format. If you enter a node address override, that address is added to the driver configuration table and used as a source address on all transmitted frames for that controller. 3. Edit the frame type by pressing the ENTER key when "ETHERNET 802.2" is highlighted. Use the ENTER and F3 keys to load either one or all of the supported Ethernet frame types. If a frame type is not specified, the default frame type, ETHERNET_802.2, is used. 4. Press the F10 key to load the driver. If the driver does not load, use the Alt-Esc key sequence to switch to the System Console and view the driver load error message. 5. If the driver loaded successfully, the INSTALL utility asks whether IPX should be bound to the driver and prompts for a proper external IPX address. Follow the utility instructions to continue, then return to the "Installation Options" menu. 6. To save the configuration information, select "NCF Files Options" then "Create AUTOEXEC.NCF file" to add the driver LOAD and BIND statements to the AUTOEXEC.NCF file. The next time the server is restarted the driver loads and binds to IPX automatically. 7. Exit the INSTALL utility, DOWN the server, and return to the DOS prompt. III. Follow the instructions in the "EtherWORKS 3 Owners Manual" for connecting the controller to the ethernet network. IV. Restart the server with the NetWare 3/4 ODI server driver. Enter the following command at the DOS prompt: SERVER The changes made to the AUTOEXEC.NCF file, in the steps above, will now take effect.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.