PRO120 100/10 Mbps PCI Bus Fast Ethernet Adapters
SCO-UNIX LLI driver Installation Guide
=================================================
A. Introduction
===============
This is a SCO-UNIX LLI driver for the PRO120 PCI Fast Ethernet Adapter whose
released version is 3.2.4. It is installed by "custom" and configured by using
"netconfig" command.
The LLI driver requires the following hardware and software:
- The PCI Fast Ethernet Adapters.
- SCO UNIX ODT 2.0 (rev 3.2.4) or higher version and SCO OpenServer 5.0.
B. SCO UNIX ODT 2.0 Driver Installation Procedures
==================================================
1. Prepare a formatted diskette on any DOS machine. For example, type:
C:>format a:
2. Now boot the SCO-UNIX and enter the Maintenance mode.
Please follow the following steps to uncompressed the package file:
# mkdir /llidrv
# cd /llidrv (and inserts the package floppy in the proper drive, i.e.
drive 'A')
# doscp a:/sco-unix/llidrv/cnetdrv.206 etftar
3. Then replaces with the prepared formatted diskette done in step 1.
# dd if=etftar of=/dev/rfd0135ds18
(Note: Use another device file name if you use a different floppy drive.)
4. Now the package installation diskette is ready for installing.
5. The following sections describe the configuration of the driver. It is
suggested that you should perform these instructions in the singler-user
environment (maintenance mode).
6. Run "custom" command and select the "Install" option when the "Products
Currently Installed" screen is shown.
7. Then select the "A New Product" option after the "Install" screen is shown,
and then choose the "Entire Product" option under the "Select a product"
menu.
8. When the "Insert: Distribution Floppy Volume 1" screen is shown, then enter
directly at the "continue" prompt.
9. When "Insert: PRO120 100/10 Mbps PCI Bus Fast Ethernet Adapter LLI Driver
Floppy Volume 1" screen is shown, please enter the "continue" key to keep
going the install process.
10. When the driver has been installed on the system, please choose the " Quit"
option to exit the "custom" command and continue to run the "netconfig"
command to add the new driver to the network drivers base.
11. After run "netconfig" command, the following screen will be shown as below:
Currently configured chains:
1. sco_tcp->lo0
sco_tcp SCO TCP/IP fot UNIX
lo0 SCO TCP/IP Loopback driver
Available options:
1) Add a chain
2) Remove a chain
3) Reconfigure an element in a chain
4) Quit
Select option:
12. Please follow the indications below to finish the driver installation:
a. Select option 1 "Add a chain"
b. Select top level of chain to Add or q to quit:
please choose the option "1. sco_tcp SCO TCP/IP for UNIX"
c. Select next level of chain to Add or q to quit:
please "PRO120 10/100TX PCI Adapter, board 0"
d. Add chain sco_tcp->etf0 (y/n):
please type 'y' to confirm the choice.
e. Enter the internet Address of this interface: n.n.n.n
f. Enter the netmask for this interface (default 255.255.255.0):
g. Does the interface use a broadcast address of all 1's (y/n)
(default: y)
h. Enter the boardcast address for this interface
(default: n.n.n.n):
i. Are these values correct ? (y/n):
please type 'y'to confirm the choice.
j. Pseudo ttys are currently configured, do you want to:
1) Add Pseudo ttys
2) Remove Pseudo ttys
select an option or enter q to quit [q]:
please type 'q' to exit the installation.
k. Available options:
1) Add a chain
2) Remove a chain
3) Reconfigure an element in a chain
4) Quit
Select option:
please type 'q' to leave the configuration.
l. Do you want to relink to kernel now?
please type 'y' to relink the kernel.
m. Do you want this kernel to boot by default? (y/n)
please type 'y' to use the new kernel as the default boot kernel.
n. Do you want the kernel environment rebuilt? (y/n)
please type 'y' to set up the new kernel environment.
o. Reboot system:
please type "shutdown -g0 -y" or "reboot" to activate the new added
driver under the new UNIX kernel.
C. SCO OpenServer 5.0 Driver Installation Procedures
====================================================
1. Run "custom" command on UNIX system prompt and select the "Install New..."
option under "Software" item. It will prompt you "Installing: PRO120 100/10
Mbps PCI Bus Fast Ethernet Adapter LLI Driver(version 2.0.3)" and then
choose the "FULL" option to install this package.
2. After run the "custom" command and the new package is installed, you should
continue to run the "netconfig" command to add the driver into your system
following the procedures below.
3. Run "netconfig" to add the desired LAN adapter. The steps for adding the
new LAN adapter are listed below:
a. When the "Network Configuration Manager" is shown, please select "Add
new LAN adapter" option under "Hardware" main item.
b. When the screen "Add new LAN Adapter" is shown, then select the option
"Configure hardware not listed above... ]".
c. After "Select network adapter to be added:" is shown, please select the
"PRO120 100/10 Mbps PCI Bus Fast Ethernet Adapter LLI Driver" item to
add the driver into the system.
d. When the driver is selected correctly, the "Add protocol" will be shown,
then select the item "- SCO TCP/IP" as the default protocol stack.
e. After finished the "TCP/IP" protocol choice, the success message will be
shown as following:
"The following products were successfully configured into the system:
SCO TCP/IP
PRO120 100/10 Mbps PCI Bus Fast Ethernet Adapter LLI Driver"
f. When the adapter has been configured, select 'q' from the netconfig
menu, and relink the kernel at the prompt.
4. When the system has been rebooted, you should see the following message
among the other configuration messages:
%etf0 0xE400-0xE480 11 12 speed=100Mbps id=[xx-xx-xx-xx-xx-xx]
With the appropriate I/O addresses, IRQ, PCI Device Number, Line Speed, and
the six octets of the adapter IEEE MAC address.
5. Setup driver line speed parameter.
- Make sure the driver is installed and booted up.
- Change the directory to /etc/conf/pack.d/etf0
- Modify the value of "SpeedMode" which is located in "space.c". If only
one card is installed, please change the value which is included in the
statement of "#ifdef ETF_CNTLS". If two cards are installed, please
change the values which are included in the statements of
"#ifdef ETF_CNTLS" and "#ifdef ETF1_CNTLS". If more than two cards are
installed, please follow the above stated rule to change the line speed
value.
- SpeedMode[] : Default is "NWAY".
NWAY : Start NWAY function to perform media speed detection during
driver initialization.
TX10 : Line speed is set to 10Mbps.
TX10FD : Line speed is set to 10Mbps/Full duplex mode.
TX100 : Line speed is set to 100Mbps.
TX100FD : Line speed is set to 100Mbps/Full duplex mode.
6. If you encounter any problems during installation, (i.e., an error message
appears on screen) call your dealer for assistance.
Notes: a. This driver supports up to maximum 4 boards.
b. Device name is etf0, etf1, etf2, etf3.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.