1. mx.exe Driver
2. README.TXT File Contents

README.TXT Driver File Contents (mx.exe)

Remote Boot to Windows NT Server

Install the NT RPL Server
---------------------------
1. Install the Remoteboot Service on the NT Server.

1.1 Choose 'Control Panel', 'Network', 'Add Software', 'Remoteboot Service',
    and then put NT server CD or disk to install Remoteboot Service.


Note:
    To install RPL server, you must install DLC & NETBEUI protocols in your
    NT server first.

2. Install MS-DOS files for Remoteboot workstation.

    copy all the MS-DOS 6.22 files to
        ----->\\systemroot\rpl\rplfiles\binfiles\dos622
    copy c:\dos\*.* \\systemroot\rpl\rplfiles\binfiles\dos622
    attrib -s -h c:\io.sys
    attrib -s -h c:\msdos.sys
    copy c:\io.sys \\systemroot\rpl\rplfiles\binfiles\dos622
    copy c:\msdos.sys \\systemroot\rpl\rplfiles\binfiles\dos622
    copy c:\command.com \\systemroot\rpl\rplfiles\binfiles\dos622
    attrib +s +h c:\io.sys
    attrib +s +h c:\msdos.sys

3. Create Remoteboot configuration for new adapter.

3.1 Copy the MS-DOS device driver(NDIS2) for the Ethernet Adapter to the
    \\systemroot\rpl\bblock\ndis directory.
    for example: MXNICF.DOS NDIS2 driver for the PRO120 100/10 Mbps PCI Bus 
                 Fast Ethernet Adapter

3.2 Make a directory \\systemroot\rpl\bblock\netbeui\pci, and then create
    pci.cnf, protocol.ini files in this directory. The temperates for
    pci.cnf & protocol.ini are loacated on the \Bootrom directory in this
    driver diskette.

Sample for PCI.CNF:

; DOS on PCI Ethernet
BASE D0H
RPL BBLOCK\RPLBOOT.SYS
LDR BBLOCK\RPLSTART.COM ~
DAT BBLOCK\NETBEUI\PCI\PROTOCOL.INI          ;must match with 3.2 setting
DRV BBLOCK\RPLDISK.SYS ~ ~ ~
EXE BBLOCK\RPLPRO1.COM ~ 2 ~
EXE BBLOCK\I13.COM ~ ~ ~
EXE BBLOCK\RPLBIND2.EXE ~ ~
EXE BBLOCK\PROTMAN.EXE ~ ~
EXE BBLOCK\RPLBIND1.EXE ~ ~
;DRV BBLOCK\IPXNDIS.DOS ~ ~ ~
;DRV BBLOCK\TCPDRV.DOS /I:C:\LANMAN.DOS ~ ~
EXE BBLOCK\NETBEUI\NETBEUI.EXE ~ 10 ~
DRV BBLOCK\NDIS\MXNICF.DOS ~ ~ ~             ;must match with driver
DRV BBLOCK\PROTMAN.DOS /I:C:\LANMAN.DOS ~ M


Sample for PROTOCOL.INI:

[protman]
  drivername = protman$
  dynamic = yes
  priority = netbeui

[netbeui_xif]
  drivername = netbeui$
  bindings = pci_nif
  names = 6
  ncbs = 12
  packets = 20
  pipeline = 10
  sessions = 6
  stacksize = 512
  lanabase = 0

[xnsnb_xif]
  drivername = xnsnb$
  bindings = pci_nif
  load = xnsnb[cbr]
  lanabase = 1

[xnstp_xif]
  drivername = xnstp$
  bindings = pci_nif
  load = xnstp[ub]
  lanabase = 1

[tcpip_xif]
  drivername = TCPIP$
  disabledhcp = (TCPIP_NO_DHCP)
  ipaddress0 = (TCPIP_ADDRESS)
  subnetmask0 = (TCPIP_SUBMASK)
  defaultgateway0 = (TCPIP_GATEWAY)
  tcpsegmentsize = 1450
  tcpwindowsize = 1450
  nbsessions = 6
  load = tcptsr[c],tinyrfc[c],emsbfr[cr]
  unload = "unloadt /notsr[dc]"
  bindings = pci_nif
  lanabase = 1

[ipx_xif]
  drivername = ipx$
  load = ipxmark[u],ipx[u]
  unload = ipxrel[c]
  bindings = pci_nif
  lanabase = 1

[msdlc_xif]
  drivername = msdlc$
  bindings = pci_nif
  load = msdlc[ub]
  unload = msdlc[u]

[pci_nif]
  drivername = MXNICF$           ;must match with driver

3.3 Use RPLCMD utility to add a BBLOCK record for new adapter
    Under MS-DOS Prompt, type:
       1. C:>Net Start RemoteBoot
       2. C:>RPLCMD
3.4 You must follow the direction displayed on the screen
    Adapter Boot Config Profile Service Vendor Wksta [Quit] V
    Add Del Enum: A
    VendorName=xxxxxx(The first three Ethernet ID)
    Vendor Comment=

    Adapter Boot Config Profile Service Vendor Wksta [Quit] B
    Add Del Enum: A
    BootName=Dosx
    VendorName=xxxxxx(The first three Ethernet ID)
    BbcFile=Bblock\netbeui\Pci\Pci.cnf
    BootComment=Name of this Adapter
    WindowsSize=0

    Adapter Boot Config Profile Service Vendor Wksta [Quit] C
    Add Del Enum: A
    ConfigName=Dos622x
    BootName=Dosx
    DirName=Dos
    DirName2=Dos622
    FitShared=Fits\Dos622.fit
    FitPersonal=Fits\Dos622p.fit
    ConfigComment=Dos 6.22 <Adapter name>
    DirName3=
    DirName4=

3.5 Shutdown Windows NT Server, and reboot it.

4.  Log into NT server as Administrator.

5.  Satrt RemoteBoot Service and Remoteboot manager.

5.1 Under MS-DOS Prompt, type:
      C:>Net Start Remoteboot

5.2 In the 'Network administrator' group, choose 'Remoteboot Manager' and
    then:
  1. Choose 'Remoteboot', 'New Profile' to create Profile Name.
  2. Add new workstation for this Ethernet Adapter and choose PCI Profile file.

Note:
  If the Node ID of Workstation does not match with your profile file, you can
  use "Convert Adapters" in Remoteboot menu of Remoteboot Manager to configure
  or create the Profile file.