1. mx.exe Driver
2. LANLSP.TXT File Contents

LANLSP.TXT Driver File Contents (mx.exe)

	    
                  PRO120 100/10 Mbps PCI Fast Ethernet Adapter
                               NDIS MAC Driver for
            DOS LAN Requester for LSP & OS/2 Communication Manager 1.0
                               Installation Guide
            =========================================================== 


Content of the file
===================
 A.) DOS LAN Requester for LSP V1.30 to V1.37 Installation.
 B.) OS/2 Communication Manager 1.0 Installation.


A.) DOS LAN Requester for LSP V1.30 to V1.37 Installation Procedure
===================================================================
 1. Insert the IBM LAN Support Program (LSP) Version 1.30 (or 1.31 to 1.37)
    Diskette into your floppy drive (drive A: or B:).

 2. Type the following from your DOS prompt and press <Enter>:

    A:>dxmaid

 3. The screen will display the IBM logo. Press <Enter> twice until the
    "Environment Information" appears on screen.

 4. Respond to the screen prompts, specifying the following values for each
    field:

          Use the <Space Bar> to toggle between choices:
          Configuration for this computer?          Yes
          Use existing configuration information?   Yes
          Do you have adapter option diskettes?     Yes
          Are you configuring for two adapters?     No
          Do you need 802.2 interface support?      No

          Type change as needed to drive and directory information below:

          Source for LSP                           A:\
          Target for new configuration             C:\lsp
 
 5. Make sure that the values given above are correct. Press <Enter> to store
    your choices.

 6. Insert the Driver Diskette in your source drive. Specify the path and press
    <Enter> to proceed.  Examples:

      A:\NDIS20\DOS

 7. Press <Enter> to copy the necessary drivers from the Driver Diskette to
    your target directory in the hard disk.

 8. Follow screen instructions to complete the process. Simply pressing <Enter>
    for each screen display will select the default options.  Press <Enter> 
    three times, until you reach the display prompting you to insert the LSP 
    diskette.

 9. Insert the LSP diskette as prompted. Press <Enter> to acknowledge 
    completion of the action.

10. A screen showing the current configuration detected will be displayed.
    It should show "PCI Fast Ethernet adapter" and the protocols
    already selected (i.e., "IBM IEEE 802.2" and "IBM OS/2 NETBIOS").


11. Press <F4> to save the new configuration. This completes the LSP
    installation.

    NOTE: You should have defined the minimum of 20 files in CONFIG.SYS file,
          i.e. FILES=20, to run the software properly. Change the FILES line
          using the text editor if needed.

          If installing LSP for the first time, you should complete the
          installation by typing INSTALL and following the further instructions
          on screen.
  
12. Use a text editor to edit the CONFIG.SYS file.  Specify at least 20 files
    in the FILES= line. Modify it to the following:

      FILES=20

13. Save the configuration and reset your computer.

14. Insert the DOS LAN Requester Install Diskette into your floppy drive.

15. Type the following and press <Enter>:

      INSTALL    <Enter>

16. The IBM logo will again appear on the screen.  Press <Enter> to move on to
    the next screen.

17. Follow screen instructions, press <Enter> to move from screen-to-screen
    until you are prompted to indicate the pathname of the DOS LAN Requester
    directory.

      TIP: After the IBM logo appears on the screen, press <Enter> twice to
           reach this screen.

18. Specify the pathname for the DOS LAN Requester directory (C:\DOSLAN is the
    default).  Then press <Enter> to continue.

19. The program will ask you for the services that you require.

20. Highlight the appropriate option. Select either "Send messages" or "Send,
    View, Edit, and Log message" option.

      TIP: Normally, second option "Send, View, Edit and Log message" is
           selected.

21. Specify the PC's ID and domain ID.  The domain ID is the domain server ID.
    It should be the same as all workstations of the network.

22. Follow screen prompts to complete the installation.


B.) Communication Manager 1.0 Installation Procedure
====================================================
 1. Copy the MXNICF.OS2 and MXNICF.NIF files in the driver diskette to your
    C:\IBMCOM\MACS directory.

 2. Select the PRO120 100/10 Mbps PCI Ethernet Adapter and choose the
    appropriate protocols.

 3. Check that the CONFIG.SYS file includes the following line:

     DEVICE = C:\IBMCOM\MACS\MXNICF.OS2

4.  Shut down your OS/2 system, and then reboot your PC.