Please note that the information in this file is written in two languages.
Refer to Section A for English version and Section B for German version.
Section A :
*********************************************************************
* Additional Information *
* *
* AZT IDE CD-ROM Drive Installation Disk ver 2.50 *
*********************************************************************
This file contains additional information about the CD-ROM drive
installation software that was not available at printing time.
General Information
===================
Standard IDE supports up to a maximum of two IDE interfaces. Each IDE
interface can support up to a maximum of two devices, i.e. either 2 hard
disks, 2 CD-ROM drives or a combination of 1 hard disk & 1 CD-ROM drive.
The port address for Primary & Secondary IDE interface is at 1F0H & 170H
respectively.
Primary IDE interface refers to the interface (at 1F0H) on your system
where the IDE hard disk is connected (it can be built-in on the system
motherboard or on a separate I/O card). Secondary IDE interface (at 170H)
refers to the IDE interface on a separate interface card (e.g. the
interface card bundled with this CD-ROM drive, on-board Secondary IDE
interface or the interface on the sound card).
CD-ROM Drive Configuration
==========================
Please note that the IDE CD-ROM drive is factory configured to Single/Slave
drive setting. Therefore, the following points are to be observed during
the installation of the CD-ROM drive :
1.) If you are connecting the CD-ROM drive directly to the provided
interface card or your system's on-board Secondary IDE interface,
no jumper setting is required on either the CD-ROM or hard disk drive.
If the on-board Secondary IDE interface has a hard disk connected,
ensure that it is configured to Master drive setting. Please refer
to your hard disk reference manual for more information.
2.) If your Sound Card has an IDE interface, please install the CD-ROM
drive through the interface on the sound card. Please ensure that the
jumper setting on the sound card is properly configured to IDE CD-ROM
interface. For more information, refer to your sound card user's
manual.
3.) If you are connecting the CD-ROM drive and the hard disk together
through the on-board Primary IDE interface,
a.) Please ensure that your hard disk is configured to Master drive
setting. For more information, please refer to your hard disk
reference manual.
b.) Please also make sure that the following statement is in the
[386Enh] section in the SYSTEM.INI file under WINDOWS directory.
[386Enh]
32bitdiskaccess=OFF
4.) If you are connecting two CD-ROM drives directly to the provided
interface card or your system's on-board Secondary IDE interface,
ensure that one CD-ROM drive is configured to Master drive and the
other to Slave drive setting. Please refer to the CD-ROM drive manual
for more information on how to configure the drives.
Section B :
*************************************************************************
* Zustzliche Informationen *
* *
* AZT IDE CD-ROM Laufwerk Ver 2.50 *
*************************************************************************
In dieser Datei finden Sie zustzliche Informationen zur CD-ROM Laufwerk
Installationssoftware, die bei Drucklegung nicht verfgbar war.
Allgemeine Informationen
========================
Standard IDE untersttzt maximal zwei IDE Schnittstellen. An jeder IDE
Schnittstelle knnen maximal zwei Gerte angeschlossen sein, z.B. zwei
Festplattem zwei CD-ROM Laufwerke oder eine Kombination aus einer
Festplatte und einem CD-ROM Laufwerk. Die Portadresse fr ein primres IDE
Interface ist 1F0H und fr ein sekundres IDE Interface 170H.
Das primre IDE Interface ist der Anschluá (bei Adresse 1F0H), an dem Ihre
Festplatte(n) angeschlossen ist. Es kann auf dem Mainboard oder auf einer
Controllerkarte eingebaut sein. Ein sekundres IDE Interface (bei Adresse
170H) ist dann in Ihrem System vorhanden, wenn Sie in Ihrem System vier
AT-Bus Festplatten installieren knnen. Sie finden es dann ebenfalls auf
dem Mainboard oder auf der Controllerkarte. Ein zustzliches sekundres IDE
Interface kann auch das auf bestimmten Soundkarten (z.B. Aztech WaveRider
32+) eingebaute sekundre IDE Interface oder das auf der optionalen
Schnittstellenkarte zum IDE CD-ROM Laufwerk enthaltene Interface sein.
CD-ROM Laufwerk Konfiguration
=============================
Beachten Sie bitte, daá das IDE CD-ROM Laufwerk ab Werk als Single/Slave
Laufwerk konfiguriert ist. Bei der Installation dieses Laufwerks mssen
folgende Punkte beachtet werden:
1.) Wenn Sie das CD-ROM Laufwerk direkt an der optionalen Interfacekarte
von Aztech oder an einem anderen sekundren Interface in Ihrem PC
anschlieáen, so brauchen keine Jumper verndert zu werden. Wenn am
sekundren IDE Interface in Ihrem System bereits eine Festplatte
installiert ist, muá diese als Master konfiguriert sein. Die korrekte
Jumpereinstellung entnehmen Sie bitte der Anleitung Ihrer Festplatte.
2.) Wenn an Ihrer Soundkarte ein IDE Interface vorhanden ist, schlieáen
Sie das CD-ROM Laufwerk bitte dort an. Stellen Sie sicher, daá mit
dem Jumper auf der Soundkarte die IDE Schnittstelle eingeschaltet
ist. Weitere Hinweise finden Sie im Soundkartenhandbuch.
3.) Wenn Sie das CD-ROM Laufwerk zusammen mit einer Festplatte an einem
primren IDE Interface in Ihrem System anschlieáen wollen, dann
beachten Sie folgende zwei Punkte:
a) Stellen Sie sicher, daá die (einzige) Festplatte als Master
konfiguriert ist. Die korrekte Jumpereinstellung entnehmen
Sie bitte der Anleitung Ihrer Festplatte.
b) Stellen Sie auch sicher, daá die folgende Zeile im Abschnitt
[386Enh] der SYSTEM.INI Datei im WINDOWS Verzeichnis steht:
[386Enh]
32BitDiskAccess=OFF
4.) Wenn Sie zwei IDE CD-ROM Laufwerke an einem vorhandenen sekundren
IDE Interface in Ihrem System anschlieáen wollen, so muá das eine
CD-ROM Laufwerk als Master umkonfiguriert werden, whrend das andere
weiter als Slave konfiguriert bleibt. Informationen zu diesem Thema
finden Sie in Ihrem CD-ROM Handbuch.
In diesem Fall kopieren Sie die Zeile DEVICE=(Pfad)SGIDECD.SYS...
in der Datei CONFIG.SYS und editieren die zweite Zeile, so daá die
Namen der Laufwerke unterschiedlich sind. Die Zeilen knnen dann
z.B. so aussehen:
(Config.sys)
DEVICE=C:\WR32\DRIVERS\SGIDECD.SYS /D:MSCD001
DEVICE=C:\WR32\DRIVERS\SGIDECD.SYS /D:MSCD002
Editieren Sie dann die Zeile mit dem Aufruf von MSCDEX.EXE in der
Startdatei AUTOEXEC.BAT folgendermaáen:
(Autoexec.bat)
C:\DOS\MSCDEX.EXE /D:MSCD001 /D:MSCD002
Hier reicht also eine Zeile, in der beide Namen genannt werden. Der
Pfad C:\DOS ist hier nur ein Beispiel und kann in Ihrer Autoexec.bat
Datei anders lauten. Auch knnen weitere Parameter folgen. Lassen Sie
diese, wie sie sind, fgen Sie lediglich /D:MSCD002 zustzlich ein.
--- Ende der Datei ---
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.