FTP.TXT Driver File Contents (OfficeLan10-100_II.zip)

    Driver Installation - FTP PC/TCP v2.2 for DOS
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

  Siemens OfficeLAN PCI 10/100 TX Fast Ethernet Adapter

  FTP PC/TCP v2.2 for DOS (Packet Driver)
  INSTALLATION GUIDE


=============================================================================
CONTENTS
=============================================================================

*  Important Considerations

*  Files Provided

*  Device Driver Installation Guide

=============================================================================
IMPORTANT CONSIDERATIONS
=============================================================================

*  This driver supports my PCI 10/100 TX Fast Ethernet Adapters.

*  This driver conforms to the FTP software Inc. PC/TCP Packet Driver
    Specification revision 1.09

*  Make sure that the adapter line speed matches the speed of
    the hub to which it is attached.

=============================================================================
FILES PROVIDED
=============================================================================

*  FEPD.COM              FTP Packet Driver

=============================================================================
DEVICE DRIVER INSTALLATION GUIDE
=============================================================================

1. Introduction:
    This document describes the procedure to setup the Packet driver for
    my PCI 10/100 TX Fast Ethernet Adapters.

2. Location of Driver:

             \PKTDRV\FEPD.COM

3. Sample Configuration Files:

      %% AUTOEXEC.BAT %%
        FEPD              (Since the default software interrupt is 0x60 )
        or
        FEPD  <PD_INT_NO> (Interrupt entry should be between 0x60 - 0x80)


4. Notes:

      1. Load the packet driver using the software interrupt and any
         optional switches if required.

         Usage: FEPD [options] <software_int_no>

         Example: FEPD -n 0x7e

      2. Executing FEPD need no parameter. When identify the adapter, FEPD
         will automatically sense the line speed (10Mbps or 100Mbps),
         read configurations from PCI BIOS and give 0x60 as default
         software interrupt number.
         Software interrupt number is changable by user's favorite. Admitted
         range is between 0x60 - 0x80.
         Other options list below:

         -sn ,n=0 ~ 5, Set media speed
              n=0      AutoDetect (Default Value) 
              n=1      10M TP  
              n=2      10M TP Full-Duplex 
              n=3      10M BNC    ;; The card doesn't support this option
              n=4      100M Tx 
              n=5      100M Tx Full-Duplex 
         -h            On Line Help. 
         -n            Convert ETHERNET_II Header to IEEE 802.3.
         -w            Let Packet Driver Run Under WINDOWS. 
         -u            Unload The Packet Driver. 

      3. Run FEPD.COM, the screen will appear following message:

         Siemens OfficeLAN PCI 10/100 TX Fast Ethernet Adapter Packet Driver
         (C) Copyright 1997-1998 Siemens Data Communication, Ltd. 
         All Rights Reserved.


         Ethernet Address is : (00:A0:CC:66:00:03)
         Packet Driver Interrupt Number : 0x60
         Hardware Interrupt Number : 5
         Base I/O Address : 0xD000
         Medium Type is : 100Mbps Tx
         Packet Driver is loaded at segment : 29C2

=============================================================================

This software and documentation have restricted rights: their use, duplication,
or disclosure by the Government is subject to the restrictions in:

*  DFARS 252.227-7013
    Subparagraph (c) (1) (ii)
    Rights in Technical Data and Computer Software clause

*  FAR 52.227-14
    Alternate III
    Rights in Data -- General clause

*  FAR 52.227-19
    Subparagraphs (c) (1) and (2)
    Commercial Computer Software -- Restricted Rights clause


Other product and company names are registered trademarks or trademarks of
their respective holders.

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web2, load: 0.79