NW_CLN32.TXT Driver File Contents (OfficeLan10-100_II.zip)

    Driver Installation - Novell NetWare Client 32 for DOS/Win95
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

  Siemens OfficeLAN PCI 10/100 TX Fast Ethernet Adapter

  Novell NetWare Client 32 Driver
  INSTALLATION GUIDE


=============================================================================
CONTENTS
=============================================================================

*  Introduction

*  System Requirements

*  Files Provided

*  Hardware Installation Guide

*  Driver Installation of NetWare Client 32 for Windows 95
      - Install the NetWare Client 32 for Windows 95
      - Installation Procedures

*  Driver Installation of NetWare Client 32 for DOS/Windows 3.1x
      - Installtion Procedures
      - Documentation
      - Descriptions of Configurations

*  Setting Driver Parameters


=============================================================================
Introduction
=============================================================================

  This document describes the procedures to install Novell
   NetWare Client 32 driver under DOS, Microsoft Windows 3.1x,
   or Microsoft Windows 95.


=============================================================================
System Requirements
=============================================================================

Hardware Requirements:

*  IBM-compatible personal computer (PC), 80486 or higher with PCI bus

*  This adapter

Firmware Requirements:

*  Fully compliant Rev. 2.0 or higher PCI BIOS supplied with the PC

Software Requirements:

*  MS-DOS v3.0 or higher


=============================================================================
Files Provided
=============================================================================

*  L100.LAN     Novell NetWare Client 32 driver
*  L100.LDI     The setup file for NetWare Client 32 for DOS/Windows
*  L100NWC.INF  The setup file for NetWare Client 32 for Windows 95


=============================================================================
Hardware Installation Guide
=============================================================================

*  See the User Guide for complete installation instructions.

*  When installing my card in a PCI computer, make sure the slot
    you select supports bus master operations.

*  No specialized setup is necessary for motherboards with automatic
    PCI parameterization (most new PCs support it).

*  For motherboards with bus master jumpers and interrupt jumpers for
   PCI slots:

   1.  Using the appropriate motherboard jumper, enable bus master
        operations for the selected PCI slot.

   2.  Using the appropriate motherboard jumper, select the interrupt
        to the selected PCI slot.

   3.  Using your computer setup menu:

        *  Enable the bus master on the PCI slot.

        *  Enable I/O on the PCI slot.

        *  Define the interrupt number on the PCI slot.


=============================================================================
Driver Installation of NetWare Client 32 for Windows 95
=============================================================================

 A) Install the NetWare Client 32 for Windows 95

   1. Run the SETUP.EXE program for NetWare Client 32 for Windows 95.
       It is located in the \ENGLISH subdirectory of the package.

 B) Installation Procedures

   1. Insert the driver diskette into the floppy drive (for ex : A:).

   2. Open the "Control Panel", and then click the "Network" icon.

   3. When the "Network" dialog box pops up, choose the "Configuration"
       item, and click the "Add..." button to add adapter.

   4. When the "Select Network Component Type" dialog box pops up,
       select the "Adapter" item, and then press "Add" button.

   5. When the "Selected Network Adapters" dialog box pops up, click
       the "Have Disk" button.

   6. When the "Install From Disk" dialog box pops up. specify the
       path to driver, and then click the "OK" button.

         for example :   A:\CLIENT32

   7. Choose the adapter, and specify the related parameters of driver.

   8. The installation of NetWare Client 32 for Windows 95 completed.
       Reboot the computer to make changes in effect.


=============================================================================
Driver Installation of NetWare Client 32 for DOS/Windows 3.1x
=============================================================================

 A) Installation Procedures

   1. Run the INSTALL.EXE file in the NetWare Client 32 software.

   2. Select the NetWare Client 32 products you want to install
       on the computer from the list below :

        [X] NetWare Client 32 for DOS
        [X] NetWare Client 32 for Windows
        [ ] NetWare TCP/IP protocol stack
        [ ] NetWare IP (TCP/IP Required)
        [ ] Desktop SNMP
        [ ] HOSTMIB for SNMP (SNMP Required)
        [ ] NetWare TSA for SMS

      Note :
        The default items are the "NetWare Client 32 for DOS" and
         "NetWare Client 32 for Windows".

   3. When the "Customize Support for Windows" menu pops up, choose
        anyone you want to install.

   4. When the "Select LAN Driver Type" menu pops up, choose the
        "32-bit LAN drivers" item.
 
   5. When the "32-Bit Network Board Drivers" menu pops up, choose
        the "USER SPECIFIED 32 BIT DRIVER" item.

   6. When the "Insert the Driver Disk" menu pops up, insert the
       driver diskette and then specify the path to the driver.

       for example:     A:\CLIENT32

   7. When the "32-Bit Network Board Drivers" menu pops up, choose
       the adapter.

   8. The <OPTIONAL> Specify the settings for the adapter.

   9. When the "Installation Configuration Summary" menu pops up,
       check whether the settings are correct, or need to modify.

    Modify AUTOEXEC.BAT and CONFIG.SYS      [YES]

    Client Directory:       C:\NOVELL\CLIENT32
    Windows Directory:      C:\WINDOWS
    LAN driver type:        32-bit LAN drivers
    LAN driver:             Siemens OfficeLAN PCI 10/100 TX Fast Ethernet Adapter

  10. NetWare Client 32 for DOS will copy these files to the computer
       and modify the configuration files to match your setting.

 
 B) Documentation
 
   1. If you want to load the multiple frame types, you will get the
       following message during the driver loading:

        "Do you want to load another frame type for a previously
         loaded board?  Y/N ".

      You can add the slot number to the command line in the
       STARTNET.BAT to avoid it.

   2. Make sure that the FIRST NETWORK DRIVE = F statement is added
       in the NET.CFG file under the "NetWare DOS Requester" section.

   3. Check the LASTDRIVE setting in the CONFIG.SYS file, it must
        have the LASTDRIVE=Z statement under NetWare Client 32 for DOS.
       

 C) Descriptions of Configurations

   The following descriptions are the sample files after the
    installtion of NetWare Client 32 for DOS :

      NET.CFG
      =======

        NetWare DOS Requester
          FIRST NETWORK DRIVE F
          NETWARE PROTOCOL NDS BIND

        Protocol IPX
          IPX SOCKETS 40

      STARTNET.BAT
      ============

        SET NWLANGUAGE=ENGLISH
        C:\NOVELL\CLIENT32\NIOS.EXE
        LOAD C:\NOVELL\CLIENT32\LSLC32.NLM
        LOAD C:\NOVELL\CLIENT32\CMSM.NLM
        LOAD C:\NOVELL\CLIENT32\ETHERTSM.NLM
        LOAD C:\NOVELL\CLIENT32\L100.LAN SLOT=1 FRAME=Ethernet_802.2
        LOAD C:\NOVELL\CLIENT32\L100.LAN SLOT=1 FRAME=Ethernet_802.3
        LOAD C:\NOVELL\CLIENT32\IPX.NLM
        LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM

  
=============================================================================
Setting Driver Parameters
=============================================================================

  This driver provides the parameters to set the functionality of
   adapter.  The parameters are listed as below :

   SLOT     The driver uses the slot number to identify the adapter.
            That is, the first adapter is considered to be in the slot 1,
              the next in slot 2, and so on.

            If you want to load those multiple frame types, you
              should specify the slot number of the adapter.

   MEDIA    Specify the media type of adapter to use (between 0 to 5).

      0   -   auto-sense the media, including run-time auto-sense (default)
      1   -   100Base-Tx Half-Duplex mode
      2   -   100Base-Tx Full-Duplex mode
      3   -   10Base-T Half-Duplex mode
      4   -   10Base-T Full-Duplex mode
      5   -   10Base-2 (BNC)

   THRESHOLD Specify the Tx Threshold mode of adapter to use (between 0 to 6).

      0   -   Store and Forward (default)
      1   -   Threshold 36 Bytes
      2   -   Threshold 72 Bytes
      3   -   Threshold 96 Bytes
      4   -   Threshold 128 Bytes
      5   -   Threshold 160 Bytes
      6   -   Threshold 256 Bytes

NOTE:  The TxThreshold lets you choose the number of bytes read from the host
        memory into the transmit FIFO before the transmission. If the frame
        length is less than the threshold value, the adapter will start to
        transmit after a full frame is in the FIFO. The performance is better,
        if the smaller value is chosen. But if you have compatible problem, the
        Store and Forward or the bigger value is recommended.


Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web5, load: 0.57