Driver Installation - IBM PC LAN Program Environment
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Siemens OfficeLAN PCI 10/100 TX Fast Ethernet Adapter
IBM PC LAN Program Environment
INSTALLATION GUIDE
=============================================================================
CONTENTS
=============================================================================
* Important Considerations
* Files Provided
* Device Driver Installation Guide
=============================================================================
IMPORTANT CONSIDERATIONS
=============================================================================
* This driver supports the Siemens OfficeLAN PCI 10/100 TX Fast Ethernet
Adapter.
* This driver conforms to the Network Driver Interface Specification (NDIS)
v2.0.1 defined by Microsoft/3Com. The driver has been tested with
Microsoft LAN Manager, 3Com 3+Open, IBM LAN Server, IBM PC LAN
Program, DEC Pathworks, and other NDIS-compatible network operating
systems and protocol stacks.
* Make sure that the adapter line speed matches the speed of
the hub to which it is attached.
* The PROTOCOL.INI file contains configuration information.
=============================================================================
FILES PROVIDED
=============================================================================
* L100.DOS DOS NDIS2 driver
* PROTOCOL.INI Driver binding information and operational parameters
=============================================================================
DEVICE DRIVER INSTALLATION GUIDE
=============================================================================
The following instructions are for installing the PC LAN program on a
workstation. The section after this gives instructions for installing PC LAN
on a server. Both procedures use the LAN Support Program (LSP) for the
installation process.
* Installing PC LAN on a Workstation
1. At the DOS prompt, insert the IBM LAN Support Program (LSP) v1.3x
diskette.
2. Type: DXMAID
3. Press [Enter] three times.
The Environment Information screen appears.
4. Specify the values that follow for the fields on this screen. Use the
spacebar to cycle through the available options for each field.
For LSP v1.30 and v1.33:
Configuration for this computer? Yes
Use existing configuration information? No
Do you have adapter option diskettes? Yes
Are you configuring for two adapters? No
Source for LSP A:\
Target for new configuration C:\LSP
For LSP v1.35:
Are you updating an existing configuration? No
Do you have driver diskettes? Yes
Target for LSP: C:\LSP
CONFIG.SYS to update: C:\CONFIG.SYS
AUTOEXEC.BAT to update: C:\AUTOEXEC.BAT
5. Press [Enter] to accept these selections.
The program prompts you to install the "option" diskette.
6. Insert the ConfigDisk in your floppy drive and specify the path:
A:\NDIS\DOS
7. Press [Enter].
The files are copied from the ConfigDisk to the target directory on the
hard disk.
8. For LSP v1.30 and v1.33 users, press [Enter] two times.
For LSP v1.35 users, press [Enter] once only.
The files are copied from the ConfigDisk tothe target directory on the
hard disk.
9. When prompted, re-insert the LSP diskette and press [Enter].
The Current Configuration screen appears with :
"Siemens OfficeLAN PCI 10/100 TX Fast Ethernet Adapter"
10. Press [F4].
LSP is installed.
11. Use a text editor to edit the CONFIG.SYS file, specifying at least
20 files in the FILES= line.
Example:
files=20
12. Save your CONFIG.SYS file and reboot your system.
13. If you are using DOS v5.0 or later, type at the DOS prompt:
SETVER CIP_MAIN.EXE 5.00
14. Press [Enter].
15. Reboot your system.
16. Insert the PC LAN Install diskette in your computer floppy drive.
17. Type: INSTALL
18. Press [Enter].
19. Press [Enter]three more times.
20. Select the function level for the workstation:
Base Services Only
Extended Services
In most cases you will select "Extended Services".
21. Specify "Workstation".
22. Specify one of the following options:
Send messages
Send, receive, and log messages
In most cases you will select "Send, receive, and log messages".
23. Specify the target path for the PC LAN files. The default is C:\DOS.
24. Specify the machine ID and the domain ID. The domain ID must
be the domain server ID, and it must be the same for all workstations
on the network.
25. Follow the prompts to complete the installation until you reach the
Change System Configuration File screen. Usually, you should
accept the default for the system configuration file.
The Change System Batch File screen appears. Usually you should
accept the default.
* Installing the PC LAN Program on a Server
The following section provides instructions for installing PC LAN
on a server. This procedure uses the LAN Support Program (LSP) for the
installation process.
1. At the DOS prompt, insert the LSP diskette.
2. Type: DXMAID
3. Press [Enter].
4. Press [Enter] twice.
The Environment Information screen appears.
5. Specify the values that follow for the fields on this screen. Use the
spacebar to cycle through the available options for each field.
Configuration for this computer? Yes
Use existing configuration information? No
Do you have adapter option diskettes? Yes
Are you configuring for two adapters? No
Source for LSP A:\
Target for new configuration C:\LSP
6. Press [Enter] to accept these selections.
The program prompts you to install the "option" diskette.
7. Insert the ConfigDisk in your floppy drive and specify the path:
A:\NDIS\OS2.
8. Press [Enter].
The files are copied from the ConfigDisk to the target directory on
the hard disk.
9. Press [Enter] three times.
10. When prompted, re-insert the LSP diskette and press [Enter].
The Current Configuration screen appears with the Ethernet adapter
and protocols already selected.
11. Press [F4].
LSP is installed.
12. Use a text editor to edit the CONFIG.SYS file, specifying at least
20 files in the FILES= line.
Example:
files=20
12. Save your CONFIG.SYS file and reboot your system.
13. Insert the PC LAN Install diskette in your computer floppy drive.
14. Type: INSTALL
15. Press [Enter].
16. Press [Enter] three more times.
17. Select the function level for the workstation:
Base Services Only
Extended Services
In most cases you will select "Extended Services".
18. Specify "Server".
19. Specify one of the following options:
Send messages
Send, receive, and log messages
In most cases you will select "Send, receive, and log messages".
20. Specify the target path for the PC LAN files. The default is C:\DOS.
21. Specify the machine ID and the domain ID. The domain ID must
be the domain server ID, and it must be used by all workstations
on the network to communicate with the server.
25. Follow the prompts to complete the installation until you reach the
Change System Configuration File screen. Usually, you should
accept the default for the system configuration file.
The Change System Batch File screen appears. Usually you should
accept the default.
=============================================================================
This software and documentation have restricted rights: their use, duplication,
or disclosure by the Government is subject to the restrictions in:
* DFARS 252.227-7013
Subparagraph (c) (1) (ii)
Rights in Technical Data and Computer Software clause
* FAR 52.227-14
Alternate III
Rights in Data -- General clause
* FAR 52.227-19
Subparagraphs (c) (1) and (2)
Commercial Computer Software -- Restricted Rights clause
Other product and company names are registered trademarks or trademarks of
their respective holders.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.