1. Dynex_DX-E201_driver_manual.exe Driver
2. NW312.TXT File Contents

NW312.TXT Driver File Contents (Dynex_DX-E201_driver_manual.exe)

Server Driver for NetWare 3.12

Introduction:
-------------
This document describes the procedure to install the NetWare V3.12
server driver for Dynex DX-E201 CardBus PC Card.

   Location of Driver:     \NWSERVER\312\DXE201.LAN

Getting Start:
--------------

  1. For the PC that installing EMM386.EXE in the CONFIG.SYS.
     Please make sure the memory range D000-D7FF is excluded.

     Ex:
         DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-D7FF

  2. Copy <PATH>\ENABLER\*.* files from released disk into your
     hard disk.
  
      Ex:                                                      
          copy E:\ENABLER\*.* C:\ENABLER


  3. Add a line

     @CALL C:\ENABLER\CBEN.BAT

     on the first line of AUTOEXEC.BAT file.

Installation Procedure:
-----------------------
Before you start with the installation process, make sure that
the Novell NetWare v3.12 server is properly installed.
Similarly, your adapter should also be properly installed in your server.

  1. Make a sub-directory NLMS.OLD under <SRVPATH> directory which
     includes SERVER.EXE.

     Ex. <SRVPATH> = SRV312.
         >MD \SRV312\NLMS.OLD

  2. Save NBI.NLM, MSM.NLM and ETHERTSM.NLM to NLMS.OLD
     sub-directory.

  3. Insert driver disk into CD-ROM drive.

  4. Copy all provided NLM and LAN files into your dos directory
     which includes SERVER.EXE, and rename NBI31X.NLM and MSM31X.NLM :

     Ex. >COPY E:\NWSERVER\312\NBI31X.NLM C:\SRV312\NBI.NLM
         >COPY E:\NWSERVER\312\MSM31X.NLM C:\SRV312\MSM.NLM
         >COPY E:\NWSERVER\312\ETHERTSM.NLM C:\SRV312
         >COPY E:\NWSERVER\312\DXE201.LAN C:\SRV312

  5. Start the NetWare Server.

     > CD \SRV312
     > SERVER

  6. From the Novell Server side, execute "LOAD INSTALL".  Type:

        LOAD INSTALL

     Select <System Options>
     Select <Edit AUTOEXEC.NCF File>

  7. Add the following commands into the server's AUTOEXEC.NCF file.

     Search Add C:\SRV312

     LOAD NBI.NLM
     LOAD MSM.NLM
     LOAD ETHERTSM.NLM

     LOAD DXE201 SLOT=1 FRAME=Ethernet_802.3 NAME=DXE201_1_E83
     BIND IPX DXE201_1_E83 NET=1111

     LOAD DXE201 SLOT=1 FRAME=Ethernet_802.2 NAME=DXE201_1_E82
     BIND IPX DXE201_1_E82 NET=1113

     LOAD DXE201 SLOT=1 FRAME=Ethernet_SNAP  NAME=DXE201_1_ESP
     BIND IPX DXE201_1_ESP NET=1115

     LOAD DXE201 SLOT=1 FRAME=Ethernet_II    NAME=DXE201_1_EII
     BIND IPX DXE201_1_EII NET=1117

     Note: The SLOT parameter should be set as the number of the PCI slot
           on which DFE-DXE201 resides.

  8. Restart the server again.


NOTES:
------

  1. Installing Multiple LAN Adapters:

     The keyword "SLOT" is provided for multiple LAN adapters in a
     single server by the driver DXE201.LAN. So, add "SLOT" in LOAD
     commands. For example:

     LOAD DXE201 SLOT=1 FRAME=Ethernet_802.2 NAME=LAN_A
     BIND IPX TO LAN_A NET=111
     LOAD DXE201 SLOT=2 FRAME=Ethernet_802.2 NAME=LAN_B
     BIND IPX TO LAN_B NET=222

  2. Use keyword AUTO, 100FULL, 100HALF, 10FULL, 10HALF to specify the
     media type of the DFE-DXE201.

     For example:

     ; Specify AUTO-DETECT
     LOAD DXE201 AUTO FRAME=Ethernet_802.2 NAME=LAN_A
     BIND IPX TO LAN_A NET=111

     ; Specify 100Mbps, Half-duplex
     LOAD DXE201 100HALF FRAME=Ethernet_802.2 NAME=LAN_A
     BIND IPX TO LAN_A NET=111

     The default media type is auto-detect(i.e. none of these keywords
     is specified).

  3. Installing One LAN adapter with Multiple Frame Types:

     When binding multiple frame types to one adapter, enter a LOAD
     and BIND statement for each frame type. Each LOAD statement will
     use a different network number on the bind statement.
     It is required to supply a name on each load line in order to avoid
     being prompted for which board to bind IPX to. If you do not
     have the name option in the AUTOEXEC.NCF, it will not execute
     completely without user intervention.

     Example:

     LOAD DXE201 FRAME=ETHERNET_802.3 NAME=DXE201_1_E83
     BIND IPX TO DXE201_1_E83 NET=11111

     LOAD DXE201 FRAME=ETHERNET_802.2 NAME=DXE201_1_E82
     BIND IPX TO DXE201_1_E82 NET=33333

     LOAD DXE201 FRAME=ETHERNET_SNAP  NAME=DXE201_1_ESP
     BIND IPX TO DXE201_1_ESP NET=55555

     LOAD DXE201 FRAME=ETHERNET_II    NAME=DXE201_1_EII
     BIND IPX TO DXE201_1_EII NET=77777

     If problems occur during the binding process, your screen will prompt
     you with error messages. Please refer to your NetWare 386 manual for
     details on these messages.

                                                                 -- End --