CLIENT32.TXT Driver File Contents (ax8814x_netware.zip)

            Installation Guide for Client 32 LAN Driver

 The following items are described in this file,

   Installing Client 32 LAN Driver for WIN 95
   Installing Client 32 LAN Driver for DOS
   Installing Client 32 LAN Driver for WIN 3.1X


 Install LAN adapter driver on Client 32 for Windows 95

   Case 1:

   Installing driver on WIN95 WITHOUT Client 32

     If you have previously installed Novell Netware Client 32 under
     your Windows 95 system, skip this section and see "Case 2" below.

     Install Client 32 From Diskette :
     . Copy the NW88140.INF file to Disk 1 (Setup Disk) of the Client 32
       for Windows 95 software.
     . Copy the AX88140.LAN driver to the Client 32 LAN driver
       diskette (32-bit).
     . Add a new reference line into the "INF Files" section of
       the NWSETUP.INI file.
       Note: NWSETUP.INI can be found on Disk 1, or in the \NOVELL\CLIENT32\
             INSTALL directory after installation.
       Sample of NWSETUP.INI file:
               .
               .
               .
             [INF Files]
             1=NWClient.inf
             2=NWTrans.inf
             3=ODINSUP.inf
             4=NE3200.inf       <--- replace the line to 4=NW88140.INF
             5=NE2000.inf
             6=NE15_21.inf
             7=NE2.inf
             8=NE2_32.inf
               .
               .


     . Shut down the system, add the network adapter, turn on the system.

     . Remove adapters from the Network control panel for any cards that
       are no longer in the system.

     . In "System Settings Change" window, select "No".

     . Continue to install NetWare Client 32.

     . Run the Client 32 install using SETUP.EXE
       ( Check the box to replace NDIS with ODI )
       ( The WIN95 CD will probably be required )

     . In "Select Device" windows, select "" for Manufacturers,
       and select proper model for your network adapter.

     . After installation completed, reboot the machine.

     . Watch WIN95 auto-detect the hardware. The correct new ODI driver
       should be installed.


   Case 2:

   Installing Network Adapter on WIN95 WITH Client 32

     . In Windows 95, change directory to the \Windows\INF.

     . Remove the old NW88140.INF file (if it exists).

     . Create a temporary directory and copy all the files from the
       \Windows\INF directory to this temporary directory.

     . Verify that the copy completed properly and the two directories
       contain the same files.

     . Delete all the files (*.INF) in the \Windows\INF directory.

     . Copy the new NWETHPCI.INF into \Windows\INF directory.

     . Now copy all the files back from the temporary directory you created
       to the \Windows\INF\ directory.

     . NW88140.INF should now be the first one Windows sees in the loading
       process, and be loaded before any others for the same adapter.

     . Remove any adapter from the Network Control Panel, including
       ODINSUP and any asscoiated files.

     . Shut down the system, install the network adapter and turn on the
       system.

     . Watch WIN95 auto-detect the hardware, and select correct new ODI
       driver to be installed. If not, you may select the "Have Disk"
       option for installation, in which case you will be prompted to
       input the path where the driver located:
          ex. A:\CLIENT32.95, if floppy disk is used.
              C:\CLIENT32.95, if hard disk is used.

       You will then be prompted for Client 32 diskettes.

     . Complete the Client 32 installation.



 Install LAN Adapter Driver on Client 32 for DOS/Windows 3.1x

   Case 1:

   Install Driver During Installation of Netware Client 32

     . In DOS environment, run "INSTALL" command.

     . Follow the installation steps of Novell NetWare Client 32.

     . In "Select a LAN Driver Type" window, select "32-bit" LAN drivers.

     . In "32-Bit Network Board Drivers" window, select
       "USER SPECIFIED 32 BIT DRIVER".

     . In "Insert The Driver Disk" window, input the path
       where the LAN driver and .LDI file locate:
          ex. A:\CLIENT32, if floppy disk is used.
              C:\CLIENT32, if hard disk is used.

     . Select the desired parameters, eg. SLOT number....
       and continue the installation procedure.

     . In MS Windows environment, run "SETUP" command.

     . In "ODI Driver Selection" window, select "32 bit" mode
       and "other Boards".

     . Enter the path and filename of the ODI driver in "ODI Driver Path"
       window.

     . Follow the installation setps of Novell NetWare Client 32.

     . After the installation, a STARTNET.BAT batch file will be created.
       Please check the STARTNET.BAT file contains the right parameters.

     . Content of STARTNET.BAT (for 32-bit LAN driver)

       SET NWLANGUAGE=ENGLISH
       C:\NOVELL\DOSCLNT\NIOS.EXE
       LOAD C:\NOVELL\CLIENT32\LSLC32.NLM
       LOAD C:\NOVELL\CLIENT32\CMSM.NLM
       LOAD C:\NOVELL\CLIENT32\ETHERTSM.NLM
       LOAD C:\NOVELL\CLIENT32\AX88140.LAN FRAME=ETHERNET_802.2 SLOT=??
       LOAD C:\NOVELL\CLIENT32\AX88140.LAN FRAME=ETHERNET_802.3 SLOT=??
       LOAD C:\NOVELL\CLIENT32\AX88140.LAN FRAME=ETHERNET_II    SLOT=??
       LOAD C:\NOVELL\CLIENT32\AX88140.LAN FRAME=ETHERNET_SNAP  SLOT=??
       LOAD C:\NOVELL\CLIENT32\IPX.NLM           <-- Binding driver
       LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM      <-- Finding server


     . Content of STARTNET.BAT (for 16-bit LAN driver)

       SET NWLANGUAGE=ENGLISH
       C:\NOVELL\CLIENT32\NIOS.EXE
       C:\NOVELL\CLIENT32\LSL.COM
       C:\NOVELL\CLIENT32\N16ODI.COM
       C:\NOVELL\CLIENT32\NESL.COM
       C:\NOVELL\CLIENT32\AX88140.COM
       LOAD C:\NOVELL\CLIENT32\LSLC32.NLM
       LOAD C:\NOVELL\CLIENT32\PC32MLID.LAN
       LOAD C:\NOVELL\CLIENT32\TCPIP.NLM
       LOAD C:\NOVELL\CLIENT32\IPX.NLM           <-- Binding driver
       LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM      <-- Finding server


     . Content of NET.CFG

        Link Driver AX88140
                Frame Ethernet_802.2
                Frame Ethernet_802.3
                Frame Ethernet_II
                Frame Ethernet_SNAP

        NetWare DOS Requester
                FIRST NETWORK DRIVE = F
                NETWARE PROTOCOL = NDS BIND



     NOTE: You can run the NetWare client installation program for each
           workstation type from the CLIENT directory under SYS:PUBLIC or
           directly from the CD-ROM.


   Case 2:

   Install Driver After DOS/Windows 3.1x is Installed with Client 32

     . Copy the LAN driver and LDI file to the \Novell\Client32 directory,
       and use text editor to edit STARTNET.BAT file directly.


Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web1, load: 0.73