*****************************************************************************
* *
* PCI Ethernet Adapter *
* *
* NDIS2 Driver for Lan Server DOS Workstations *
* *
* V. 2.91, Jan. 1997 *
* *
*****************************************************************************
Introduction:
=============
The Ethernet NDIS2 Driver for Lan Requester DOS workstations confirms to the
Network Driver Interface Specification(NDIS2). This document shows you how
to setup the driver and how to use the enhanced functions by setting the
custom keywords in configuration file.
Contents of the Subdirectory:
=============================
PCIND.DOS The NDIS2 driver for Lan Requester DOS workstations.
OEMSETUP.INF The installation information file.
LSDOS.TXT This file.
Installation:
=============
Before starting with the installation process, make sure that the adapter
is properly installed and configured. You can use the diagnostic program
(A:\SETUP.EXE) to make sure your connection with the network is correct.
Installing driver procedure on DOS LAN Requester :
-------------------------------------------------
1) Install DOS Lan Requester to HardDisk with "NO Network Adapter
Selected" option.
2) Copy PCIND.DOS from your Driver diskette to DOS LAN Services
subdirectory, like C:\NET .
3) Under DOS LAN Requester subdirectory C:\NET, run INSTALL
4) Move highlight to "The listed options are correct" item ,
then press ENTER.
5) Move highlight to "Network Card", then press ENTER.
6) Select "Change driver for network card." item, then press ENTER.
7) Select "Network card not shown in list below..", then press ENTER.
8) Insert the PCI Ethernet driver diskette in floppy A,and specify
the pathname A:\LANSVR40.DOS,then press ENTER.
9) PCI Ethernet NDIS2 driver is now installed on your computer, reboot
your computer.
NOTE:
-----
Multiple Lan Adapters in a system:
If you want to install mutiple Lan adapter in your system, you have to use
the keyword, PCIID, in PROTOCOL.INI file to let driver locate the right
adapter. And you must set DriverName to be PCIND$ and PCIND2$ for two
different adapters.
You can run A:\SETUP.EXE under DOS prompt to show all the
Ethernet addresses of your adapters.
Configuration Files:
====================
Sample of configuration file:
-----------------------------
(Suppose the Lan Requester package is installed at C:\NET directory)
File Name: C:\CONFIG.SYS
----------
DEVICE=C:\NET\PROTMAN.DOS /I:C:\NET
DEVICE=C:\NET\DLSHELP.SYS
DEVICE=C:\NET\PCIND.DOS
File Name: C:\AUTOEXEC.BAT
----------
SHARE
C:\NET\NET START
C:\NET\NET START PEER
C:\NET\NET SHARE ZZZ=C:\
File Name: C:\NET\PROTOCOL.INI
----------
...
# The followings are Custom Keywords. Put the keywords to enable the
# special functions.
[MS$PCIND]
DriverName=PCIND$
IOBASE=0x300
INTERRUPT=5
EARLYRECEIVE=0
EARLYTRANSMIT=0
FULLDUPLEX=0
[MS$PCIND]
DriverName=PCIND2$
IOBASE=0x320
INTERRUPT=9
EARLYRECEIVE=0
EARLYTRANSMIT=0
FULLDUPLEX=0
[IBM$NETBEUI]
DriverName=netbeui$
SESSIONS=20
NCBS=20
BINDINGS=MS$PCIND
LANABASE=0
...
Custom Keywords:
----------------
PCIID="hhhhhhhhhhhh" This keyword is the Ethernet Address of
the adapter you want to drive. If there
are more than one ethernet adapters in
your system, you have to use this
keyword to let driver locate the right
adapter. However, you don't have to use
this property or let the value to be
zero (i.e. PCIID=0) if there is only
one adapter in your system.
Note: Please remember to enter the
double quotes.
EARLYTRANSMIT This keyword is used to enable turbo
transmission mode for accelerating data
transmission.
EARLYRECEIVE This keyword is used to enable turbo
transmission mode for accelerating data
receiption.
FULLDUPLEX This keyword is used to enable full
duplex mode.
Note: For PCI mode adapter, the IOBASE and INTERRUPT keywords values
are ignored in your PROTOCOL.INI file.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.