10/100 MB Ethernet Adapter Installation
NetWare Client 32 for DOS/Windows 3.1x/Windows 95
Contents
ÄÄÄÄÄÄÄÄ
Introduction
Requirements
Minimum Skill Level
Compatibility List
Getting Started
Introduction
ÄÄÄÄÄÄÄÄÄÄÄÄ
NetWare Client 32 for Windows 95 does not come bundled with the necessary
driver for proper install of this PCI Ethernet Adapter. It is important
that you go through the stated procedure to install the correct device
driver for the adapter to function correctly.
Requirements
ÄÄÄÄÄÄÄÄÄÄÄÄ
A PCI compatible computer
Microsoft Windows 95
Microsoft Windows
Novell NetWare Client 32
A 10/100 MB Ethernet PCI Ethernet Adapter
knowledge of basic Windows 95 commands and editing text files
Minimum Skill Level
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
knowledge of basic Windows 95 commands
knowledge of editing text files
knowledge of Windows 95 basic file structure
knowledge of the network driver configuration being used
Compatibility List
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Any PCI Family Ethernet Adapter
For a Motherboard compatibility list please consult your local
Branch Office
Getting Started
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Client 32 for Windows 95
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Method 1:
Installing a new Auto Detect Network Card on WIN95 WITHOUT Client 32
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
If you have previously installed Novell Netware Client 32 under
your Windows 95 system, skip this section and see
"Method 2" below.
Client 32 Diskette Installation:
. Copy(Override) the NWDLKPCI.INF file to Disk 1 (setup) of the Client 32
for Windows 95 software.
. Copy the new DLKPCI.LAN driver to the Client 32 LAN driver
diskette (32-bit).
. Add a new reference line into the "INF Files" section of
the NWSETUP.INI file.
Note: NWSETUP.INI can be found on Disk 1, or in the \NOVELL\CLIENT32\
INSTALL directory after installation.
Sample of NWSETUP.INI file:
.
.
.
[INF Files]
1=NWClient.inf
2=NWTrans.inf
3=ODINSUP.inf
4=NE3200.inf <--- replace the line to 4=NWDLKPCI.inf
5=NE2000.inf
6=NE15_21.inf
7=NE2.inf
8=NE2_32.inf
.
.
Shut down the system, remove the older card, add the new card, turn
on the system.
Remove adapters from the Network control panel for any cards that
are no longer in the system or are going to be removed.
In "System Settings Change" window, select "No".
Continue to install NetWare Client 32.
Run the Client 32 install using SETUP.EXE, check the box to replace
NDIS with ODI.
(The WIN95 CD will probably be required)
In "Select Device" windows, select "DEC DC21x4" for Manufacturers,
and select proper model for your PCI LAN adapter.
After installation completed, reboot the machine.
Watch WIN95 auto-detect the hardware. The correct new ODI driver
should be installed.
Method 2:
Installing a new Auto Detect Network Card on WIN95 WITH Client 32
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
In Windows 95, go to the \Windows\INF\ directory.
Remove the old NWDLKPCI.INF file (if it exists).
Create a temporary directory and copy all the files from the
\Windows\INF\ directory to this temporary directory.
Verify that the copy completed properly and the two directories
contain the same files.
Delete all the files (*.INF) in the \Windows\INF\ directory.
Copy the new NWDLKPCI.INF into \Windows\INF\ directory.
Now copy all the files back from the temporary directory you created
to the \Windows\INF\ directory.
NWDLKPCI.INF should now be the first one Windows sees in the loading
process, and be loaded before any others for the same adapter.
Remove any adapter from the Network Control Panel for any cards that
are no longer in the system or are going to be removed, including
ODINSUP and any asscoiated files.
Shut down the system, remove the old card, install the new card,
and turn on the system.
Watch WIN95 auto-detect the hardware, and select correct new ODI
driver to be installed. If not, you may select the "Have Disk"
option for installation, in which case you will be prompted to
input the path where the driver located:
ex. A:\CLIENT32.95, if floppy disk is used.
C:\CLIENT32.95, if hard disk is used.
You will then be prompted for Client 32 diskettes.
Complete the Client 32 installation.
Client 32 for DOS/Windows 3.1x
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Method 1: Install Driver During Install
Novell NetWare Client 32 for DOS/Windows 3.1x
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
In DOS environment, run "INSTALL" command.
Follow the installation steps of Novell NetWare Client 32.
In "Select a LAN Driver Type" window, select "32-bit" LAN drivers.
In "32-Bit Network Board Drivers" window, select
"USER SPECIFIED 32 BIT DRIVER".
In "Insert The Driver Disk" window, input the path
where the LAN driver and .LDI file locate:
ex. A:\CLIENT32, if floppy disk is used.
C:\CLIENT32, if hard disk is used.
Select the desired parameters, eg. SLOT number....
and continue the installation procedure.
In MS Windows environment, run "SETUP" command.
In "ODI Driver Selection" window, select "32 bit" mode
and "other Boards".
Enter the path and filename of the ODI driver in "ODI Driver Path"
window.
Follow the installation setps of Novell NetWare Client 32.
After the installation, a STARTNET.BAT batch file will be created.
Please check the STARTNET.BAT file contains the right parameters.
Content of STARTNET.BAT (for 32-bit LAN driver)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
SET NWLANGUAGE=ENGLISH
C:\NOVELL\DOSCLNT\NIOS.EXE
LOAD C:\NOVELL\CLIENT32\LSLC32.NLM
LOAD C:\NOVELL\CLIENT32\CMSM.NLM
LOAD C:\NOVELL\CLIENT32\ETHERTSM.NLM
LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_802.2 SLOT=??
LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_802.3 SLOT=??
LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_II SLOT=??
LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_SNAP SLOT=??
LOAD C:\NOVELL\CLIENT32\IPX.NLM <-- Binding driver
LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM <-- Finding server
Content of STARTNET.BAT (for 16-bit LAN driver)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
SET NWLANGUAGE=ENGLISH
C:\NOVELL\CLIENT32\NIOS.EXE
C:\NOVELL\CLIENT32\LSL.COM
C:\NOVELL\CLIENT32\N16ODI.COM
C:\NOVELL\CLIENT32\NESL.COM
C:\NOVELL\CLIENT32\DLKPCI.COM
LOAD C:\NOVELL\CLIENT32\LSLC32.NLM
LOAD C:\NOVELL\CLIENT32\PC32MLID.LAN
LOAD C:\NOVELL\CLIENT32\TCPIP.NLM
LOAD C:\NOVELL\CLIENT32\IPX.NLM <-- Binding driver
LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM <-- Finding server
Content of NET.CFG
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Link Driver DLKPCI
Frame Ethernet_802.2
Frame Ethernet_802.3
Frame Ethernet_II
Frame Ethernet_SNAP
NetWare DOS Requester
FIRST NETWORK DRIVE = F
NETWARE PROTOCOL = NDS BIND
NOTE: You can run the NetWare client installation program for each
workstation type from the CLIENT directory under SYS:PUBLIC or
directly from the CD-ROM.
Method 2: Install Driver After Novell NetWare Client 32 for
DOS/Windows 3.1x is Installed
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Copy the LAN driver and LDI file to the \Novell\Client32 directory,
and use text editor to edit STARTNET.BAT file directly.
TroubleShooting
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
If you experience the warning messages displayed when STARTNET.BAT
is executed, "Command Line Parameter Prompt for DLKPCI" then follow
the instructions as below:
Change
LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_802.3
to
LOAD C:\NOVELL\CLIENT32\DLKPCI.LAN FRAME=ETHERNET_802.3 SLOT=1
in STARTNET.BAT, where SLOT must be the correct value as found
by driver.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.