CIRRUS.TXT Driver File Contents (1414PCV.exe)

______________________________________________________________________________
Table of Contents - Cirrus Logic Chip Set

 1**Extended AT Command Set
 2**V.42/V.42 bis MNP AT Commands
 3**Fax Class 1 AT Commands
 4**IS-101 Voice AT Commands
 5**AT Command Result Codes
 6**S-Registers
_____________________________________________________________________________
1**Extended AT Command Set**

Data Transmission Commands
AT Commands
A/ **   Re-execute previous command.
A       Answer
Bn *    Select ITU-T or Bell
	B0      Selects ITU-T V.22 at 1200bps and Bell 103J at 300bps
	B1      Selects Bell 212A at 1200bps and Bell 103J at 300bps (default)
	B2      Selects ITU-T V.23 only. The originating modem transmits at  
		75 bps (and receives at 1200 bps); the answering modem   
		receives at 75 bps (and transmits at 1200 bps)
	B3      Selects ITU-T V.23 only. The originating modem transmits at
		1200 bps (and receives at 75 bps); the answering modem
		receives at 1200 bps (and transmits at 75 bps)  

Cn      Carrier control Option.
	C0      Transmit carrier always off 
	C1      Normal transmit carrier (default)

D       Dial command
	P       Select pulse dialing; affects current and subsequent dialing.
	T       Select tone dialing; affects current and subsequent dialing.

En *    Command echo
	E0      Disables echo. 
	E1      Enables echo (default). 

Fn      On-Line Echo Command 
	F0      Enables online echo
	F1      Disables online echo (default)

Hn      Switch hook Control
	H0      (Default) Hangs up the telephone line.
	H1      Picks up the telephone line

In      Indentification/checksum option
	I0      Reports product code   (default)
	I1      Reports modem chip firmware version
	I2      Verifies ROM checksum
	I3      Reports chipset name
	I4      Reserved
	I5      Reserved for modem chip hardware configuration
	I6      Country code
	I7      Version of board manufacturer firmware
	I8      Features of modem firmware
	I10     Modem board configuration-bits set by board manufacturer
	I11     Modem board configuration-bits set by board manufacturer
	I14     SAFE device
	I20     Cirrus Logic silicon version
	I21     Cirrus Logic firmware version
	I22     Cirrus Logic manufacturer name
	I23     Cirrus Logic product model


Ln *    Speaker volume
	L0      Off or Low speaker volume
	L1      Low volume.
	L2      Medium volume (default)
	L3      High volume.

Mn *    Speaker control
	M0      Speaker is always off.
	M1      Speaker is on until carrier present  (default)
	M2      Speaker is always on.
	M3      Speaker is off during dialing; speaker on until until carrier
		present

Nn *    Select data rate handshake
	N0      Handshake only at DTE-to-modem data rate
	N1      Begins handshake at DTE-to-modem data rate and falls to  
		highest compatible rate (default)

On      Go online 
	O0      Returns modem to data mode (default)
	O1      Retrains equalizer and then returns to data mode

P *     Select pulse dialing 


Qn *    Result code display control
	Q0      Enables result codes (default)
	Q1      Disables result codes 

Sn      Select an S-register.  n=0-37

Sn=x    Write to an S-register. n=0-37 x=0-255

Sn?     Reads from an S-register. n=0-37

T *     Selects Tone Dialing

Vn *    Result code form
	V0      Choose numeric form
	V1      Chose verbose (text) form (default)

Wn *    Response code data rate
	W0      Reports DTE speed response codes (default)
	W1      Reports DTE speed response codes
	W2      Reports DCE speed response codes
	W3      Reports DTE speed response codes and information on error
		correction and data compression
	W4      Reports protocol, data compression, and DTE data rate.

Xn *    Result code type
	X0      Enables result codes 0-4; disables detection of busy and dial
		tone.
	X1      Enables result codes 0-5,10, and above; disables busy and dial
		tone detection.
	X2      Enables result codes 0-6 and 10 and above; disables busy
		detection and enables dial tone detection
	X3      Enables result codes 0-5,7, and 10 and above; enables busy
		detection and disables dial tone detection
	X4      Enables result codes 0-7 and 10 and above; disables busy
		detection and disables dial tone detection (default)

Yn *    Long space disconnect
	Y0      Disables long space disconnect (default)
	Y1      Enables long space disconnect

Zn      Recall stored profile
	Z0      Resets modem and recalls user profile 0 (default)
	Z1      Resets modem and recalls user profile 1.

&Cn *   Data Carrier Detect (DCD) option
	&C0     Ignores remote modem status; DCD always on
	&C1     DCD set according to remote modem status (default)

&Dn     Data Terminal Ready (DTR) option
	&D0     In async mode, DTR is ignored.
	&D1     Modem switches from data mode to command mode when an on-to-
		off transition of DTR occurs.
	&D2     When DTR switches off, the modem goes on-hook and disables
		auto-answer mode; when DTR switches on, auto-answer is 
		enabled (default)
	&D3     Turning off DTR re-initializes the modem and resets values 
		except UART registers

&F      Load factory defaults

&Gn *   Guard tone option
	&G0     Disables guard tone (default).
	&G1     Enables 550-Hz guard tone.
	&G2     Enables 1800-Hz guard tone.

&Jn *   Auxiliary relay control
	&J0     Auxiliary relay never operated (default)
	&J1     Activates auxiliary relay when modem is off-hook

&Kn     Select serial port flow control.
	This command selects the flow control method chip set provides to the
	DTE to prevent the modem's buffer from overflowing with data. A data
	buffer holds the data until the modem is ready to transmit it. When
	the data buffer is full, flow control instructs the DTE to stop
	sending to the modem while the modem continues to send characters.

	&K0     Disables flow control
	&K3     Bidirectional hardware flow control (default). 
	&K4     Enables XON/XOFF software flow control.

&M0 *   Communication mode option-modem supports only async mode

&Pn *   Dial pulse ratio
	&P0     Sets 10-pps pulse dial with 39%/61% make-break (default)
	&P1     Sets 10-pps pulse dial with 33%/67% make-break

&Q0 *   Communication mode option-modem supports only async mode

&Sn *   DSR (Data Set Ready) option
	&S0     DSR is always active (default).
	&S1     DSR active only during handshaking and when carrier is lost

&Tn     Self test commands
	&T0     Terminates test in progress 
	&T1     Initiates local analog loopback
	&T3     Initiates local digital loopback
	&T4     Grants RDL (remote digital loopback) request from remote
		modem
	&T5     Denies RDL request from remote modem
	&T6     Initiates remote digital loopback (RDL)
	&T7     Starts remote digital loopback with self-test 
	&T8     Initiates local analog loopback with self-test

&Un *   Disable Trellis coding
	&U0     Enables Trellis coding with QAM as fallback (default)
	&U1     QAM Modulation only

&Vn     View active and stored profiles
	&V0     View stored profile 0 (default)
	&V1     View stored profile 1
	&V3     View relay and general-purpose input-output status

&Wn     Store active profile
	&W0     Store in user profile 0.
	&W1     Store in user profile 1.

&Yn *   Select stored profile on power up
	&Y0     Recall stored profile 0 on power-up (default)
	&Y1     Recall stored profile 1 on power-up

&Zn=x  Store telephone number (up to 30 digits) to location 'n'
	n = 0-3.
	x = dial string (0-9 A B C D # * T P R W @ , ! ;)

%En *   Auto-retrain control
	%E0     Disables auto-retrain (default)
	%E1     Enables auto-retrain
		
%Gn *   Rate renegotiation
	%G0     Disabled (default).
	%G1     Enabled.

-Cn *   Generate data modem calling tone
	-C0     Calling tone disabled
	-C1     1300-Hz calling tone enabled
	-C2     V.8 calling tone and 1300-Hz calling tone

+GMI?***Identify modem manufacturer
+GMM?***Identify product model
+GMR?***Identify product version
+MS=m***Modulation selections
        m=X2, 1, 300, 0
	See full command description in the CL-MD56XX Programmer's Guide for parameter ranges.
	For data modes, the factory default settting is AT+MS=x2, 1, 300, 0 to send at speed of 
        31,200 or below and receive at speed of 53,333 bps and below 
_____________________________________________________________________________
*   denotes value saved in NVRAM
**  denotes command not preceded by an 'AT'
*** denotes command works only on 56K modem    




_____________________________________________________________________________
2**V.42/V.42 bis MNP AT Commands**

%An *   Set auto-reliable fallback character (default=13)
	n=0-127

%Cn *   MNP 5 data compression control
	%C0  No compression
	%C1  Enables MNP 5 data compression (default)

\An *   MNP block size
	  \A0       Max 64 characters.
	  \A1       Max 128 characters.
	  \A2       Max 192 characters.
	  \A3       Max 256 characters (default).

\Bn *   Transmit break
	n=0-9

\Cn *   Set auto-reliable buffer
	\C0     No data buffering (default)
	\C1     Four second buffer until 200 characters in the buffer or
		detection of a SYN character
	\C2     No buffering. Connects non-V.42 modems to V.42 modem                                     
	
\Gn *   Set modem port flow control
	\G0     Disables modem port flow control (default). 
	\G1     Sets port flow control to XON/XOFF
\Jn *   bps rate adjust control
	\J0     Disables rate adjust (default).
	\J1     Enables rate adjust

\Kn *   Set Break control
	In connect state, transmits break to remote (if in reliable mode)
	\K0, 2, 4  Enters command mode; no break sent
	\K1        Destructive/expedited
	\K3        Nondestructive/expedited
	\K5        Nondestructive/nonexpedited (default).
	In command state, transmits break to remote (if in reliable mode)
	\K0, 1     Destructive/expedited
	\K2, 3     Nondestructive/expedited
	\K4, 5     Nondestructive/nonexpedited
	In connect state, receives break at modem port (if in direct mode)
	\K0, 2, 4  Immediately sends break and enters command state
	\K1, 3, 5  Immediately sends the break through
	In connect state, receives break at modem port & sends to serial port
	\K0, 1     Destructive/expedited
	\K2, 3     Nondestructive/expedited
	\K4, 5     Nondestructive/nonexpedited

\Nn *   Set operating mode
	\N0, 1  Selects Buffer (Normal) mode with speed buffering
	\N2     MNP reliable (error-correction) mode.
	\N3     Selects V.42 auto-reliable mode (default)
	\N4     Selects V.42 reliable mode

\O      Originate reliable link

\Qn *   Set serial port flow control
	\Q0     Disables flow control.
	\Q1     XON/XOFF software flow control.
	\Q2     Unidirectional hardware flow control
	\Q3     Bidirectional hardware flow control (default)

\Tn    Set inactivity timer
	n=0     Disable inactivity timer (default).
	n=1-90  Length in minutes.

\U      Accept reliable link

\Xn *   Set XON/XOFF passthrough option
	\X0     Processes flow control characters (default)
	\X1     Processes flow control characters & passes to local or remote

\Y      Switch to reliable mode 

\Z      Switch to Normal mode

-Jn *   Set V.42 detection phase
	-J0     Disables the V.42 detection phase.
	-J1     Enables the V.42 detection phase (default).

"Hn *   V.42 bis compression control
	"H0     Disables V.42 bis
	"H1     Enables V.42 bis only when transmitting data
	"H2     Enables V.42 bis only when receiving data
	"H3     Enables V.42 bis for both transmitting and receiving data

"On     V.42 bis string length
	n=6-250 (default=32)

_____________________________________________________________________________
*  denotes  value saved in NVRAM



_____________________________________________________________________________
3**Fax Class 1 AT Commands**

+FAE=n          Fax/data autorecognition
		n=0,1 (default=0)
+FCLASS=1       Mode selection. Range=0, 1, 8, 80 (default=0)
+FRH=n          Receive HDLC data. Range=3 (default=none)
+FRM=n          Receive data. Range=24, 48, 72, 73, 74, 96, 97, 98, 121,
		122, 145, 146 (default=none)
+FRS=n          Wait for silence.  Range=1-255 (default=none)
+FTH=n          Transmit HDLC data.  Range=3 (default=none)
+FTM=n          Transmit data. Range=24, 48, 72, 73, 74, 96, 97, 98, 121,
		122, 145, 146 (default=none)
+FTS=n          Stop tranmission and pause.  Range=1-255 (default=none)

Fax Indentity Commands

+FMDL?		Identifies product model
+FMFR?		Identifies modem manufacturer
+FMI?		Identifies modem manufacturer
+FMM?		Identifies product model
+FMR?		Identifies product version number
+FREV?		Identifies product version number



_____________________________________________________________________________
4**IS-101 Voice AT Commands**

Command    Function                             Default         Range
-----------------------------------------------------------------------------
+FCLASS=8  Voice mode selection                 0               0, 1, 8, 80
+FLO=n     Flow Control Select                  1               0-2
+VBT=m     Buffer threshold setting             192,320         192,320
+VCID=n    Caller ID Selection                  *0              0-2
#VCSD=n    Voice command mode silence detection 0               0,1
+VDR=m     Distinctive Ring selection           0,0             0-255,     
								0-255
+VEM=m     Event reporting and masking          'C'             --
						BB860980        
						BFE63883        
						BB863EE0
+VGM=n     Speakerphone microphone gain         128             121-131     
+VGR=n     Receive gain selection               128             121-131
+VGS=n     Speakerphone speaker gain            128             121-131
+VGT=n     Volume selection                     128             121-131
+VIP       Initialize parameter                 --              --
+VIT=n     DTE/DCE inactivity timer             0               0-255
+VLS=n     Relay/speaker control                0               0-16
+VNH=n     Automatic hang-up control            0               0-2
+VRA=n     Ringback-goes-away timer             50              0-50
+VRN=n     Ringback-never-appeared timer        10              0-255
+VRX   *** Record mode                          --              --
+VSD=m *** Silence detection (quiet and silence)128, 50         See note
+VSM=m *** Compression method selection         140, 8000, 0    See note
+VSP=n     Speakerphone on/off control          0               0, 1
#VSPS=n*** Speakerphone type selection          Manufacturer    0, 1
                                                specified
+VTD=n     Beep tone duration timer             100             5-255
+VTS=m *** DTMF and tone generation		none		See note
+VTX   *** Play mode				none		--
_____________________________________________________________________________
*   Noted parameters, commands, and responses depend on the capability to
    receive.
*** denote command for 56K modem

Voice DTE-to-DCE Character Pairs

Response     Hex Code        Function
--------------------------------------------
<NUL>        00              Do nothing
<DLE>        10		     Two contiguous <DLE><DLE> codes indicates a
                             single <DLE> in the data stream
<SUB>        1A		     <DLE><DLE> in data stream
<ETX>	     03		     End transmit data state
/	     2F        	     Start of DTMF tone shielding
~	     7F		     DTMF transition to off
u	     75		     Bump up the volume
d	     64		     Bump down the volume
< ESC>	     1B		     End receive data state
!	     21		     Receive data abort
<CAN>	     18	   	     Clear transmit buffer of voice data
<FS>	     1C		     Concatenate transmit data streams
?	     3F		     Transmit buffer space available query

Voice DCE-to-DTE Character Pairs

Response     Hex Code         Function
--------------------------------------------
<DLE>        10		      Single <DLE> character in the data stream
<SUB>	     1A		      <DLE><DLE> in data stream
<ETX>        3		      End of record mode data
X	     58		      Packet header for 'Complex Event Detection
                              Report'
.	     2E		      Packet terminator for the 'Complex Event
                              Detection Report'
/	     2F		      Start of DTMF tone shielding
~ 	     7E		      DTMF transition to off
0-9	     30-39	      DTMF tones 0-9
A-D	     41-44	      DTMF tones A-D
*	     2A		      DTMF tone *
#	     23  	      DTMF tone #
o	     6F		      Receive buffer overrun
c	     63 	      1100-Hz fax calling tone
e	     65		      1300-Hz data calling tone
h    	     68 	      Local phone goes on hook
H 	     48    	      Local phone goes off hook
s 	     73	       	      Presumed hang-up silence time-out
l  	     6C		      Loop current interruption
L	     4C 	      Loop current polarity reversal
r	     72		      Ringback
b	     62		      Busy/reorder/fast busy
d	     64		      Dial tone detected
u	     75		      Transmit buffer under-run
p 	     70 	      Line voltage increase (extension phone
                              goes on-hook)
p            50		      Line voltage decrease (extension phone
                              goes off-hook)
a	     61		      Fax or data answer tone (2100 Hz)
f	     66		      Data answer detected (2225 Hz)
R 	     52 	      Incoming ring
%' (,)	     25, 26, 27       Manufacturer-specified
	     28,29

V.80 Videoconferencing Mode Commands

Command		Fuction			Default			Range
--------------------------------------------------------------------------------
FCLASS=0	Mode selection		0			0,1, 8, 80
+A8E=M		V.8 & V.8 bis operation 1, 1, C1, 0,  , 	See note 
+ES=m		Error control selection 3, 0, 2			See note
+ESA=m		Synchronous access	0, 0, 1,  , 0, 0, 126	See note
		mode configuration
+ITF=m		Transmit flow control	320, 192, 0		See note
		thresholds
+8-bit in-band	In-band commands and	none			see note 
controls:	indications for use in
<EM><hex code>	asynchronous access mode only

Dial Modifiers

Command			Function
----------------------------------------------------------------------------
0 to 9			Dialing digits
A, B, C, D, *, #	Tone dial characters
P			Pulse dial
R			Reserse originate mode
S=n			Dial NVRAM telephone number
T			Wait for dial tone
,			Pause
!			Flash hook
@			Wait for quiet answer
;     			Return to idle state
-()			Ignored by modem
_____________________________________________________________________________

____________________________________________________________________________
5**AT Command Result Codes**

Numeric   
Code    Verbose Code
---------------------
0       OK       
1       CONNECT
2       RING
3       NO CARRIER
4       ERROR
5       CONNECT 1200
6       NO DIAL TONE
7       BUSY
8       NO ANSWER
23      CONNECT 75/1200
22      CONNECT 1200/75
10      CONNECT 2400
11      CONNECT 4800      
24      CONNECT 7200
12      CONNECT 9600
25      CONNECT 12000
13      CONNECT 14400
59      CONNECT 16800
14      CONNECT 19200
61      CONNECT 21600
62      CONNECT 24000
63      CONNECT 26400
64      CONNECT 28800
65	CONNECT 31200
33      FAX 		(33.6k modem)
	CONNECT 33333	(56K modem)
66	CONNECT 33600 	(56K modem)
34 	CONNECT 37333	(56K modem)
28      CONNECT 38400	(56K modem)
35	CONNECT 41333	(56K modem)
35      DATA
36	CONNECT	42666	(56K modem)
37	CONNECT	44000	(56K modem)
38	CONNECT 45333	(56K modem)
39 	CONNECT 46666	(56K modem)
42	CONNECT 48000	(56K modem)
43	CONNECT 49333  	(56K modem)
53	CONNECT 50666	(56K modem)
54	CONNECT 52000	(56K modem)
55 	CONNECT 53333	(56K modem)
56	CONNECT	54666	(56K modem)
57	CONNECT 56000	(56K modem)
58	CONNECT 57333 	(56K modem)
18      CONNECT 57600
31      CONNECT 115200
45      RINGBACK
____________________________________________________________________________
* Noted parameters, commands, and responses depend on the capability to 
  receive



____________________________________________________________________________
6**S-Registers**

No.     Function                        Range           Units   Default
 *0     Rings to auto-answer on         0-255           ring    0
  1     Ring count                      0-255           ring    0
 *2     Escape character                0-127           ASCII   43
  3     Carriage-return character       0-127           ASCII   13
  4     Line-feed character             0-127           ASCII   10
  5     Backspace character             0-32, 127       ASCII   8
 *6     Wait before dialing             2-255           second  2
 *7     Wait for carrier                1-255           second  60
 *8     Pause time for dial modifier    0-255           second  2
 *9     Carrier recovery time           1-255           0.1 s   6
*10     Lost carrier hang up delay      1-255           0.1 s   14
*11     DTMF dialing speed              50-255          0.001 s 70
*12     Guard time                      0-255           0.02 s  50
*14     Bit-mapped options              _               _       170
 16     Modem test options              _               _       0
*18     Modem test timer                0-255           second  0
*21     Bit-mapped options              _               _       48
*22     Bit-mapped options              _               _       118
*23     Bit-mapped options              _               _       none
*25     Detect DTR change               0-255           0.01 s  5
*27     Bit-mapped options              _               _       64
*30     Disconnect inactivity timer     _               _       0
*31     Bit-mapped options              _               _       none
*33     Sleep mode timer                0-90            second  10
*37     Maximum line speed attempted    0-19            _       0
____________________________________________________________________________
* Value saved in NVRAM





____________________________________________________________________________
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web3, load: 0.94