PS3205U_serial.txt Driver File Contents (PS-3205Uv135.zip)

PS3205U & PS3205UWG & PS1205UWG serial firmware release note

Print server firmware 1.35 2004/01/20
  1.Update wireless driver to fixed wep key mapping issue
  2.Telnet function support write mac if the mac value is reset to default
  3.Disabled dhcp client in default value(General & Edimax only)

Print server firmware 1.34 2004/10/19
  1.Correct the Edimax & General run utility will cause print server agent crash.

Print server firmware 1.33 2004/10/12
  1.Fixed flash default and upplug power core will cause the mac restore to default
  2.Correct the Edimax & General web page error in backup system
  3.When AP's SSID maximize will cause sitesurvey error
  4.Fixed HP 895c will always show paper out
    
Print server firmware 1.32 2004/09/29
  1.Fixed dhcp server can't announce dns & gateway ip
  
Print server firmware 1.31 2004/09/27
  1.Fixed Wep 128bits fail under web ui
  
Print server firmware 1.30 2004/09/22
  1.Fiexd passphrase 128bit key 2,3,4 we follow linksys generate rule.
  
Print server firmware 1.29 2004/09/18
  1.Fixed ipp doesn't work
  2.Update driver to fix appletalk

Print server firmware 1.28 2004/09/14
  1.Fixed can't auto switch lan and wireless.
  2.Lights the led under boot up step.

Print server firmware 1.27 2004/09/10
  1.Add passphrase in web ui.
  2.Add wpa function.
  3.Add backup and restore setting function in web ui.
  4.Update driver to support wpa function

Print server firmware 1.26 2004/08/10
  1.Fixed V1.25 dhcp client fail in wireless mode
  2.Fixed if dhcp client not set enable will cause PStest program fail
  3.Print status led will blink while put reset button to reset default
  4.Assign ip to wireless when unplug lan cable.

Print server firmware 1.25 2004/07/27
  1.Remove passphrase in web ui
  2.Set Dhcp client disable in default value

Print server firmware 1.24 2004/07/26
  1.Set Dhcp client enable in default value.
  2.Add passphrase in web ui
  3.Led on/off after boot code and on/off again in ap code.

Print server firmware 1.23 2004/07/13
  1.Fixed when dhcp server didn't set gateway will cause print server dhcp client fail.
  2.SSID can set empty
  3.Fixed Snmp function fail in realtek platform
  4.Add netbeui function
  5.Fixed appletalk print protocol function
  6.Remove wireless "auto, enable, disable" selection in web UI

Print server firmware 1.22 2004/05/27
  1.Update web UI for hawking request  

Print server firmware 1.21 2004/05/26
  1.Update web UI for hawking request
  2.Fixed gateway function fail.

Print server firmware 1.20 2004/05/13
  1.Fixed webs will be killed when wireless is not connect any AP

Print server firmware 1.19 2004/05/07
  1.Change Hawking default ip to 192.168.1.250 (For Hawking Only)
  2.Change some web page content 
  3.Report telnet, smb, snmp status to UI

Print server firmware 1.18 2004/04/22
  1.Fixed ipx print protocol fail under Netware 4.11

Print server firmware 1.17 2004/04/05
  1.Support snmp and smbd in print server
  2.Add more telnetd command and enable/disable selection in UI & WEBS
  3.Update Inprocomm wireless card driver
  4.Update printer port status report method
    
Print server firmware 1.16 2004/03/4
  1.Fixed the Qname and Psname save error in web page
  2.Light the power led when use wireless

Print server firmware 1.15 2004/02/26
  1.Fixed when upgrade firmware will cause web server crash
  2.Add watch dog , if hang 3 second system will reboot

Print server firmware 1.14 2004/01/28
  1.Fixed when reset to default will cause the print server not running
  2.Speed up the upgrade in tftp, tester program use only
  
Print server firmware 1.13 2004/01/28
  1.Fixed the USB status always show Off-Line!
  2.Change upgrade warning message "Boardband router" to "Print Server"

  
   
 
  
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web2, load: 0.62