NDC ND5300 Plug and Play Ethernet Adapter
ODI Driver for Novell Netware Server (3.11, 3.12, 4.X, 5.00) Installation
=====================================================================
INSTALLATION PROCEDURE
1). Login as SUPERVISOR to your server.
2). Copy all supplied NLM files you find in \NOVELL_S\311, \NOVELL\312,
\NOVELL_S\40 or \NOVELL_S\500 directory (according to your server
version) in "NDC Setup diskette" to your server system directory.
Pay attension that ALL these NLM files are COPYWRITE by Novell.
Please do not distribute these files without permission from Novell.
e.g.
C:\>copy a:\NOVELL_S\311\*.* C:\SERVER
3). Then you have to add one of the loading sequences described in the
AUTOEXEC.NCF template you find in 311, 3.12 or 4.x directory in "NDC
Setup diskette" to your server AUTOEXEC.NCF.
4). Shutdown the server and then restart it again.
p.s. If an error message shows that the ND5300 adapter cannot
be found after loading the ND5300.LAN driver. Try change
the 'PnP OS installed' option to be 'No' in the system
BIOS setup program of your motherboard.
ND5300 Plug and Play Ethernet Adapter
ODI Driver for Novell NetWare DOS Client Installation
=====================================================
The Card comes with a NDCGO program which provide a fast way to
install your PC as a NetWare workstation. It is recommended you run
the NDCGO program for the NetWare DOS client installation.
Otherwise, follow the procedure below to complete the installation.
PRE-INSTALLATION
You should setup and diagnose the Instant-Link adapter(s) by
applying NDCONF3 before you install and/or run the NOS or
network applications.
INSTALLATION PROCEDURE
1) Insert the "NDC Setup diskette" into a floppy drive (A: or B:).
2) Make a directory (usually \NETWARE) on your hard disk (usually
C: drive) to hold the Novell NetWare utilities.
MD C:\NETWARE
3) Copy these files from the "\NOVELL_W" directory of the
"NDC Setup Diskette" to the "\NETWARE" directory of your hard disk:
LSL.COM
ND5300.COM
IPXODI.COM
NETX.EXE
NET.CFG
To copy these files, type:
COPY A:\NOVELL_W\LSL.COM C:\NETWARE
COPY A:\NOVELL_W\ND5300.COM C:\NETWARE
COPY A:\NOVELL_W\IPXODI.COM C:\NETWARE
COPY A:\NOVELL_W\NETX.COM C:\NETWARE
COPY A:\NOVELL_W\NET.CFG C:\NETWARE
(You may use your versions of these programs from Novell
instead)
4) Check with your network administrator to make sure that the
protocol stack (IPX protocol bound with Ethernet Frame type)
defined in the NET.CFG file matches your network. The default
protocol stack is:
PROTOCOL ETHERNET_802.3
If you are running NetWare 3.12, 4.X or 5.00, you may have to
change the frame type to:
PROTOCOL ETHERNET_802.2
5) Make sure the MAM (Media Access Module) is physically
connected to the network. From the "\NETWARE" directory of
your hard disk, you may load the network drivers by typing:
LSL
ND5300
IPXODI
NETX
If you are running NetWare 3.12 4.X or 5.00, you should change the
last line from "NETX" to "VLM". (Note: You may have to install
the VLM files by applying the "NetWare Client for DOS"
diskettes.)
NDC ND5300 Plug and Play Ethernet Adapter
ODI Driver for Novell Netware OS/2 Client (3.11, 3.12, 4.X, 5.00) Installation
=====================================================================
Location of Driver: \NOVELL_W.OS2\ND5300.SYS
Sample Configuration Files:
---------------------------
CONFIG.SYS :
DEVICE=C:\NETWARE\LSL.SYS ; OS/2 Requester supported
DEVICE=C:\NETWARE\DDAEMON.SYS ; OS/2 Requester supported
DEVICE=C:\NETWARE\ND5300.SYS ; NDC supported
DEVICE=C:\NETWARE\IPX.SYS ; OS/2 Requester supported
NET.CFG :
LINK DRIVER ND5300
FRAME ETHERNET_802.3
FRAME ETHERNET_802.2
INSTALLATION PROCEDURE
1) Copy the ND5300.SYS file into the NETWARE subdirectory of your
hard disk from the "ND5300 Driver Diskette" A:\NOVELL_W.OS2.
2) Add or replace the ND5300.SYS in the CONFIG.SYS file.
3) Edit the NET.CFG file that you copied over. Edit the file per your
requirements (see examples above). If there are two frame types
listed, whichever frame type is listed first, that is the one that
the driver will load. See above for examples.
4) Reboot your system to get service of network.
NOTE:
-----
You can bind several frame types to the IPX protocol to support
various configurations. Include this in the Link Driver ND5300
section of the NET.CFG file. A sample is shown below:
Link Driver ND5300
frame Ethernet_802.3
frame Ethernet_802.2
frame Ethernet_II
frame Ethernet_snap
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.