NDC ND5300 Plug and Play Ethernet Adapter
NDIS Driver for FTP PC/TCP for (DOS) Installation
=================================================
PRE-INSTALLATION
You should setup and diagnose the Instant-Link adapter(s) by
applying NDCONF3 before you install and/or run the NOS or
network applications.
INSTALLATION PROCEDURE
1) Insert the "NDC Setup diskette" into drive A: and copy ND5300
NDIS driver to the destination subdirectory of your PC (the
recommended Destination Subdirectory is C:\PCTCP).
A:\> Copy A:\NDIS2\ND5300.DOS C:\PCTCP
2) Refer to Chapter 5 of the PC/TCP Installation and
Configuration Guide, entitled "Using an NDIS Driver with the
Generic Kernel".
3) Copy the netbind files from the \NDIS2 subdirectory on FTP Disk
A, labeled "Unsupported Network Software".
4) Using any text editor, add the following lines to your
workstation's CONFIG.SYS file:
DEVICE=C:\PCTCP\PROTMAN.SYS /I:C:\PCTCP
DEVICE=C:\PCTCP\ND5300.DOS
DEVICE=C:\PCTCP\DIS_PKT.GRP
Adjust the drive and path specifications to match your
installation.
5) Use any text editor to make the PROTOCOL.FTP file in the
\PCTCP subdirectory on your PC's hard drive look as
follows:
[Protocol Manager]:
Drivername = protman$
[PKTDRV]
Drivername = pktdrv$
Bindings = ND5300_NIF
Intvec = 0x60
Chainvec = 0x65
[ND5300_NIF]
DriverName = ND5300$
6) Rename the PROTOCOL.FTP file as PROTOCOL.INI. Refer to your
DOS manual if you need assistance.
7) Proceed with the rest of the instructions in the PC/TCP
Installation and Configuration Guide.
NDC ND5300 Plug and Play Ethernet Adapter
Packet Driver for FTP PC/TCP for (DOS) Installation
===================================================
INSTALLATION PROCEDURE
1) Insert PC/TCP Netware Software for DOS "Disk 1" into drive
A: or B: .
2) Go to drive A: or B: and type: "INSTALL" and press <Enter>.
3). When you are installing the PC/TCP generic kernel, the
Operating Environment menu lists 12 environments. Please
select an IEEE 802.3 packet driver, answer "Y" in the "Pkt Drv"
field. When you have selected the type of driver appropriate
to network configuration, press <F10> and continue the installation.
4) Edit the AUTOEXEC.FTP.
- Replace:
echo Run packet driver here.
with:
ND5300PK 0x60
ETHDRV
where the packet driver (ND5300PK.COM) will use
software interrupt vector 0x60 for ND5300 adapter.
Note: Packet Driver Basic Syntax:
ND5300PK <packet_int_no>
where:
<packet_int_no> This specifies the software interrupt (IRQ)
where you'll load the packet driver. It must
be in the range 0x60 to 0x80.
The PC/TCP kernel, by default, is loaded at
interrupt 0x61 (so don't load the packet
driver there!)
5) Copy ETHDRV.EXE file from "PC/TCP Network Software for DOS
disk 2" to your PC/TCP directory (usually C:\PCTCP).
6) Insert the "NDC Setup diskette" to drive A: and copy ND5300 Packet
driver to the destination subdirectory on your PC (the recommended
Destination Subdirectory is C:\PCTCP).
A:\> Copy A:\PKTDRV\ND5300PK.COM C:\PCTCP
7) To preserve your current AUTOEXEC.BAT file, rename it to
AUTOEXEC.OLD.
REN C:\AUTOEXEC.BAT C:\AUTOEXEC.OLD
Copy AUTOEXEC.FTP to AUTOEXEC.BAT
COPY C:\AUTOEXEC.FTP C:\AUTOEXEC.BAT
This completes the installation of FTP PC/TCP.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.