Flash instructions for Fusion-MPT 2x320-R HBA.txt Driver File Contents (Fusion-MPT_IS_FW10327_BIOS_51101_FLASH_10304.zip)


1. This firmware is intended for use on LSI2x320-R Host Bus Adapters 
which have Integrated RAID capability. Choose either Integrated 
Mirroring Enhanced (IME) or Integrated Striping (IS). 
Check your card model Number by looking at the Host Bus Adapter (HBA).  
If your HBA model number ends with -R, you can safely use this 

2. Do not flash LSI2x320 (non-R) HBA's with this striping or 
mirroring firmware as it will not add the integrated functionality 
to your card, and may harm your HBA.  Instead, use Initiator/Target 
(IT) BIOS and Firmware for LSI2x320 (non-R) HBA. 

3. LSI2x320-IS cards should not use this firmware.  These HBA's are 
manufactured specifically for third party vendors and require vendor 
specific firmware; contact your vendor for appropriate firmare for 
these cards.

The steps to flash an LSI2x320-R HBA are:

1. Download the current Integrated Mirroring (IME) or Integrated 
Striping (IS) version of Fusion-MPT BIOS and firmware. Using Winzip 
or other compatible software extract the files onto a blank floppy 

2. Create a DOS bootable diskette. This can be a basic DOS boot disk 
without a config.sys or autoexec.bat, or if you have a Windows 98 Boot 
disk, you can boot useing this boot diskette and bypass the config.sys 
and autoexec.bat files by holding down the left shift key during boot.

Refer to your Operating System documentation for specific instructions 
on creating a DOS compatible boot diskette.
Boot disk images are also available from www.bootdisk.com 
(not affiliated with LSI Logic).

3. Reboot the system, and boot from the bootable floppy.  
At the A:\ prompt, remove the boot diskette and insert the diskette 
with the extracted LSI Logic rom and firmware image files.

4. At the A:> prompt, type 

'flsh1030 /b:mptpsime.rom' For Integrated mirroring. 
'flsh1030 /b:mptpsis.rom' For Integrated Striping.

Press enter.  The flash utility will flash the HBA's BIOS.

5. At the A:> prompt, type 

'flsh1030 /f:ie_1030.fw' For IME (mirroring) firmware 
'flsh1030 /f:is_1030.fw' For IS (striping) firmware 

Press enter.  The flash utility will flash the HBA's firmware.

For the LSI53C1030T or 53C1020A use either ie_1030T.fw or is_1030T.fw.

*** The flsh1030 executable file can flash both BIOS and fw concurrently
by putting both switches on the command line. 
'flsh1030 /b:mptpsime.rom /f:ie_1030.fw'
'flsh1030 /b:mptpsis.rom /f:is_1030.fw'
Learn more about the flash utility in the Flash 1030.txt file in 
this zip package.

***LSI Logic recommends backing up the current version of BIOS and 
Firmware to file before updating the HBA. The diskette created with the 
new image files should have adequate space for these files.

*** The BIOS .rom image and the Firmware .fw image names may change from 
the examples given in steps 4 and 5 above. Before starting the flash 
utility make a note of the file names for both images.

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web5, load: 0.79