; OEMSETUP FILE FOR Intel 2104x/2114x 10/100 mbps Ethernet Controller , v5.00
; NDIS 4.0 - Windows NT 4.0 -
;
; Supported adapters:
; Intel 21040 based Ethernet Controller
; Intel 21041 based Ethernet Controller
; Intel 21140 based 10/100 mpbs Ethernet Controller
; Intel 21142 based 10/100 mbps Ethernet Controller
; Intel 21143 based 10/100 mbps Ethernet Controller
; Intel EB40 21040 based Evaluation board
; Intel EB41 21041 based Evaluation board
; Intel EB140 21140 based 10/100 mpbs Evaluation board
; Intel EB142 21142 based 10/100 mpbs Evaluation board
; Intel EB143 21143 based 10/100 mpbs Evaluation board
; DEC multia's Ethernet Controller
; DEC DE434 PCI Ethernet Adapter
; DEC DE435 PCI Ethernet Adapter
; DEC DE450 PCI Ethernet Adapter
; DEC DE500 PCI Fast Ethernet Adapter
; DEC DE425 EISA Ethernet Adapter
;
; Intel Corporation 1998
;
; Usage:
;
; This file is the installation/configuration/deinstallation
; procedure of the Intel DC21x4 driver for Windows NT. It can be called
; from Windows Setup directly, or via the Windows NT Networks
; Control Program Applet (NCPA) from inside the Windows
; Control Panel.
;
;----------------------------------------------------------------------------------------
[Identification]
OptionType = NetAdapter
[PlatformsSupported]
ISA
EISA
"Jazz-Internal Bus"
PCI
[Options]
DC21040
DC21041
DC21140
DC21142
DC21143
EB40
EB41
EB140
EB142
EB143
MULTIA
DE434
DE435
DE450
DE500
DE425
[ConnectionChoicesDC21040]
Connect_0 = "AutoDetect", 0
Connect_1 = "10BaseT (TP) ", 2
Connect_2 = "10BaseT (TP) Full Duplex ", 3
Connect_3 = "10BaseT (TP) No_Link_Test", 4
Connect_4 = "10Base2 (BNC)", 1
Connect_5 = "10Base5 (AUI)", 5
[ConnectionChoicesDC21041]
Connect_0 = "AutoSense", 0
Connect_1 = "10BaseT (TP) ", 2
Connect_2 = "10BaseT (TP) Full Duplex ", 3
Connect_3 = "10BaseT (TP) No_Link_Test", 4
Connect_4 = "10Base2 (BNC)", 1
Connect_5 = "10Base5 (AUI)", 5
[ConnectionChoicesDC21140]
Connect_0 = "AutoSense", 0
Connect_1 = "10BaseT (TP) ", 2
Connect_2 = "10BaseT (TP) Full Duplex ", 3
Connect_3 = "100BaseTx (TP 100)", 8
Connect_4 = "100BaseTx (TP 100) Full Duplex", 9
Connect_5 = "100BaseT4", 10
Connect_6 = "100BaseFx", 11
Connect_7 = "100BaseFx Full_Duplex", 12
[ConnectionChoicesDC21142]
Connect_0 = "AutoSense", 0
Connect_1 = "10BaseT (TP) ", 2
Connect_2 = "10BaseT (TP) Full Duplex ", 3
Connect_3 = "10BaseT (TP) No_Link_Test", 4
Connect_4 = "10Base2 (BNC)", 1
Connect_5 = "10Base5 (AUI)", 5
Connect_6 = "100BaseTx (TP 100)", 8
Connect_7 = "100BaseTx (TP 100) Full Duplex", 9
Connect_8 = "100BaseT4", 10
Connect_9 = "100BaseFx", 11
Connect_10 = "100BaseFx Full_Duplex", 12
[ConnectionChoicesDC21143]
Connect_0 = "AutoSense", 0
Connect_1 = "10BaseT (TP) ", 2
Connect_2 = "10BaseT (TP) Full Duplex ", 3
Connect_3 = "10BaseT (TP) No_Link_Test", 4
Connect_4 = "10Base2 (BNC)", 1
Connect_5 = "10Base5 (AUI)", 5
Connect_6 = "100BaseTx (TP 100)", 8
Connect_7 = "100BaseTx (TP 100) Full Duplex", 9
Connect_8 = "100BaseT4", 10
Connect_9 = "100BaseFx", 11
Connect_10 = "100BaseFx Full_Duplex", 12
[ConnectionChoicesEB40]
Connect_0 = "10BaseT (TP) ", 2
Connect_1 = "10BaseT (TP) Full Duplex ", 3
Connect_2 = "10BaseT (TP) No_Link_Test", 4
[ConnectionChoicesEB41]
Connect_0 = "AutoSense", 0
Connect_1 = "10BaseT (TP) ", 2
Connect_2 = "10BaseT (TP) Full_Duplex ", 3
Connect_3 = "10BaseT (TP) No_Link_Test", 4
Connect_4 = "10Base2 (BNC)", 1
Connect_5 = "10Base5 (AUI)", 5
[ConnectionChoicesEB140]
Connect_0 = "AutoSense", 0
Connect_1 = "10BaseT (TP) ", 2
Connect_2 = "10BaseT (TP) Full Duplex ", 3
Connect_3 = "100BaseTx (TP 100)", 8
Connect_4 = "100BaseTx (TP 100) Full Duplex", 9
[ConnectionChoicesEB142]
Connect_0 = "AutoSense", 0
Connect_1 = "10BaseT (TP) ", 2
Connect_2 = "10BaseT (TP) Full Duplex ", 3
Connect_3 = "10BaseT (TP) No_Link_Test", 4
Connect_4 = "10Base2 (BNC)", 1
Connect_6 = "100BaseTx (TP 100)", 8
Connect_7 = "100BaseTx (TP 100) Full Duplex", 9
Connect_8 = "100BaseT4", 10
Connect_9 = "100BaseFx", 11
Connect_10 = "100BaseFx Full_Duplex", 12
[ConnectionChoicesEB143]
Connect_0 = "AutoSense", 0
Connect_1 = "10BaseT (TP) ", 2
Connect_2 = "10BaseT (TP) Full Duplex ", 3
Connect_3 = "10BaseT (TP) No_Link_Test", 4
Connect_4 = "10Base2 (BNC)", 1
Connect_6 = "100BaseTx (TP 100)", 8
Connect_7 = "100BaseTx (TP 100) Full Duplex", 9
Connect_8 = "100BaseT4", 10
Connect_9 = "100BaseFx", 11
Connect_10 = "100BaseFx Full_Duplex", 12
[ConnectionChoicesMULTIA]
Connect_0 = "AutoDetect", 0
Connect_1 = "10BaseT (Twisted_Pair) ", 2
Connect_2 = "10BaseT Full_Duplex ", 3
Connect_3 = "10BaseT No_Link_Test", 4
Connect_4 = "10Base2 (BNC)", 1
Connect_5 = "10Base5 (AUI)", 5
[ConnectionChoicesDE434]
Connect_0 = "10BaseT (Twisted_Pair) ", 2
Connect_1 = "10BaseT Full_Duplex ", 3
Connect_2 = "10BaseT No_Link_Test", 4
[ConnectionChoicesDE435]
Connect_0 = "AutoDetect", 0
Connect_1 = "10BaseT (Twisted_Pair) ", 2
Connect_2 = "10BaseT Full_Duplex ", 3
Connect_3 = "10BaseT No_Link_Test", 4
Connect_4 = "10Base2 (BNC)", 1
Connect_5 = "10Base5 (AUI)", 5
[ConnectionChoicesDE450]
Connect_0 = "AutoSense", 0
Connect_2 = "10BaseT (Twisted_Pair) ", 2
Connect_3 = "10BaseT Full_Duplex ", 3
Connect_4 = "10BaseT No_Link_Test", 4
Connect_5 = "10Base2 (BNC)", 1
Connect_6 = "10Base5 (AUI)", 5
[ConnectionChoicesDE500]
Connect_0 = "AutoSense", 0
Connect_1 = "100BaseTx", 8
Connect_2 = "100BaseTx Full_Duplex", 9
Connect_3 = "10BaseT", 2
Connect_4 = "10BaseT Full_Duplex", 3
[FileConstants]
UtilityInf = "UTILITY.INF"
subroutineinf = "SUBROUTN.INF"
SoftwareType = "driver"
Exit_Code = 0
NetEventDLL = "%SystemRoot%\System32\netevent.dll"
IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll"
Manufacturer = "Intel"
ProductMajorVersion = "5"
ProductMinorVersion = "00"
ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion)
VendorID = 4113 ;; 1011 (DEC)
;;for systemsoft cardwizard
PCMCIADBKeyName = $(!NTN_ServiceBase)"\Pcmcia\DataBase"
PCMCIARMKeyName = $(!NTN_ServiceBase)"\resman\MacDataBase"
PCMCIARMPKeyName = $(!NTN_ServiceBase)"\resman"
DC21X4Manufacture = "Intel"
DC21X4Model = "EB143CS - CardBus evaluation board"
ProductSoftwareName = "DC21X4"
ProductSoftwareTitle = "Intel DC21X4 Adapter Driver"
ProductSoftwareImagePath = "\SystemRoot\System32\drivers\DC21X4.sys"
NetRuleSoftwareType = "DC21X4Sys ndisDriver DC21X4Driver"
NetRuleSoftwareUse = $(SoftwareType)
NetRuleSoftwareBindForm = """DC21X4Sys"" yes no container"
NetRuleSoftwareClass = {"DC21X4Driver basic"}
NetRuleSoftwareSWBindable = {"DC21X4Driver DC21040Adapter non exclusive 100",+
"DC21X4Driver DC21041Adapter non exclusive 100",+
"DC21X4Driver DC21140Adapter non exclusive 100",+
"DC21X4Driver DC21142Adapter non exclusive 100",+
"DC21X4Driver DC21143Adapter non exclusive 100",+
"DC21X4Driver EB40Adapter non exclusive 100",+
"DC21X4Driver EB41Adapter non exclusive 100",+
"DC21X4Driver EB140Adapter non exclusive 100",+
"DC21X4Driver EB142Adapter non exclusive 100",+
"DC21X4Driver EB143Adapter non exclusive 100",+
"DC21X4Driver MULTIAAdapter non exclusive 100",+
"DC21X4Driver DE434Adapter non exclusive 100",+
"DC21X4Driver DE435Adapter non exclusive 100",+
"DC21X4Driver DE500Adapter non exclusive 100",+
"DC21X4Driver DE450Adapter non exclusive 100",+
"DC21X4Driver DE425Adapter non exclusive 100"}
OptionHelpFile = "DC21X4.hlp"
ProductHardwareName = "DC21X4"
ProductHardwareDC21040Title = "Intel 21040 based Ethernet Controller"
NetRuleHardwareDC21040Type = "DC21040 DC21040Adapter"
NetRuleHardwareDC21040Class = {"DC21040Adapter basic"}
AdapterDC21040Type = 5 ;; PCI board
HelpDC21040Id = 10
DC21040CFID = 135185 ;; 0x00021011
ProductHardwareDC21041Title = "Intel 21041 based Ethernet Controller"
NetRuleHardwareDC21041Type = "DC21041 DC21041Adapter"
NetRuleHardwareDC21041Class = {"DC21041Adapter basic"}
AdapterDC21041Type = 5 ;; PCI board
HelpDC21041Id = 20
DC21041CFID = 1314833 ;; 0x00141011
ProductHardwareDC21140Title = "Intel 21140 based 10/100 mpbs Ethernet Controller"
NetRuleHardwareDC21140Type = "DC21140 DC21140Adapter"
NetRuleHardwareDC21140Class = {"DC21140Adapter basic"}
AdapterDC21140Type = 5 ;; PCI board
HelpDC21140Id = 30
DC21140CFID = 593937 ;; 0x00091011
StoreAndForward = 0 ;; Store_and_forward mode disabled
TxmThreshold100 = 512 ;; 100Mbps default threshold
ProductHardwareDC21142Title = "Intel 21142 based 10/100 mpbs Ethernet Controller"
NetRuleHardwareDC21142Type = "DC21142 DC21142Adapter"
NetRuleHardwareDC21142Class = {"DC21142Adapter basic"}
AdapterDC21142Type = 5 ;; PCI board
HelpDC21142Id = 40
DC21142CFID = 1642513 ;; 0x00191011
ProductHardwareDC21143Title = "GFC2202 10/100 PCI Fast Ethernet Adapter"
NetRuleHardwareDC21143Type = "DC21143 DC21143Adapter"
NetRuleHardwareDC21143Class = {"DC21143Adapter basic"}
AdapterDC21143Type = 5 ;; PCI board
HelpDC21143Id = 50
DC21143CFID = 1642513 ;; 0x00191011
ProductHardwareEB40Title = "Intel EB40 21040 based Evaluation board"
NetRuleHardwareEB40Type = "EB40 EB40Adapter"
NetRuleHardwareEB40Class = {"EB40Adapter basic"}
AdapterEB40Type = 5 ;; PCI board
HelpEB40Id = 100
EB40CFID = 135185 ;; 0x00021011
ProductHardwareEB41Title = "Intel EB41 21041 based Evaluation board"
NetRuleHardwareEB41Type = "EB41 EB41Adapter"
NetRuleHardwareEB41Class = {"EB41Adapter basic"}
AdapterEB41Type = 5 ;; PCI board
HelpEB41Id = 110
EB41CFID = 1314833 ;; 0x00141011
ProductHardwareEB140Title = "Intel EB140 21140 based 10/100 mpbs Evaluation board"
NetRuleHardwareEB140Type = "EB140 EB140Adapter"
NetRuleHardwareEB140Class = {"EB140Adapter basic"}
AdapterEB140Type = 5 ;; PCI board
HelpEB140Id = 120
EB140CFID = 593937 ;; 0x00091011
ProductHardwareEB142Title = "Intel EB142 21142 based 10/100 mpbs Evaluation board"
NetRuleHardwareEB142Type = "EB142 EB142Adapter"
NetRuleHardwareEB142Class = {"EB142Adapter basic"}
AdapterEB142Type = 5 ;; PCI board
HelpEB142Id = 130
EB142CFID = 1642513 ;; 0x00191011
ProductHardwareEB143Title = "GFC2202 10/100 PCI Fast Ethernet Adapter"
NetRuleHardwareEB143Type = "EB143 EB143Adapter"
NetRuleHardwareEB143Class = {"EB143Adapter basic"}
AdapterEB143Type = 5 ;; PCI board
HelpEB143Id = 140
EB143CFID = 1642513 ;; 0x00191011
ProductHardwareMULTIATitle = "DEC multia's Ethernet Controller"
NetRuleHardwareMULTIAType = "MULTIA MULTIAAdapter"
NetRuleHardwareMULTIAClass = {"MULTIAAdapter basic"}
AdapterMULTIAType = 5 ;; PCI board
HelpMULTIAId = 200
MULTIACFID = 135185 ;; 0x00021011
SiaRegister0 = 12353 ;; CSR13 = 0x3041
SiaRegister1 = 0 ;; CSR14 = 0x0000
SiaRegister2 = 6 ;; CSR15 = 0x0006
ProductHardwareDE434Title = "DEC DE434 EtherWORKS Turbo PCI TP Adapter"
NetRuleHardwareDE434Type = "DE434 DE434Adapter"
NetRuleHardwareDE434Class = {"DE434Adapter basic"}
AdapterDE434Type = 5 ;; PCI board
HelpDE434Id = 210
DE434CFID = 135185 ;; 0x00021011
ProductHardwareDE435Title = "DEC DE435 EtherWORKS Turbo PCI Combo Adapter"
NetRuleHardwareDE435Type = "DE435 DE435Adapter"
NetRuleHardwareDE435Class = {"DE435Adapter basic"}
AdapterDE435Type = 5 ;; PCI board
HelpDE435Id = 220
DE435CFID = 135185 ;; 0x00021011
ProductHardwareDE450Title = "DEC DE450 EtherWORKS Turbo PCI Combo Adapter"
NetRuleHardwareDE450Type = "DE450 DE450Adapter"
NetRuleHardwareDE450Class = {"DE450Adapter basic"}
AdapterDE$50Type = 5 ;; PCI board
HelpDE450Id = 240
DE450CFID = 1314833 ;; 0x00141011
ProductHardwareDE500Title = "DEC DE500 FastEtherWORKS 10/100 PCI Adapter"
NetRuleHardwareDE500Type = "DE500 DE500Adapter"
NetRuleHardwareDE500Class = {"DE500Adapter basic"}
AdapterDE500Type = 5 ;; PCI board
HelpDE500Id = 250
DE500CFID = 593937 ;; 0x00091011
ProductHardwareDE425Title = "DEC DE425 EISA Ethernet Adapter"
NetRuleHardwareDE425Type = "DE425 DE425Adapter"
NetRuleHardwareDE425Class = {"DE425Adapter basic"}
AdapterDE425Type = 2 ;; EISA board
DE425CFID = 135185 ;; 0x00021011
DE425_1BYTE = 1346544400 ;;Compressed EISA ID "DEC4250"
EISA_MASK = 4043309055
NetRuleHardwareBindForm = " yes yes container"
ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion"
ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters"
[GeneralConstants]
from = ""
to = ""
ExitCodeOk = 0
ExitCodeCancel = 1
ExitCodeFatal = 2
KeyNull = ""
MAXIMUM_ALLOWED = 33554432
RegistryErrorIndex = NO_ERROR
KeyProduct = ""
KeyParameters = ""
TRUE = 1
FALSE = 0
NoTitle = 0
ExitState = "Active"
OldVersionExisted = $(FALSE)
DriverPath = $(!STF_NTPATH)\drivers
SystemsoftPresent = $(FALSE)
[date]
Now = {} ? $(!LIBHANDLE) GetSystemDate
;---------------------------------------------------------------------------
; 1. Identify
;
; DESCRIPTION: To verify that this INF deals with the same type of options
; as we are choosing currently.
;
; INPUT: None
;
; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL
; $($R1): Option Type (COMPUTER ...)
; $($R2): Diskette description
;---------------------------------------------------------------------------
[Identify]
read-syms Identification
set Status = STATUS_SUCCESSFUL
set Identifier = $(OptionType)
set Media = #("Source Media Descriptions", 1, 1)
Return $(Status) $(Identifier) $(Media)
;------------------------------------------------------------------------
; 2. ReturnOptions:
;
; DESCRIPTION: To return the option list supported by this INF and the
; localised text list representing the options.
;
;
; INPUT: $($0): Language used. ( ENG | FRN | ... )
;
; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL |
; STATUS_NOLANGUAGE
; STATUS_FAILED
; STATUS_NOTSUPPORTED
;
; $($R1): Option List
; $($R2): Option Text List
;------------------------------------------------------------------------
[ReturnOptions]
set Status = STATUS_FAILED
set OptionList = {}
set OptionTextList = {}
; check if language requested is supported
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) in $(LanguageList)
ifstr(i) $($1) == ""
goto returnoptions
endif
; check if platform requested is supported
set PlatformList = ^(PlatformsSupported, 1)
Ifcontains(i) $($1) in $(PlatformList)
goto returnoptions
else
set Status = STATUS_NOTSUPPORTED
goto finish_ReturnOptions
endif
else
set Status = STATUS_NOLANGUAGE
goto finish_ReturnOptions
endif
;form a list of all options and another of all the represnting text
returnoptions = +
set OptionList = ^(Options, 1)
set OptionTextList = ^(OptionsText$($0), 1)
set Status = STATUS_SUCCESSFUL
finish_ReturnOptions = +
Return $(Status) $(OptionList) $(OptionTextList)
;------------------------------------------------------------------------
;
; InstallOption:
;
; This section is shelled to by main installation processing
; or by NCPASHEL.INF during reconfig, removal, update, etc.
;
;
; FUNCTION: To copy files representing Options
; To configure the installed option
; To update the registry for the installed option
;
; INPUT: $($0): Language to use
; $($1): OptionID to install
; $($2): SourceDirectory
; $($3): AddCopy (YES | NO)
; $($4): DoCopy (YES | NO)
; $($5): DoConfig (YES | NO)
;
; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL |
; STATUS_NOLANGUAGE |
; STATUS_USERCANCEL |
; STATUS_FAILED
;
;------------------------------------------------------------------------
[InstallOption]
set Option = $($1)
set SrcDir = $($2)
set AddCopy = $($3)
set DoCopy = $($4)
set DoConfig = $($5)
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) NOT-IN $(LanguageList)
Return STATUS_NOLANGUAGE
endif
set-subst LF = "\n"
read-syms GeneralConstants
read-syms FileConstants
set NetRuleSoftwareBindable = $($R1)
read-syms DialogConstants$(!STF_LANGUAGE)
ifstr(i) $(!NTN_Origination) == "NCPA"
set Continue = "OK"
endif
read-syms FileConstants$(!STF_LANGUAGE)
detect date
set-title $(Function$(Option)Title)
set to = Begin
set from = Begin
set CommonStatus = STATUS_SUCCESSFUL
EndWait
Begin = +
Ifstr(i) $(!NTN_InstallMode) == deinstall
set StartLabel = removeadapter
else-Ifstr(i) $(!NTN_InstallMode) == Update
set StartLabel = UpgradeSoftware
else-Ifstr(i) $(!NTN_InstallMode) == bind
set StartLabel = bindingadapter
else-Ifstr(i) $(!NTN_InstallMode) == configure
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
set from = end
set to = end
goto nonfatalinfo
else-ifstr(i) $(Option) == "DE425"
Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_HARDWARE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
set from = end
set to = end
goto nonfatalinfo
else
set StartLabel = configureadapter
endif
else
set StartLabel = installadapter
set OEM_ABANDON_OPTIONS = {}
set OEM_ABANDON_SOFTWARE = FALSE
set OEM_ABANDON_ON = TRUE
endif
set from = $(fatal)
set to = $(fatal)
goto $(StartLabel)
installadapter = +
;--DEBUG -------------------------------------
set !G:DebugOutputControl = $(ON)
;---------------------------------------------
;;for systemsoft cardwizard
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADBKeyName) $(MAXIMUM_ALLOWED) PCMCIADBKey
ifstr $(PCMCIADBKey) == $(NULL)
CloseRegKey $(PCMCIADBKey)
Debug-Output "PCMCIA service not present"
else
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADBKeyName)"\"$(DC21X4Manufacture) $(MAXIMUM_ALLOWED) PCMCIA$(DC21X4Manufacture)Key
ifstr $(PCMCIA$(DC21X4Manufacture)Key) == $(NULL)
debug-output "Adding "$(PCMCIADBKeyName)"\"$(DC21X4Manufacture)
CreateRegKey $(PCMCIADBKey) {$(DC21X4Manufacture), 0, 0} "" $(MAXIMUM_ALLOWED) "" PCMCIA$(DC21X4Manufacture)Key
else
debug-output "Manufacture sub key already exist"
endif
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADBKeyName)"\"$(DC21X4Manufacture)"\"$(DC21X4Model) $(MAXIMUM_ALLOWED) PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key
ifstr $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) == $(NULL)
debug-output "Adding "$(PCMCIADBKeyName)"\"$(DC21X4Manufacture)"\"$(DC21X4Model)
CreateRegKey $(PCMCIA$(DC21X4Manufacture)Key) {$(DC21X4Model), 0, 0} "" $(MAXIMUM_ALLOWED) "" PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key
SetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) {Driver, 0, $(!REG_VT_SZ),$(ProductSoftwareName)}
SetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) {DeviceType,0,$(!REG_VT_SZ),"NET"}
SetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) {InfFileName,0,$(!REG_VT_SZ),$(STF_CONTEXTINFNAME)}
else
debug-output "Device sub key already exist"
GetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key),+"Driver",GetData
ifstr *($(GetData),7) != $(ProductSoftwareName)
SetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) {Driver, 0, $(!REG_VT_SZ),$(ProductSoftwareName)}
SetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) {DeviceType,0,$(!REG_VT_SZ),"NET"}
SetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) {InfFileName,0,$(!REG_VT_SZ),$(STF_CONTEXTINFNAME)}
endif
endif
CloseRegKey $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key)
CloseRegKey $(PCMCIA$(DC21X4Manufacture)Key)
CloseRegKey $(PCMCIADBKey)
endif
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIARMPKeyName) $(MAXIMUM_ALLOWED) PCMCIARMKey
ifstr $(PCMCIARMKey) == $(NULL)
CloseRegKey $(PCMCIARMKey)
Debug-Output "Systemsoft CardWizard service not present"
else
set SystemsoftPresent = $(TRUE)
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIARMKeyName) $(MAXIMUM_ALLOWED) PCMCIA$(DC21X4MacDB)Key
ifstr $(PCMCIA$(DC21X4MacDB)Key) == $(NULL)
debug-output "Adding "$(PCMCIARMKeyName)
CreateRegKey $(PCMCIARMKey) {"MacDataBase" , 0, 0} "" $(MAXIMUM_ALLOWED) "" PCMCIA$(DC21X4MacDB)Key
CloseRegKey PCMCIA$(DC21X4MacDB)Key
endif
CloseRegKey $(PCMCIARMKey)
endif
;;this addition is for hot swap capability
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIARMKeyName) $(MAXIMUM_ALLOWED) PCMCIARMKey
ifstr $(PCMCIARMKey) == $(NULL)
CloseRegKey $(PCMCIARMKey)
Debug-Output "Systemsoft CardWizard service not present"
else
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIARMKeyName)"\"$(DC21X4Manufacture) $(MAXIMUM_ALLOWED) PCMCIA$(DC21X4Manufacture)Key
ifstr $(PCMCIA$(DC21X4Manufacture)Key) == $(NULL)
debug-output "Adding "$(PCMCIARMKeyName)"\"$(DC21X4Manufacture)
CreateRegKey $(PCMCIARMKey) {$(DC21X4Manufacture), 0, 0} "" $(MAXIMUM_ALLOWED) "" PCMCIA$(DC21X4Manufacture)Key
else
debug-output "Manufacture sub key already exist"
endif
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIARMKeyName)"\"$(DC21X4Manufacture)"\"$(DC21X4Model) $(MAXIMUM_ALLOWED) PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key
ifstr $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) == $(NULL)
debug-output "Adding "$(PCMCIARMKeyName)"\"$(DC21X4Manufacture)"\"$(DC21X4Model)
CreateRegKey $(PCMCIA$(DC21X4Manufacture)Key) {$(DC21X4Model), 0, 0} "" $(MAXIMUM_ALLOWED) "" PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key
SetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) {MacDriverHandle, 0, $(!REG_VT_DWORD),0}
SetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) {MacDriverName,0,$(!REG_VT_SZ),$(ProductSoftwareName)}
SetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) {MacDriverState,0,$(!REG_VT_DWORD),1}
SetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) {MacDriverVersion,0,$(!REG_VT_DWORD),$(ProductMajorVersion)$(ProductMinorVersion)}
SetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) {MacSwapCapability,0,$(!REG_VT_DWORD),2}
else
debug-output "Device sub key already exist"
GetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key),+"MacDriverName",GetData
ifstr *($(GetData),7) != $(ProductSoftwareName)
SetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) {MacDriverHandle, 0, $(!REG_VT_DWORD),0}
SetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) {MacDriverName,0,$(!REG_VT_SZ),$(ProductSoftwareName)}
SetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) {MacDriverState,0,$(!REG_VT_DWORD),1}
SetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) {MacDriverVersion,0,$(!REG_VT_DWORD),$(ProductMajorVersion)$(ProductMinorVersion)}
SetRegValue $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key) {MacSwapCapability,0,$(!REG_VT_DWORD),2}
endif
endif
CloseRegKey $(PCMCIA$(DC21X4Manufacture)$(DC21X4Model)Key)
CloseRegKey $(PCMCIA$(DC21X4Manufacture)Key)
CloseRegKey $(PCMCIARMKey)
endif
;;;
;
; First, check whether the same version of the software exists
;--------------------------------------------
; FOR DEBUGGING
; to debug the inf file change the OFF to ON
set !G:DebugOutputControl = $(OFF)
; you will then be able to see debug prints of this kind:
Debug-Output "oemsetup.inf: @#!$%"
;--------------------------------------------
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
; Same version already existed in the local machine
; Popup the dialog and ask the user whether he wants to continue
CloseRegKey $(KeyProduct)
ifstr(i) !(NTN_RegBase) == $(ProductKeyName)
;Cannot install the same software again
Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+
$(ProductVersion)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
goto end
else
; Add new adapter card?
Shell $(UtilityInf), CardExistedDlg
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) != "OK"
set CommonStatus = STATUS_USERCANCEL
goto end
endif
set OldVersionExisted = $(TRUE)
endif
Endif
ifstr(i) $(DoCopy) == "YES"
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
Set SrcDir = $($R1)
install "Install-Hlp"
endif
Goto installproduct
configureadapter = +
Ifstr(i) $(KeyProduct) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) == $(KeyNull)
Set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
Goto fatalregistry
Endif
Endif
Shell $(UtilityInf) FindService, $(KeyProduct)
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Endif
Ifstr(i) $($R0) != NO_ERROR
Goto fatalregistry
endif
set KeyParameters = $($R2)
CloseRegKey $($R1)
Ifstr $(KeyParameters) == $(KeyNull)
set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
goto fatalregistry
endif
set OldVersionExisted = $(TRUE)
set ValueName = ""
set ValueData = ""
set ValueStr = ""
set ValueList = {}
; Get the old values from the Registry [Get Values]
EnumRegValue $(KeyParameters) ValueList
ForListDo $(ValueList)
set ValueItem = $($)
set ValueName = *($(ValueItem),1)
set ValueData = *($(ValueItem),4)
Ifstr(i) $(ValueName) == "ConnectionType"
set ConnectionIndex = $(ValueData)
endif
EndForListDo
set ConnectionValue = *($(ConnectionList), ~($(ConnectionValues),$(ConnectionIndex)))
ifstr(i) $(ConnectionValue) == ""
set ConnectionValue = *($(ConnectionList), 2)
endif
adapteroptions = +
ifstr(i) $(Option) != "DE425"
set from = adapteroptions
read-syms FileDependentDlg$(!STF_LANGUAGE)
SetHelpFile $(!STF_WINDOWSSYSPATH)"\"$(OptionHelpFile) $(MinHelpId) $(MaxHelpId) $(Help$(Option)Id)
ui start "InputDlg"
ifstr(i) $(DLGEVENT) == "CONTINUE"
set ConnectionIndex = $(Combo1Out)
ui pop 1
else-ifstr(i) $(DLGEVENT) == "BACK"
set CommonStatus = STATUS_USERCANCEL
ui pop 1
goto end
else
ui pop 1
goto end
endif
set ConnectionValue = *($(ConnectionValues), ~($(ConnectionList),$(ConnectionIndex)))
ifstr(i) $(!NTN_InstallMode) == configure
goto updateparameters
endif
endif
installproduct =+
StartWait
ifstr(i) $(Option) == "DE425"
Shell $(UtilityInf), EISAFindBus, $($(Option)_1BYTE),$(EISA_MASK)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr $($R0) != "NO_ERROR"
set Error = $($R0)
goto fatal
endif
ifstr(i) $($R1) == {}
set Error = $(CANNOT_FIND_ANY_CARD)
set CommonStatus = USER_CANCEL
set from = end
goto nonfatal
endif
set AdapterList = $($R1)
else
set-div DeviceID = $($(Option)CFID) 65536
Shell $(UtilityInf), GetPCIInformation, $(VendorID) $(DeviceID)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R0) == {}
set Error = $(CANNOT_FIND_ANY_CARD)
set CommonStatus = USER_CANCEL
set from = end
goto nonfatal
endif
set AdapterList = $($R0)
endif
ifint $(OldVersionExisted) == $(FALSE)
Ifstr(i) $(DoCopy) == "YES"
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
Set SrcDir = $($R1)
Endif
install "Install-Option"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
endif
Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), +
$(ProductSoftwareName), +
$(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), +
$(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+
$(NetEventDLL)
Set OEM_ABANDON_SOFTWARE = TRUE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
; At this point:
; $R1 contains the product version key handle;
; $R2 contains the NetRules subkey handle;
; $R3 contains the new Services key handle;
; $R4 contains the Parameters key
; $R5 contains the Linkage Key
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
CloseRegKey $($R4)
CloseRegKey $($R5)
goto fatalregistry
endif
Set SoftProductKey = $($R1)
Set SoftNetRuleKey = $($R2)
Set SoftServiceKey = $($R3)
Set SoftParameterKey = $($R4)
Set SoftLinkageKey = $($R5)
set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+
{MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+
{MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+
{Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(SoftProductKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftParameterKey)
CloseRegKey $(SoftLinkageKey)
goto fatalregistry
endif
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+
{use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, +
{bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, +
{bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareSWBindable)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(SoftNetRuleKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftParameterKey)
CloseRegKey $(SoftLinkageKey)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
goto fatalregistry
endif
endif
ForListDo $(AdapterList)
set BusNum = *($($),1)
set DeviceNum = *($($),2)
set FunctionNum = *($($),3)
ifstr(i) $(Option) == "DE425"
Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(BusNum), +
$(DeviceNum), $(ProductHardware$(Option)Description), $(ProductHardwareName) "YES"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr $($R0) != "NO_ERROR"
set Error = $($R0)
goto fatal
endif
ifstr(i) $($R1) != "YES"
Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)
ifint $($R4) != -1
Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), +
$(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
endif
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
goto fatalregistry
endif
Set HardNetCardKey = $($R1)
Set HardNetRuleKey = $($R2)
Set HardParameterKey = $($R3)
set AdapterNumber = $($R4)
set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+
{Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+
{ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(HardNetCardKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set BusTypeNum = 2
set NewValueList = {{AdapterType,$(NoTitle),$(!REG_VT_DWORD),$(Adapter$(Option)Type)},+
{BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+
{MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+
{BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNum)},+
{SlotNumber,$(NoTitle),$(!REG_VT_DWORD),$(DeviceNum)},+
{AdapterCFID,$(NoTitle),$(!REG_VT_DWORD),$($(Option)CFID)}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardware$(Option)Type)},+
{bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardware$(Option)Class)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(HardNetRuleKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
CloseRegKey $(HardNetCardKey)
CloseRegKey $(HardNetRuleKey)
CloseRegKey $(HardParameterKey)
endif
else
Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(BusNum), +
$(DeviceNum), $(ProductHardware$(Option)Description), $(ProductHardwareName) "YES"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr $($R0) != "NO_ERROR"
set Error = $($R0)
goto fatal
endif
ifstr(i) $($R1) != "YES"
ifstr(i) $(!STF_GUI_UNATTENDED) != "YES"
read-syms FileDependentDlg$(!STF_LANGUAGE)
SetHelpFile $(!STF_WINDOWSSYSPATH)"\"$(OptionHelpFile) $(MinHelpId) $(MaxHelpId) $(Help$(Option)Id)
ui start "InputDlg"
ifstr(i) $(DLGEVENT) == "CONTINUE"
set ConnectionIndex = $(Combo1Out)
ui pop 1
else-ifstr(i) $(DLGEVENT) == "BACK"
set CommonStatus = STATUS_USERCANCEL
ui pop 1
goto end
else
ui pop 1
goto end
endif
endif
Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)
ifint $($R4) != -1
Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
endif
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
goto fatalregistry
endif
set ConnectionValue = *($(ConnectionValues), ~($(ConnectionList),$(ConnectionIndex)))
; At this point:
; $R1 Registry key variable for HARDWARE\Netcard\(n)
; $R2 Registry key variable for HARDWARE\Netcard\(n)\\NetRules
; $R3 Registry key handle for <service>\Parameters key
; $R4 Adapter number assigned to adapter
; $R5 Service name generated by combining svc name with adapter number
Set HardNetCardKey = $($R1)
Set HardNetRuleKey = $($R2)
Set HardParameterKey = $($R3)
set AdapterNumber = $($R4)
set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+
{Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+
{ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(HardNetCardKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set BusTypeNum = 5
ifint $(SystemsoftPresent) == $(TRUE)
set NewValueList = {{AdapterType,$(NoTitle),$(!REG_VT_DWORD),$(Adapter$(Option)Type)},+
{MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+
{BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+
{AdapterCFID,$(NoTitle),$(!REG_VT_DWORD),$($(Option)CFID)},+
{PCMCIA,$(NoTitle),$(!REG_VT_DWORD),1}}
else
set NewValueList = {{AdapterType,$(NoTitle),$(!REG_VT_DWORD),$(Adapter$(Option)Type)},+
{MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+
{BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+
{AdapterCFID,$(NoTitle),$(!REG_VT_DWORD),$($(Option)CFID)}}
endif
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifint $($(Option)CFID) == $(DC21041CFID)
set NewValueList = {{SnoozeMode,$(NoTitle),$(!REG_VT_DWORD),0}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set NewValueList = {{NwayProtocol,$(NoTitle),$(!REG_VT_DWORD),1}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
endif
ifint $($(Option)CFID) == $(DC21142CFID)
set NewValueList = {{StoreAndForward,$(NoTitle),$(!REG_VT_DWORD),$(StoreAndForward)},+
{SnoozeMode,$(NoTitle),$(!REG_VT_DWORD),0}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set NewValueList = {{NwayProtocol,$(NoTitle),$(!REG_VT_DWORD),1}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
endif
ifint $($(Option)CFID) == $(DC21143CFID)
set NewValueList = {{StoreAndForward,$(NoTitle),$(!REG_VT_DWORD),$(StoreAndForward)},+
{SnoozeMode,$(NoTitle),$(!REG_VT_DWORD),0}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
endif
ifint $($(Option)CFID) == $(DE450CFID)
set NewValueList = {{SnoozeMode,$(NoTitle),$(!REG_VT_DWORD),0}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
endif
ifint $($(Option)CFID) == $(DC21140CFID)
set NewValueList = {{StoreAndForward,$(NoTitle),$(!REG_VT_DWORD),$(StoreAndForward)},+
{TransmitThreshold100,$(NoTitle),$(!REG_VT_DWORD),$(TxmThreshold100)},+
{SnoozeMode,$(NoTitle),$(!REG_VT_DWORD),0}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
endif
ifstr(i) $(Option) == "MULTIA"
set NewValueList = {{ExternalSia,$(NoTitle),$(!REG_VT_DWORD),1},+
{SiaRegister0,$(NoTitle),$(!REG_VT_DWORD),$(SiaRegister0)},+
{SiaRegister1,$(NoTitle),$(!REG_VT_DWORD),$(SiaRegister1)},+
{SiaRegister2,$(NoTitle),$(!REG_VT_DWORD),$(SiaRegister2)}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
endif
set NewValueList = {{ConnectionType,$(NoTitle),$(!REG_VT_DWORD),$(ConnectionValue)}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardware$(Option)Type)},+
{bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardware$(Option)Class)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(HardNetRuleKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
CloseRegKey $(HardNetCardKey)
CloseRegKey $(HardNetRuleKey)
set NewValueList = {{BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNum)},+
{SlotNumber,$(NoTitle),$(!REG_VT_DWORD),$(DeviceNum)},+
{FunctionNumber,$(NoTitle),$(!REG_VT_DWORD),$(FunctionNum)}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
CloseRegKey $(HardParameterKey)
endif
endif
EndForListDo
ifstr(i) $(!STF_GUI_UNATTENDED) == "YES"
Shell $(UtilityInf),AddDefaultNetCardParameters,$(KeyParameters)
endif
EndWait
goto successful
updateparameters =+
set HardParameterKey = $($R3)
set NewValueList = {{ConnectionType,$(NoTitle),$(!REG_VT_DWORD),$(ConnectionValue)}}
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
CloseRegKey $(KeyParameters)
goto successful
bindingadapter =+
set Error = "Binding: Sorry, not yet implemented."
goto fatal
removeadapter = +
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
else
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $(!NTN_RegBase)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
UpgradeSoftware = +
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set !UG_Filename = $($R0)
install "Install-Update"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
goto fatal
endif
SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)}
SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)}
CloseRegKey $(KeyProduct)
else
goto fatalregistry
endif
goto end
successful = +
goto end
abandon = +
ForListDo $(OEM_ABANDON_OPTIONS)
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $($)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
EndForListDo
Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), FALSE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
warning = +
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(to)
else-ifstr(i) $($R1) == "CANCEL"
goto $(from)
else
goto "end"
endif
nonfatalinfo = +
Set CommonStatus = STATUS_USERCANCEL
Set Severity = STATUS
goto nonfatalmsg
nonfatal = +
Set Severity = NONFATAL
goto nonfatalmsg
nonfatalmsg = +
ifstr(i) $(Error) == ""
Set Severity = NONFATAL
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(from)
else
goto "end"
endif
fatalregistry = +
Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
fatal = +
ifstr(i) $(Error) == ""
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
goto setfailed
ShellCodeError = +
set DlgType = "MessageBox"
set STF_MB_TITLE = $(ShellCodeErrorTitle)
set STF_MB_TEXT = $(ShellCodeErrorText)
set STF_MB_TYPE = 1
set STF_MB_ICON = 3
set STF_MB_DEF = 1
ui start "Error Message"
goto setfailed
setfailed = +
set CommonStatus = STATUS_FAILED
ifstr(i) $(OEM_ABANDON_ON) == TRUE
set OEM_ABANDON_ON = FALSE
goto abandon
endif
goto end
end = +
goto term
term = +
Return $(CommonStatus)
[Install-Option]
set STF_VITAL = ""
ifstr(i) $(AddCopy) == "YES"
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
endif
ifstr(i) $(DoCopy) == "YES"
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
endif
Exit
[Install-Hlp]
set STF_VITAL = ""
AddSectionFilesToCopyList Files-Hlp $(SrcDir) $(!STF_WINDOWSSYSPATH)
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
Exit
[Install-Update]
set STF_VITAL = ""
set STF_OVERWRITE = "VERIFYSOURCEOLDER"
AddSectionFilesToCopyList Files-Hlp $(SrcDir) $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
exit
[Source Media Descriptions]
1 = "Intel DC21x4 NDIS 4.0 Driver"
[ProductType]
STF_PRODUCT = Winnt
STF_PLATFORM = I386
STF_PLATFORM = PPC
STF_PLATFORM = Alpha
[Files-Inf]
2, oemsetup.inf, SIZE=1000, RENAME=$(!UG_Filename)
[Files-DC21040]
1,DC21X4.SYS , SIZE=999
[Files-DC21041]
1,DC21X4.SYS , SIZE=999
[Files-DC21140]
1,DC21X4.SYS , SIZE=999
[Files-DC21142]
1,DC21X4.SYS , SIZE=999
[Files-DC21143]
1,DC21X4.SYS , SIZE=999
[Files-EB40]
1,DC21X4.SYS , SIZE=999
[Files-EB41]
1,DC21X4.SYS , SIZE=999
[Files-EB140]
1,DC21X4.SYS , SIZE=999
[Files-EB142]
1,DC21X4.SYS , SIZE=999
[Files-EB143]
1,DC21X4.SYS , SIZE=999
[Files-MULTIA]
1,DC21X4.SYS , SIZE=999
[Files-DE434]
1,DC21X4.SYS , SIZE=999
[Files-DE435]
1,DC21X4.SYS , SIZE=999
[Files-DE450]
1,DC21X4.SYS , SIZE=999
[Files-DE500]
1,DC21X4.SYS , SIZE=999
[Files-DE425]
1,DC21X4.SYS , SIZE=999
[Files-Hlp]
1,DC21X4.HLP , SIZE=999
[LanguagesSupported]
ENG
[OptionsTextENG]
DC21040 = "Intel 21040 based Ethernet Controller"
DC21041 = "Intel 21041 based Ethernet Controller"
DC21140 = "Intel 21140 based 10/100 mpbs Ethernet Controller"
DC21142 = "Intel 21142 based 10/100 mpbs Ethernet Controller"
DC21143 = "Intel 21143 based 10/100 mpbs Ethernet Controller"
EB40 = "Intel EB40 21040 based Evaluation board"
EB41 = "Intel EB41 21041 based Evaluation board"
EB140 = "Intel EB140 21140 based 10/100 mpbs Evaluation board"
EB142 = "Intel EB142 21142 based 10/100 mpbs Evaluation board"
EB143 = "Intel EB143 21143 based 10/100 mpbs Evaluation board"
MULTIA = "DEC multia's Ethernet Controller"
DE434 = "DEC DE434 EtherWORKS Turbo PCI TP Adapter"
DE435 = "DEC DE435 EtherWORKS Turbo PCI Combo Adapter"
DE450 = "DEC DE450 EtherWORKS Turbo PCI Combo Adapter"
DE500 = "DEC DE500 FastEtherWORKS 10/100 PCI Adapter"
DE425 = "DEC DE425 EtherWORKS Turbo EISA Adapter"
[FileConstantsENG]
ProCaption = "Windows NT Setup"
ProCancel = "Cancel"
ProCancelMsg = "Windows NT Networking is not correctly installed. "+
"Are you sure you want to cancel copying files?"
ProCancelCap = "Network Setup Message"
ProText1 = "Copying:"
ProText2 = "To:"
ProductSoftwareDescription = "Intel DC21x4 Driver"
FunctionDC21040Title = "Intel 21040 based Ethernet Controller Setup"
ProductHardwareDC21040Description = "Intel 21040 based Ethernet Controller"
FunctionDC21041Title = "Intel 21041 based Ethernet Controller Setup"
ProductHardwareDC21041Description = "Intel 21041 based Ethernet Controller"
FunctionDC21140Title = "DIntel 21140 based 10/100 mpbs Ethernet Controller Setup"
ProductHardwareDC21140Description = "Intel 21140 based 10/100 mpbs Ethernet Controller"
FunctionDC21142Title = "Intel 21142 based 10/100 mpbs Ethernet Controller Setup"
ProductHardwareDC21142Description = "Intel 21142 based 10/100 mpbs Ethernet Controller"
FunctionDC21143Title = "GFC2202 10/100 PCI Fast Ethernet Adapter Setup"
ProductHardwareDC21143Description = "GFC2202 10/100 PCI Fast Ethernet Adapter"
FunctionEB40Title = "Intel EB40 21040 based Evaluation Board Setup"
ProductHardwareEB40Description = "Intel EB40 21040 based Board"
FunctionEB41Title = "Intel EB41 21041 based Evaluation Board Setup"
ProductHardwareEB41Description = "Intel EB41 21041 based Evaluation Board"
FunctionEB140Title = "Intel EB140 21140 based 10/100 mpbs Evaluation Board Setup"
ProductHardwareEB140Description = "Intel EB140 21140 based Evaluation Board"
FunctionEB142Title = "Intel EB142 21142 based 10/100 mpbs Evaluation Board Setup"
ProductHardwareEB142Description = "Intel EB142 21142 based Evaluation Board"
FunctionEB143Title = "GFC2202 10/100 PCI Fast Ethernet Adapter Setup"
ProductHardwareEB143Description = "GFC2202 10/100 PCI Fast Ethernet Adapter"
FunctionMULTIATitle = "DEC multia's Ethernet Controller Setup"
ProductHardwareMULTIADescription = "DEC multia's Ethernet Controller"
FunctionDE434Title = "DEC DE434 PCI Adapter Card Setup"
ProductHardwareDE434Description = "DEC DE434 EtherWORKS Turbo PCI TP Adapter"
FunctionDE435Title = "DEC DE435 PCI Adapter Card Setup"
ProductHardwareDE435Description = "DEC DE435 EtherWORKS Turbo PCI Combo Adapter"
FunctionDE450Title = "DEC DE450 PCI Adapter Card Setup"
ProductHardwareDE450Description = "DEC DE450 EtherWORKS Turbo PCI Combo Adapter"
FunctionDE500Title = "DEC DE500 PCI Adapter Card Setup"
ProductHardwareDE500Description = "DEC DE500 FastEtherWORKS 10/100 PCI Adapter"
FunctionDE425Title = "DEC DE425 EISA Adapter Card Setup"
ProductHardwareDE425Description = "DEC DE425 EtherWORKS Turbo EISA Adapter"
ConnectionList = ^(ConnectionChoices$(Option), 1)
ConnectionValues = ^(ConnectionChoices$(Option), 2)
NoList = ^(NoChoices, 1)
NoValues = ^(NoChoices, 2)
ShellCodeErrorTitle = "Error: "$(Function$(Option)Title)
ShellCodeErrorText = "Shell Code Error."
CANNOT_FIND_ANY_CARD = "Network card is not present in the system"
[DialogConstantsENG]
Help = "&Help"
Exit = "Cancel"
OK = "OK"
HelpContext = ""
Continue = "Continue"
Cancel = "Cancel"
[FileDependentDlgENG]
DlgText = "Choose the proper cable type for the "+
"network adapter. Select [Help] for a detailled "+
"description of the available options of the list."
DlgTemplate = "ADAP_PROTO_COMBO"
DlgType = "Combination"
Caption = $(Function$(Option)Title)
Combo1Label = "&Connection Type:"
Combo1List = $(ConnectionList)
Combo1Out = $(ConnectionValue)
ComboListItemsIn = {Combo1List}
ComboListItemsOut = {Combo1Out}
EditTextLim = ""
CBOptionsGreyed = {}
MinHelpId = 10
MaxHelpId = 1140
HelpContext = $(Help$(Option)Id)
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.