1. EN-9210V20.zip Driver
2. README.TXT File Contents

README.TXT Driver File Contents (EN-9210V20.zip)

   Workstation for DOS ODI Client

   Introduction:
   -------------
   This document describes the procedure to setup the NetWare v3.X , v4.X
   workstation driver for National Semiconductor DP83820 Gigabit Network
   Adapter.

   Location of Driver:     \NETWARE\DOSODI\DP83820.COM

   Sample Configuration Files:
   ---------------------------
     STARTNET.BAT:
         LSL
         DP83820
         IPXODI
         NETX or VLM (VLM's for NetWare 4.x )

   NET.CFG:

     Link Support
     Buffers 8 1514

     Link Driver DP83820
     SLOT 1                     ;;Select Slot Number (FIRST Board)
     NWAY                       ;;Nway Autodetect Media Mode (Default)
     N100F                      ;;Forced 100M Full-Duplex Nway Capability
     N100H                      ;;Forced 100M Half-Duplex Nway Capability
     N10F                       ;;Forced 10M Full-Duplex Nway Capability
     N10H                       ;;Forced 10M Half-Duplex Nway Capability
     100F                       ;;Forced 100M Full-Duplex Media Mode
     100H                       ;;Forced 100M Half-Duplex Media Mode
     10F                        ;;Forced 10M Full-Duplex Media Mode
     10H                        ;;Forced 10M Half-Duplex Media Mode
     NODE ADDRESS 0223456789AB  ;;Set Override Node Address

    ====================================================================
    NOTICE:
    IEEE 802.3u standard DONOT support 1000Mbps forced media mode,
    so the driver don't support 1000Mbps forced media mode.
    ====================================================================

     FRAME ETHERNET_802.2
     FRAME ETHERNET_802.3
     FRAME ETHERNET_II
     FRAME ETHERNET_SNAP
     PROTOCOL IPX E0 ETHERNET_802.2
     PROTOCOL IPX 0 ETHERNET_802.3
     PROTOCOL IPX 8137 ETHERNET_II
     PROTOCOL IPX 8137 ETHERNET_SNAP


     Link Driver DP83820
     SLOT 2                       ;;Select Slot Number (SECONDARY Board)
     FRAME ETHERNET_802.2
     FRAME ETHERNET_802.3
     FRAME ETHERNET_II
     FRAME ETHERNET_SNAP

     NetWare DOS Requester
     FIRST NETWORK DRIVE = F
     NETWARE PROTOCOL = NDS BIND
     MAX IPG = 0



   Setup Procedures for NetWare 3.11/3.12 Client :
   -----------------------------------------------
      Before you start with the installation process, make sure that
      the  adapter is properly installed and configured. Make sure
      that your NetWare workstation is properly installed.

      1. Copy DP83820.COM from the Driver Diskette subdirectory
         A:\NETWARE\DOSODI to your harddisk.

      2. Create a batch file, or add to your STARTNET.BAT file the commands
         listed above under STARTNET.BAT

      3. Edit the NET.CFG file that you copied over. Edit the file per your
         requirements (see examples above).  If there are two frame types
         listed, whichever frame type is listed first, that is the one that
         the  driver will load.  See above for examples.  The NET.CFG file
         should be in the same directory with the LSL.COM file.


   Setup Procedures for NetWare 4.X Client with vlm:
   -----------------------------------------------
      The  installation utility  INSTALL.EXE  is  located on NetWare's
      "Workstation for DOS" disk. Run INSTALL.EXE from the Workstation
      for DOS Disk.

      The NetWare Client Install program screen will appear.  You must
      complete each of the questions.  These options are specific to your
      needs.

      1. Enter the destination directory for the NetWare Client.
         (The default directory is C:\NWCLIENT).

      2. Gives you the option to automatically update the CONFIG.SYS
         and the AUTOEXEC.BAT files or modify them at a later time
         manually.

      3. Do you wish to install support for MS Windows ? (Y/N)
         (MS Windows Subdirectory: default C:\WINDOWS)

      4. Asks you to select a network driver and provide  configuration
         options.  It uses  the specifications you select to create the
         file NET.CFG. Insert the Realtek drivers disk when prompted for
         the driver disk and specify the driver path A:\NETWARE\DOSODI

      5. Press <Enter> to install