||||||||||||||||||||||||||||||||||||||
Usage of SMK Tablet Driver for Windows NT
||||||||||||||||||||||||||||||||||||||
PDIntroduction
There are four files in this FLOPPY DISK (FD) as follows.
EREADME.TXT ¥¥¥¥¥ Direction for Use (This document file)
ETTABNT.INF ¥¥¥¥¥ Setup information file for Tablet Driver
ETTABNT.SYS ¥¥¥¥¥ Tablet driver system file
ETABCORNT.EXE ¥¥¥ Application program for coordinates correction
coefficiency
QDTo install the Tablet Driver
@ Open the "Control Panel" of Windows and generate Mouse function.
A Select tag of "General" and then click "Change" button to open the
"Select Device" dialog box.
B Click the "Have Disk" button when appear the dialog box of
"Select Device".
C Click "OK" button when appear the dialog box of "Install From Disk".
D When appear the dialog box of "Select Device", select port to connect
to the Tablet and click "OK" button.
E Click the "Close" button after the file was copied.
F Restart your computer.
(Click the "Yes" button when appear the dialog box of
"System Settings Change".)
Note: Eject the FLOPPY DISK before restart the computer.
G Execute the TABCORNT.EXE to work the Tablet Driver.
Note: Tablet does not work until TABCORNT.EXE is executed.
See the following section about usage of TABCORNT.EXE.
H TABCORNT.EXE enable to operate the Tablet.
RDUsage of TABCORNT.EXE
@ Execute the TABCORNT.EXE.
(This application is able to execute from any drive or to copy in
directory.
You can operate any way as follows.)
EInput "A:TABCORNT.EXE" from the dialog box of "Run", then
click "OK" button.
EExecute from "My Computer" directly.
A Following the display message, you push the four corners of Tablet in
order of left-upper, right-upper, left-bottom, right-bottom.
B After finishing the above operation, you can use the Tablet.
(No need to restart computer again.)
SDTTABNT.INF
TTAB.INF file is the text file contained the hardware configuration for
serial ports.
This consists of introduction area, port configuration area (part of
"##### SMK Tablet on COM? #####") and common configuration area (part of
"----- Common Use Section -----").
Default settings of COM ports are following.
COM1 ¥¥¥ AddressF3F8hAIRQF4
COM2 ¥¥¥ AddressF2F8hAIRQF3
COM3 ¥¥¥ AddressF3E8hAIRQF4
COM4 ¥¥¥ AddressF2E8hAIRQF3
COM5 ¥¥¥ AddressF270hAIRQF11
To change this hardware settings, edit the Address and IRQ value of end of
2 and 3 lines in the "Add Registry Section" (part of [TtabNT_com?_AddReg] )
by text editor.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
ExDChange the COM1 setting to "AddressF3E8hAIRQF3" from
"AddressF3F8hAIRQF4".
[TtabNT_com1_AddReg]
HKLM,SYSTEM\ControlSet001\...\Parameters,COMPort,0x00010001,1
HKLM,SYSTEM\ControlSet001\...\Parameters,IRQNo,0x00010001,4
HKLM,SYSTEM\ControlSet001\...\Parameters,Address,0x00010001,0x3f8
|
|
V
[TtabNT_com1_AddReg]
HKLM,SYSTEM\ControlSet001\...\Parameters,COMPort,0x00010001,1
HKLM,SYSTEM\ControlSet001\...\Parameters,IRQNo,0x00010001,3
HKLM,SYSTEM\ControlSet001\...\Parameters,Address,0x00010001,0x3e8
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.