PCI Fast Ethernet Adapter NetWare DOS ODI Server Driver for Netware 3.1x Installation Guide ======================================================================= NetWare DOS ODI Server Driver Installation (NetWare 3.11) ========================================================= Installation Procedure: ----------------------- Before you start with the installation process, make sure that the Novell NetWare 386 V3.11 server is properly installed. Similarly, your adapter should also be properly installed in your workstation. 1. Insert the Driver Diskette into drive A: and check the contents of subdirectory \NETWARE\SERVER.31X. It should contain the following files: MXICSERV.LAN Ä Novell NetWare 3.1X Server Driver for PCI Fast Ethernet Adapter. AUTOEXEC.NCF ETHERTSM.NLM LSLENH.NLM MONITOR.NLM MSM31X.NLM MXICSERV.LDI README.TXT NBI31X.NLM PATCHMAN.NLM 2. Copy the above LAN files from the Driver Diskette into the NetWare 386 subdirectory of your server. 3. Run SERVER.EXE from your server. You will see a series of NetWare messages on the screen. 4. Before loading the server driver, you must load above those extension name named NLM driver. You can refer to the autoexec.ncf file in \NETWARE\SERVER.31X directory. 5. When the NetWare 386 prompt appears (indicated by a colon), load your server driver. Simply type: : LOAD [c:]\<PATHNAME>\MXICSERV FRAME=ETHERNET_802.3 [Speed/Mode Type] <Enter> Speed/Duplex Types: 10HD ...... 10Mbps Half Duplex 10FD ...... 10Mbps Full Duplex 100HD ...... 100Mbps Half Duplex 100FD ...... 100Mbps Full Duplex AUTOSENSE ...... Auto-Negotiation 6. Bind IPX to the adapter LAN driver. At the NetWare server prompt, type: :BIND IPX MXICSERV <Enter> 7. After pressing <Enter>, the computer will prompt you for the Network Number. For details on how to assign this number, please check your NetWare 386 Installation Manual. NetWare DOS ODI Server Driver Installation (NetWare 3.12) ========================================================= Installation Procedure: ----------------------- Before you start with the installation process, make sure that the Novell NetWare 386 V3.12 server is properly installed. Similarly, your adapter should also be properly installed in your workstation. 1. Insert the Driver Diskette into drive A: and check the contents of subdirectory \NETWARE\SERVER.31X It should contain the following files: MXICSERV.LAN Ä Novell NetWare 3.1X Server Driver for PCI Fast Ethernet Adapter. AUTOEXEC.NCF ETHERTSM.NLM LSLENH.NLM MONITOR.NLM MSM31X.NLM MXICSERV.LAN README.TXT NBI31X.NLM PATCHMAN.NLM 2. Copy the above files into the NetWare 386 subdirectory of your server. 3. Run SERVER.EXE from your server. You will see a series of NetWare messages on the screen. 4. Before loading the server driver, you must load MSM31X.NLM first and then load ETHERTSM.NLM. 5. When the NetWare 386 prompt appears (indicated by a colon), load your server driver. Simply type: : LOAD [c:]\<PATHNAME>\MXICSERV FRAME=ETHERNET_802.3 [Speed/Mode Type] <Enter> Speed/Duplex Types: 10HD ...... 10Mbps Half Duplex 10FD ...... 10Mbps Full Duplex 100HD ...... 100Mbps Half Duplex 100FD ...... 100Mbps Full Duplex AUTOSENSE ...... Auto-Negotiation 6. Bind IPX to the adapter LAN driver. At the NetWare server prompt, type: :BIND IPX MXICSERV <Enter> 7. After pressing <Enter>, the computer will prompt you for the Network Number. For details on how to assign this number, please check your NetWare 386 Installation Manual. Installation notes: ------------------- 1. If you are doing the PERFORM3 or ENDURNCE test, you'd better add the followings in your AUTOEXEC.NCF of the server, Set Immediate Purge Of Deleted Files=ON 2. You had better add the followings in the STARTUP.NCF: Set Reserved buffers below 16 meg 200 Set maximum Physical receive Packet Size = 1520 set minimum packet receive buffers = 150 3. You may specify the line speed and mode type you need in the AUTOEXEC.NCF file. LOAD [c:]\<PATHNAME>\MXICSERV FRAME=ETHERNET_802.3 [Speed/Mode Type] Speed/Duplex Types: 10HD ...... 10Mbps Half Duplex 10FD ...... 10Mbps Full Duplex 100HD ...... 100Mbps Half Duplex 100FD ...... 100Mbps Full Duplex AUTOSENSE ...... Auto-Negotiation Brand and product names are trademarks of their respective companies. ==End Of File==Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.