Silicom Serial Card. Last update: June 1, 1997. This file provides general information not available in the user manual. Please read this file before installing the product. This file provides information for Ms Dos users. If you are running Windows, setup the Online User Manual as described in chapter 1 of this document. Contents: --------- 1. How to install the Online User Manual under Windows. 2. Hardware notes. 3. Installing the Silicom Serial Card Support Driver manually. 4. Memory managers. 5. The Silicom Serial Card Support Driver parameters. 6. Technical Support. 1. How to install the Online User Manual under Windows ------------------------------------------------------ 1. Start Windows. 2. Insert the software diskette into the PC diskette drive. 3. From the Program Manager, select "File" menu. (For Windows 95, click on "Start" button). 4. Select "Run". 5. Type "A:\SETUP" and select OK. 6. The setup will install the Online User Manual. 2. Hardware notes. ----------------- The Silicom Serial Card supports "Hot" insertion and removal. Thus, the PC Card can be inserted into and/or removed from a PC that is either switched off or switched on. The Silicom Serial Card supports Card Services version 2.10, including automatic resources allocation and Plug-and-Play features. If you have a version of Card and Socket Services software before 2.10, please contact your computer/Operating System manufacturer to receive an upgrade. 3. Installing Silicom Serial Card Support Driver manually. ----------------------------------------------------------- In special cases manual installation might be necessary. The following sections describe the required procedures. In order to work with the Silicom Serial Card without Card and Socket Services, you need to install the Silicom Serial Card Support Driver. Add the following line to your CONFIG.SYS file: DEVICE = path\SRSDRV.EXE [parameters] The Silicom Serial Card Support Driver may also be loaded from the DOS command prompt or from a batch file: path\SRSDRV.EXE [parameters] Without command line parameters, the driver uses default or auto-configured settings. To customize the driver's settings, use the following syntax: SRSDRV [/irq=x] [/port=xxx] [/mem=xxxx] [/help] [/?] [socket=0|1] [type=x] [noenable] [/base=xxx] [/fast=1|2|3] The full list of the parameters is described in the following section of this document. IMPORTANT! Incorrect use of parameters may result in faulty operation of the PC Card. Make sure you are familiar with the different parameters before using them. 4. Memory managers ------------------ If a memory manager is loaded you may experience memory setting conflicts. To avoid this potential conflict, modify the memory manager command line in the CONFIG.SYS file to exclude the memory range used by the Serial PC Card. For example: For EMM386, type (add) the following: device=c:\windows\emm386.exe x=d000-d400 For 386Max, type the following: device=c:\386max.sys pro=c:\386max.pro ram=d000-d400 5. The Silicom Serial Card Support Driver parameters. ------------------------------------------------------ +-----------+-----+----+----------------------------------------------------+ | Keyword |Range|Def.| Description | +-----------+-----+----+----------------------------------------------------+ |irq | 3-4 |auto| Specifies the Interrupt line for the Serial Card. | +-----------+-----+----+----------------------------------------------------+ |port | 100-|auto| Specifies the modem (COM) port address.The default | | |F000 | | is the first available free COM port address. | +-----------+-----+----+----------------------------------------------------+ |mem |D000-|D000| Specifies the segment of RAM where the card | | |DC00 | | will map its attribute memory. | +-----------+-----+----+----------------------------------------------------+ |socket | 0 |auto| Specifies the host computer PCMCIA slot where the | | | 1 | | PC Card is inserted. | | | | | The use of this parameter disables socket auto | | | | | detection by the driver. | +-----------+-----+----+----------------------------------------------------+ |fast | 1 | 0 | Adds additional I/O wait states if non-zero value | | | 2 | | is specified. This parameter is required by some | | | 3 | | computers that have a fast I/O bus. | +-----------+-----+----+----------------------------------------------------+ |Base | n/a |auto| Specifies the base I/O address of the host | | | | | computer PCMCIA Controller. Can only be used for a | | | | | PCMCIA controller with non-standard I/O address | | | | | settings. | +-----------+-----+----+----------------------------------------------------+ 6. Technical Support. ----------------- Silicom's international technical support team offers free worldwide product support. World-Wide Web on the Internet ------------------------------ Point your Internet browser at http://www.silicom.co.il for the latest software drivers, updates, and information on the complete Silicom product line. Software page URL is: http://www.silicom.co.il/drivers.htm FTP site -------- Open a FTP connection to ftp.silicom.co.il to download the latest software drivers and updates. Log in as anonymous user. Additional support ------------------ If additional information is required, please contact your local supplier or the local Silicom office nearest you. North America: Phone: (201) 529-1121 FAX: (201) 529-0906 E-mail: techsup@silicom-usa.com Israel: Phone: (972) 9767-8989 FAX: (972) 9765-1977 E-mail: techsup@silicom.co.il Before contacting for assistance please have the following information ready: - All messages displayed on the screen; - System version and configuration files. < End of the README >Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.