Windows for Workgroups v3.11
v3.03
Microsoft Windows* for Workgroups 3.11 Installation Notes for Intel's
EtherExpress(TM) PRO/10 LAN Adapter
=====================================================================
Location of Driver: \WFW\EPRO.38_
Novell NetWare* files may be required
------------------------------------
1 If you install Novell NetWare support on this workstation, you need
these Novell NetWare files:
NETWARE.DRV, NETWARE.HLP, NWPOPUP.EXE, VIPX.386, VNETWARE.386
These files are not on the Intel Configuration and Drivers disk. To
obtain these files, do one of the following:
- Download the self-extracting file WINDR2.EXE from the Novell
NetWire forum on CompuServe or Novell's FTP server on the
Internet (ftp.novell.com).
- Call Novell (1-800-NETWARE) to have the files sent to you.
- Contact a Novell NetWare* dealer in your area.
2 To install proper driver support for Windows* for Workgroups and
Novell NetWare on the same workstation, you must set up the
workstation for NetWare first using the DOS ODI client.
SoftSet2 can install the DOS ODI network driver for you. However, you
may need to alter your CONFIG.SYS, AUTOEXEC.BAT, and NET.CFG files so
they comply with your network.
3 After logging into your NetWare file server, start Windows for
Workgroups, then run Network Setup.
Before you start
----------------
You must configure and test the PRO/10 adapter with SOFTSET2.EXE before
adding the adapter to Network Setup in Windows for Workgroups. You must
boot the workstation to DOS, then insert the Intel Configuration and
Drivers disk into drive A. At the DOS prompt type
A:SOFTSET2
1 Select "Automatic Setup" and let SoftSet2 configure the
EtherExpress(TM) PRO/10 adapter to work in your computer. Select
"Change Adapter Configuration" if you want to specify which interrupt
and I/O address the EtherExpress PRO/10 adapter will use.
When SoftSet2 asks for a network frame type, select the frame type
appropriate for your LAN. If you want to add extra frame types, do so
in your NET.CFG file.
2 Select "Test Adapter" from the main menu to test the configuration you
have selected. If the EtherExpress PRO/10 adapter fails diagnostics,
it may not function correctly under Windows for Workgroups.
NOTE: SoftSet2 is a DOS program and will not run in Windows for
Workgroups. You must run SoftSet2 from DOS. If Windows for
Workgroups loads automatically on your computer, you can boot
to DOS by inserting a DOS boot disk into your floppy disk
drive A when rebooting, or you can exit Windows for
Workgroups to get back to DOS.
General Installation
--------------------
1 Start Windows for Workgroups (WFW) with the /N parameter. This starts
WFW without starting any of the networking software. At the DOS
prompt, type
C:\WINDOWS\WIN /N
2 Select the "Network Setup" icon in the Network Group.
3 Click the "Networks" button. Select "Install Microsoft Windows
Network" and click "OK".
<Optional> To add Novell NetWare support to this workstation, click
"Other," then select "Novell NetWare Shell 3.x" if you're using NETX,
or select "Novell NetWare Shell 4.x" if you're using VLMs. Click "OK".
<Optional> To share files and printers on this workstation, click the
"Sharing" button, then click "OK".
4 Click the "Drivers" button.
5 Click the "Add Adapter" button. Select "Unlisted or Updated Network
Adapter" and click "OK".
6 Insert the Intel Configuration and Drivers disk into a drive and for
the path, type:
A:\WFW
7 Select "Intel EtherExpress(TM) PRO/10" adapter from the list and click
"OK".
8 Specify the Interrupt, Base I/O port, and Transceiver type settings.
If you're not sure what they should be, make a selection here and
after WFW installation is complete, run SoftSet2 to make sure they are
correct. If you are using the AUI connector, select the AUI/DIX option
for Transceiver type.
NOTE: If you load Novell NetWare ODI drivers, these settings are
assigned automatically for you.
9 In the Network Drivers window, click "Close".
10 In the Network Setup window, click "OK".
11 In the Microsoft Windows Network Names window, enter a unique User
Name, the name of your new or existing Workgroup, and a unique
Computer Name for your workstation, then click "OK".
12 Choose "Yes To All" when WFW asks if you want to replace the files
currently installed with the versions you are installing now.
13 Insert the WFW disks when WFW asks for the driver update files. If
prompted for the NetWare files, insert the Novell disk containing the
drivers from the Novell file WINDR2.EXE. If prompted for the path of
EPRO.386, insert the Configuration and Drivers disk into a drive and
for the path, type
A:\WFW
If prompted for the path of EPRO.DOS, insert the EtherExpress PRO/10
Configuration and Drivers disk in drive A and type
A:\NDIS
14 When finished updating the files, WFW reports that it modified several
files. Click on "OK".
WFW changes your last drive to P. You may change this setting in your
CONFIG.SYS file.
WFW also alters your NET.CFG file. Check this file to make sure your
frame types load in the correct order for your network.
15 When WFW prompts you to restart your computer for the changes to take
effect, click on "Restart Computer".
Remember to log into your NetWare server before starting WFW.
Hints and Tips
--------------
1 ERROR 58: WHILE LOADING PROTOCOL NUMBER 0...
--------------------------------------------
If WFW fails to detect or initialize the EtherExpress PRO/10
adapter, you get this error message when starting WFW:
THE FOLLOWING ERRORS OCCURRED WHILE LOADING PROTOCOL NUMBER 0: ERROR
58: THE NETWORK HAS RESPONDED INCORRECTLY. YOU MAY NEED TO RECONFIGURE
THE PROTOCOL USING NETWORK SETUP.
Try these steps:
a Verify that the I/O address and interrupt used by the EtherExpress
PRO/10 adapter are not used by any other device (like sound cards,
faxmodems, serial ports, parallel ports, etc.) in your computer.
Look at the documentation or run the setup programs for the other
adapters in your computer to verify which I/O address and
interrupts they are using. Some sound cards use multiple interrupts
and I/O addresses. For example, a typical sound card will use an
I/O address of 220 and IRQ 5 for the sound port, an I/O address of
330 and IRQ 11 for the CD-ROM, and IRQ 2/9 for the MIDI/Joystick
port.
b Verify that the EtherExpress PRO/10 adapter passes all diagnostic
tests by running SOFTSET2.EXE from DOS and selecting "Test
Adapter". If the EtherExpress PRO/10 adapter fails diagnostics, it
will not function correctly under Windows for Workgroups.
If On-Board diagnostics fail, try setting the EtherExpress PRO/10
adapter to a different I/O address, a different interrupt, or
change Force 8 bit operation to "Yes".
If On-Network diagnostics fail, there is likely a cable, connector,
or hub problem. Verify that the cabling you are using is connected
properly and that the cable isn't defective. For more information
on cable specifications, view the TPE or BNC Cabling Specification
readme files on the Configuration and Drivers disk.
Note: "Responder not found" is NOT an error. This message will be
displayed IF YOU ARE NOT RUNNING THE SOFTSET2 RESPONDER ON
ANOTHER MACHINE with an EtherExpress card or if the card
cannot actually communicate with the responder card. If you
don't have a responder running, or if the two cards can't
communicate, the diagnostic will try to send packets back to
itself.
c If you use Novell NetWare, and Windows for Workgroups fails to
detect that the ODI drivers are loaded while running Network Setup,
you will get this error message when starting Windows for
Workgroups. Because Windows for Workgroups was unable to detect
which ODI driver was loaded, it will add the variable "XXXX" to the
NET.CFG and PROTOCOL.INI files where it should have specified
"EPROODI". When this error occurs, you will need to manually edit
the NET.CFG and PROTOCOL.INI that Windows for Workgroups created to
replace all instances of "XXXX" with "EPROODI".
Here are the entries that need to be changed: In the PROTOCOL.INI,
under the section heading [net.cfg], verify the path specified for
your NET.CFG is correct. In the PROTOCOL.INI, change the section
heading [Link Driver XXXX] to [Link Driver EPROODI].
In the PROTOCOL.INI, under the section heading [NWLINK] change both
occurrences of "BINDINGS=XXXX" to "BINDINGS=EPROODI".
In the NET.CFG, change "Link Driver XXXX" to "Link Driver EPROODI"
2 Windows for Workgroups won't load or locks up
---------------------------------------------
After installing the EtherExpress PRO/10 adapter, if WFW won't load
or locks up, make sure the I/O address and interrupt used by the
EtherExpress PRO/10 adapter are not used by any other device (like
sound cards, faxmodems, serial ports, parallel ports, etc.) in your
computer.
If you are using the BNC (coax) connector, you must have a
terminated cable attached to the EtherExpress PRO/10 adapter when
you start Windows for Workgroups. If you don't, Windows for
Workgroups may hang.
3 Adapter passes diagnostics but still does not work with WFW
-----------------------------------------------------------
If the adapter passes diagnostics but still doesn't work with WFW,
there could be a problem with the PROTOCOL.INI file. If you've made
several attempts to configure WFW or had another adapter installed
before the EtherExpress PRO/10 adapter, you may need to restore the
PROTOCOL.INI file to its default settings and reinstall the
EtherExpress PRO/10 adapter driver. Here's how:
a Start WFW with the /N parameter. At the DOS prompt type
C:\WINDOWS\WIN /N
b Click the "Network Setup" icon in the Network group.
c Click the "Networks" button. Select "No Windows Support For
Networks" and click "OK".
d In the Network Setup window, click "OK".
e When WFW reports that it modified several files, click "OK".
f When WFW prompts you to reset your computer for the changes to take
effect, click "Restart Computer".
After the workstation reboots, continue at step 3 of the
"General Installation" section of this document.
4 Can't see other workstations
----------------------------
If Windows for Workgroups loads without error messages, but you
can't see any other computers on your network, verify that the
name of the workgroup is correct and that you are logged on to
the network. Here's how:
a From the Control Panel, click the "Network" icon.
b Verify the workgroup name on your computer is the same as the
workgroup name on a working computer.
c If your Logon Status is "Not Logged On", click on "Log On."
This can also be a cable, connector, or hub problem. Verify that
the cabling you are using is connected properly and is not
defective. Also, try running diagnostics on the adapter\cabling
by selecting "Run Diagnostics on Network" in SoftSet2.
5 Sample PROTOCOL.INI
-------------------
Windows for Workgroups creates the PROTOCOL.INI for you. This is
provided for reference. This is a sample with Microsoft NetBEUI and
IPX/SPX Compatible Transport with NetBIOS.
[network.setup]
version=0x3110
netcard=ms$epro,1,MS$EPRO,3
transport=ms$nwlinknb,NWLINK
transport=ms$ndishlp,MS$NDISHLP
transport=ms$netbeui,NETBEUI
lana0=ms$epro,1,ms$netbeui
lana1=ms$epro,1,ms$nwlinknb
lana2=ms$epro,1,ms$ndishlp
[protman]
DriverName=PROTMAN$
PRIORITY=MS$NDISHLP
[MS$EPRO]
DriverName=EPRO$
INTERRUPT=5
IOADDRESS=0x300
[EPRO]
Adapters=MS$EPRO
[NWLINK]
BINDINGS=MS$EPRO
[MS$NDISHLP]
DriverName=ndishlp$
BINDINGS=MS$EPRO
[NETBEUI]
DriverName=netbeui$
SESSIONS=10
NCBS=12
BINDINGS=MS$EPRO
LANABASE=0
* Third-party trademarks are the property of their respective owners.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.