;********************************************************************
;
; The PCI Ethernet miniport driver oemsetup file
; for WinNT 3.5x, WinNT 4.0
; (NDIS 4.0 driver)
;
;********************************************************************
[Identification]
OptionType = NetAdapter
[PlatformsSupported]
PCI
[Options]
RTL8169
[FileConstants]
UtilityInf = "UTILITY.INF"
subroutineinf = "SUBROUTN.INF"
SoftwareType = "driver"
Exit_Code = 0
NetEventDLL = "%SystemRoot%\System32\netevent.dll;%SystemRoot%\System32\drivers\RTLNIC4.SYS"
IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll"
Manufacturer = "Realtek"
ProductMajorVersion = "03"
ProductMinorVersion = "11"
ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion)
ProductSoftwareName = "RTL8169"
ProductSoftwareImagePath = "%SystemRoot%\System32\drivers\RTLNIC4.SYS"
NetRuleSoftwareType = "RTL8169Sys ndisDriver RTL8169Driver"
NetRuleSoftwareUse = $(SoftwareType)
NetRuleSoftwareBindForm = """RTL8169Sys"" yes no container"
NetRuleSoftwareClass = {"RTL8169Driver basic"}
NetRuleSoftwareBindable = {"RTL8169Driver RTL8169Adapter non exclusive 100"}
ProductHardwareName = "RTL8169"
NetRuleHardwareBindForm = " yes yes container"
ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion"
ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters"
FunctionTitle = "Realtek RTL8169/8110 Family Gigabit Ethernet NIC Setup"
ProductSoftwareDescription = "Realtek RTL8169/8110 Family Gigabit Ethernet NIC Driver"
ProductSoftwareTitle = "Realtek RTL8169/8110 Family Gigabit Ethernet NIC Driver"
ProductHardwareRTL8169Title = "Realtek RTL8169/8110 Family Gigabit Ethernet NIC"
ProductHardwareRTL8169Description = "Realtek RTL8169/8110 Family Gigabit Ethernet NIC"
NetRuleHardwareRTL8169Type = "RTL8169 RTL8169Adapter"
NetRuleHardwareRTL8169Class = {"RTL8169Adapter basic"}
AdapterRTL8169Type = 5 ;; PCI board
RTL8169CFID = 2171146476 ;; 0x816910EC
[GeneralConstants]
from = ""
to = ""
ExitCodeOk = 0
ExitCodeCancel = 1
ExitCodeFatal = 2
KeyNull = ""
MAXIMUM_ALLOWED = 33554432
RegistryErrorIndex = NO_ERROR
KeyProduct = ""
KeyParameters = ""
TRUE = 1
FALSE = 0
NoTitle = 0
ExitState = "Active"
OldVersionExisted = $(FALSE)
DriverPath = $(!STF_NTPATH)\drivers
NT350VersionConstant = "3.50"
NT310VersionConstant = "3.10"
[date]
Now = {} ? $(!LIBHANDLE) GetSystemDate
;
; The [Identify] section is the first section executed by Setup. It
; returns information to Setup about the type of drivers that can
; be installed by this .INF file (in our case, network drivers).
;
[Identify]
read-syms Identification
set Status = STATUS_SUCCESSFUL
set Identifier = $(OptionType)
set Media = #("Source Media Descriptions", 1, 1)
Return $(Status) $(Identifier) $(Media)
;
; If the [Identify] section indicates that the .INF file supports
; the appropriate type of driver, Setup calls the [ReturnOptions]
; section. Setup passes a single parameter to this section,
; indicating the language to be used for dialog strings. This
; section returns information to the Setup program, listing the
; names of any drivers which can be installed by this .INF file.
; It also returns the text strings for each driver to be used in
; the dialog box asking the user to select the driver to install.
;
[ReturnOptions]
;
; Initialize variables to failure state.
;
set Status = STATUS_FAILED
set OptionList = {}
set OptionTextList = {}
;
; See if our language list supports the language specified.
; If a second parameter was passed in, see if it is a supported
; platform.
;
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) in $(LanguageList)
ifstr(i) $($1) == ""
goto returnoptions
endif
set PlatformList = ^(PlatformsSupported, 1)
Ifcontains(i) $($1) in $(PlatformList)
goto returnoptions
else
set Status = STATUS_NOTSUPPORTED
goto finish_ReturnOptions
endif
else
set Status = STATUS_NOLANGUAGE
goto finish_ReturnOptions
endif
;
; If we get here, we are successful, so return the option list.
;
returnoptions = +
set OptionList = ^(Options, 1)
set OptionTextList = ^(OptionsText$($0), 1)
set Status = STATUS_SUCCESSFUL
;
; Exit from this section.
;
finish_ReturnOptions = +
Return $(Status) $(OptionList) $(OptionTextList)
;
; If the [ReturnOptions] section returns successfully, indicating
; the language is supported, Setup displays a dialog box from which
; the user can select a driver to install. Setup then calls the
; [InstallOption] section, with the following parameters:
;
; Language to use
; OptionID to install
; SourceDirectory
; AddCopy (yes/no)
; DoCopy (yes/no)
; DoConfig (yes/no)
;
; ScrDir seems to always be A:\, even when you later install from
; the oemnad#.inf which is copied to the system32 directory.
;
; AddCopy and DoCopy are valid only when NTN_InstallMode = install.
; AddCopy is yes if the files should be added to the copy list.
; DoCopy is yes if CopyFilesInCopyList should be called.
;
; DoConfig is not used for network cards.
;
; This .INF file is automatically copied to the SYSTEM32 directory,
; by WinNT, and renamed so as to have a unique name.
;
[InstallOption]
;;;
;;; Change "Set !G:DebugOutputControl=0" to 1 in NCAPSHEL.INF for debug support.
;;;
;;; set !G:DebugOutputControl=1 ;; Debug output {1=turned on, 0= turned off}
;
; Read input parameters.
;
set Option = $($1)
set SrcDir = $($2)
set AddCopy = $($3)
set DoCopy = $($4)
set DoConfig = $($5)
;
; Check if specified language is supported.
;
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) NOT-IN $(LanguageList)
Return STATUS_NOLANGUAGE
endif
;
; Set up local variables and constant values.
;
set-subst LF = "\n"
read-syms GeneralConstants
read-syms FileConstants
; set NetRuleSoftwareBindable = $($R1)
read-syms DialogConstants$(!STF_LANGUAGE)
ifstr(i) $(!NTN_Origination) == "NCPA"
set Continue = "OK"
endif
read-syms FileConstants$(!STF_LANGUAGE)
;; read-syms FileDependentDlg$(!STF_LANGUAGE)
;; SetHelpFile $(!STF_WINDOWSSYSPATH)"\"$(OptionHelpFile) $(MinHelpId) $(MaxHelpId)
detect date
set-title $(Function$(Option)Title)
set to = Begin
set from = Begin
set CommonStatus = STATUS_SUCCESSFUL
EndWait
;; ;
;; ; Problem was discovered using unattend.txt files for automatic
;; ; installation. It was found that $2 passed into this section does
;; ; not have an appropriate value when using unattend.txt. It was
;; ; found that during manual AND unattended installations, the variable
;; ; STF_SRCDIR_OVERRIDE did contain an appropriate value.
;; ;
;; ifstr(i) $(!STF_SRCDIR_OVERRIDE) != ""
;; set SrcDir = $(!STF_SRCDIR_OVERRIDE)
;; endif
Begin = +
;;
;; Get the Version of Windows NT we are installing on. This will allow us to use the
;; PCI Support that will be included in NT v3.51
;;
set CurrentVersionValue = ""
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows Nt\CurrentVersion" $(!REG_KEY_READ) KeyNt
Ifstr(i) $(KeyNt) != ""
GetRegValue $(KeyNt) "CurrentVersion" CurrentVersionValue
Debug-Output "$(InfFile) $(Option): WinNT CurrentVersion ="$(CurrentVersionValue)
CloseRegKey $(KeyNt)
Endif
ifstr(i) (*($(CurrentVersionValue),4)) == $(NT310VersionConstant) ;; NT v3.10 not supported!
Debug-Output "$(InfFile) $(Option): Configureadapter"
set Error = "Windows NT v3.10 is not support by this product"
goto fatal
endif
; set ActivateDetection = FALSE
;
; NTN_InstallMode
; install - this is a primary or original installation, it
; may be an upgrade
; deinstall - this product and its binaries are to be removed
; from the disk
; configure - this product is to be (re-) configured
; bind - this product's relationships to other products
; have changed and should be reviewed.
;
Ifstr(i) $(!NTN_InstallMode) == deinstall
set StartLabel = removeadapter
else-Ifstr(i) $(!NTN_InstallMode) == Update
set StartLabel = UpgradeSoftware
else-Ifstr(i) $(!NTN_InstallMode) == bind
set StartLabel = bindingadapter
else-Ifstr(i) $(!NTN_InstallMode) == configure
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
set from = end
set to = end
goto nonfatalinfo
else
set StartLabel = configureadapter
endif
else
set StartLabel = installadapter
set OEM_ABANDON_OPTIONS = {}
set OEM_ABANDON_SOFTWARE = FALSE
set OEM_ABANDON_ON = TRUE
endif
;; ;
;; ; HARDWARE_PUT_IN_REGISTRY gets set to true once the hardware
;; ; component is installed. That way if we get an error we know
;; ; to uninstall it. HWList has the path to the hardware that
;; ; is needed by RemoveHardwareComponent.
;; ;
;; ; SOFTWARE_PUT_IN_REGISTRY gets set to true once the software
;; ; component is installed.
;; ;
;; set HARDWARE_PUT_IN_REGISTRY = $(FALSE)
;; set HWList = ""
;; set SOFTWARE_PUT_IN_REGISTRY = $(FALSE)
Debug-Output "$(InfFile) $(Option): =================================================="
Debug-Output "$(InfFile) $(Option): STF_CWDIR is: "$(!STF_CWDIR)
Debug-Output "$(InfFile) $(Option): STF_SRCDIR is: "$(!STF_SRCDIR)
Debug-Output "$(InfFile) $(Option): STF_LANGUAGE is: "$(!STF_LANGUAGE)
Debug-Output "$(InfFile) $(Option): Option is: "$(Option)
Debug-Output "$(InfFile) $(Option): !STF_NCN_InstallMode is:"$(!NTN_InstallMode)
Debug-Output "$(InfFile) $(Option): !STF_NCDETECT is: "$(!STF_NCDETECT)
Debug-Output "$(InfFile) $(Option): !STF_NCOPTION is: "$(!STF_NCOPTION)
Debug-Output "$(InfFile) $(Option): !STF_NCDETCARD is: "$(!STF_NCDETCARD)
Debug-Output "$(InfFile) $(Option): !STF_NCDETINFO is: "$(!STF_NCDETINFO)
Debug-Output "$(InfFile) $(Option): !STF_GUI_UNATTENDED is: "$(!STF_GUI_UNATTENDED)
Debug-Output "$(InfFile) $(Option): !STF_BusType is $(!STF_BUSTYPE)" ;; Primary Bus
Debug-Output "$(InfFile) $(Option): !STF_BusTypeList is $(!STF_BUSTYPELIST)" ;; All Buses
Debug-Output "$(InfFile) $(Option): =================================================="
Set EtherID = ""
Set NetworkAddress = "000000000000"
set from = $(fatal)
set to = $(fatal)
goto $(StartLabel)
;------------------------------------------------------------------------
; InstallMode = install
; Came here straight from figuring out which platform we are on.
; Option, SrcDir, AddCopy, DoCopy, and DoConfig are valid.
;
installadapter = +
install "Install-Hlp"
Debug-Output "$(InfFile) $(Option): Installadapter"
;
; Get open handle KeyProduct.
; Returns an empty string if key does not exist.
;
; NTN_RegBase appears empty on the installation of the first card.
; KeyProduct will be KeyNull on the installation of the first card.
;
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
CloseRegKey $(KeyProduct)
ifstr(i) !(NTN_RegBase) == $(ProductKeyName)
; Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+
; $(ProductVersion)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error: cannot get an error string."
goto ShellCodeError
endif
goto end
else
; Shell $(UtilityInf), CardExistedDlg
; ifint $($ShellCode) != $(!SHELL_CODE_OK)
; Debug-Output "ShellCode error: cannot get an error string."
; goto ShellCodeError
; endif
; ifstr(i) $($R1) != "OK"
; set CommonStatus = STATUS_USERCANCEL
; goto end
; endif
set OldVersionExisted = $(TRUE)
endif
Endif
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) NO
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
; Set SrcDir = $($R1)
; Set SrcDir = "A:\DRIVER"
; Goto adapteroptions
Goto installproduct
configureadapter = +
Debug-Output "$(InfFile) $(Option): Configureadapter"
Ifstr(i) $(KeyProduct) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) == $(KeyNull)
Set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
Goto fatalregistry
Endif
Endif
Shell $(UtilityInf) FindService, $(KeyProduct)
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Endif
Ifstr(i) $($R0) != NO_ERROR
Goto fatalregistry
endif
set KeyParameters = $($R2)
CloseRegKey $($R1)
Ifstr $(KeyParameters) == $(KeyNull)
set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
goto fatalregistry
endif
set OldVersionExisted = $(TRUE)
set ValueName = ""
set ValueData = ""
set ValueStr = ""
set ValueList = {}
EnumRegValue $(KeyParameters) ValueList
ForListDo $(ValueList)
set ValueItem = $($)
set ValueName = *($(ValueItem),1)
set ValueData = *($(ValueItem),4)
Ifstr(i) $(ValueName) == "DuplexMode"
set DuplexModeIndex = $(ValueData)
else-ifstr(i) $(ValueName) == "EtherID"
set EtherID = $(ValueData)
else-ifstr(i) $(ValueName) == "NetworkAddress"
set NetworkAddress = $(ValueData)
else-ifstr(i) $(ValueName) == "EarlyTxThreshold" ;luke add3 show preseting vlue
set EarlyTxThreshold = $(ValueData)
endif
EndForListDo
set DuplexModeValue = *($(DuplexModeList), ~($(DuplexModeValues),$(DuplexModeIndex)))
ifstr(i) $(DuplexModeValue) == ""
set DuplexModeValue = *($(DuplexModeList), 1)
endif
;;; set Error = "Cannot configure the software component"
;;; goto fatal
adapteroptions = +
Debug-Output "$(InfFile) $(Option): Adapteroptions"
set from = adapteroptions
read-syms FileDependentDlg$(!STF_LANGUAGE)
;SetHelpFile $(!STF_WINDOWSSYSPATH)"\"$(OptionHelpFile) $(MinHelpId) $(MaxHelpId) $(Help$(Option)Id)
SetHelpFile $(!STF_WINDOWSSYSPATH)"\"r8169hlp.hlp 10 20 10
ui start "InputDlg"
; ifstr(i) $(DLGEVENT) == "CONTINUE"
; set DuplexModeIndex = $(Combo1Out)
; ui pop 1
; else-ifstr(i) $(DLGEVENT) == "BACK"
; set CommonStatus = STATUS_USERCANCEL
; ui pop 1
; goto end
; else
; ui pop 1
; goto end
; endif
ifstr(i) $(DLGEVENT) == "CONTINUE"
set DuplexModeIndex = $(Combo1Out)
ui pop 1
else-ifstr(i) $(DLGEVENT) == "BACK"
set CommonStatus = STATUS_USERCANCEL
ui pop 1
goto end
else
ui pop 1
goto end
endif
set DuplexModeValue = *($(DuplexModeValues), ~($(DuplexModeList),$(DuplexModeIndex)))
set EtherID = ""
;;;;;;;;;;;;;;;;;;Ether ID;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
read-syms NetworkAddressDlg$(!STF_LANGUAGE)
ui start "InputDlg"
ifstr(i) $(DLGEVENT) == "CONTINUE"
;;set EtherID = $(EditTextOut)
set NetworkAddress = $(EditTextOut)
ui pop 1
else-ifstr(i) $(DLGEVENT) == "EXIT"
ui pop 1
else
ui pop 1
goto end
endif
set EarlyTxThreshold = "63"
;;;;;;;;;;;;;;;;;;Ether ID;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
read-syms EarlyTxThresholdDlg$(!STF_LANGUAGE)
ui start "InputDlg"
ifstr(i) $(DLGEVENT) == "CONTINUE"
set EarlyTxThreshold = $(EditTextOut)
ui pop 1
else-ifstr(i) $(DLGEVENT) == "EXIT"
ui pop 1
else
ui pop 1
goto end
endif
ifstr(i) $(!NTN_InstallMode) == configure
goto updateparameters
endif
;; ifstr(i) $(!NTN_InstallMode) == configure
;; goto updateparameters
;; endif
installproduct =+
Debug-Output "$(InfFile) $(Option): installproduct"
StartWait
set AdapterList = $($R1)
ifint $(OldVersionExisted) == $(FALSE)
Ifstr(i) $(DoCopy) == "YES"
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) NO
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
Set SrcDir = $($R1)
Endif
install "Install-Option"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
endif
endif
;
; Check to see if the Product Software key exists already in the system service keys
; before we try to add the software component.
;
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_ServiceBase)"\"$(ProductHardwareName) $(!REG_KEY_READ) KeyNt
CloseRegKey $(KeyNt)
Ifstr(i) $(KeyNt) == ""
Debug-Output "$(InfFile) $(Option): AddSoftwareComponent"
Debug-Output "$(InfFile) $(Option): --> $(Manufacturer)"
Debug-Output "$(InfFile) $(Option): --> $(ProductSoftwareName)"
Debug-Output "$(InfFile) $(Option): --> $(ProductSoftwareTitle)"
Debug-Output "$(InfFile) $(Option): --> $(STF_CONTEXTINFNAME)"
Debug-Output "$(InfFile) $(Option): --> $(ProductSoftwareImagePath)"
Debug-Output "$(InfFile) $(Option): --> $(NetEventDLL)"
Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), +
$(ProductSoftwareName), +
$(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), +
$(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+
$(NetEventDLL)
Set OEM_ABANDON_SOFTWARE = TRUE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
CloseRegKey $($R4)
CloseRegKey $($R5)
goto fatalregistry
endif
Set SoftProductKey = $($R1)
Set SoftNetRuleKey = $($R2)
Set SoftServiceKey = $($R3)
Set SoftParameterKey = $($R4)
Set SoftLinkageKey = $($R5)
set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+
{MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+
{MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+
{Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(SoftProductKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftParameterKey)
CloseRegKey $(SoftLinkageKey)
goto fatalregistry
endif
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+
{use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, +
{bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, +
{bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareBindable)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(SoftNetRuleKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftParameterKey)
CloseRegKey $(SoftLinkageKey)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
goto fatalregistry
endif
endif ;; Does Services\RTL8169 exist?
set NTDetected = $(FALSE)
Debug-Output "$(InfFile) $(Option): About to look for RTL8169 PCI Cards"
;;
;; we must be installing a PCI card.
;;
;; Note: If we are are on WinNT v3.51 and above, we have PCI detection support
;; and are able to setup the adapter without user intervention. Otherwise, we can
;; only do one card at a time.
;;
set TargetVersion = *($(CurrentVersionValue),4)
Debug-Output "$(InfFile) $(Option): Current Version:"$(TargetVersion)
ifstr $(TargetVersion) == $(NT350VersionConstant) ;; We need to ask on v3.50
Debug-Output "Running on WindowsNT 3.50"
set Version350 = $(TRUE)
else
Debug-Output "Running on WindowsNT 3.51"
set Version350 = $(FALSE)
endif
ifint $(Version350) == $(TRUE)
Debug-Output "Running on WindowsNT v3.50, Not using PCI Detection!!!"
ifstr $(!STF_GUI_UNATTENDED) == "YES"
Debug-Output "$(InfFile) $(Option): Running in GUI unattended mode"
ifstr(i) $(!AutoNetInterfaceType) != ""
set BusInterfaceType = $(!AutoNetInterfaceType)
else
set BusInterfaceType = 5
endif
ifstr(i) $(!AutoNetBusNumber) != ""
set BusNumber = $(!AutoNetBusNumber)
else
set BusNumber = 0
endif
set NTDetected = $(FALSE)
set AdapterList = $(Option) ;; 1 Item to install
Debug-Output "$(InfFile) $(Option): BusInterfaceType = $(BusInterfaceType)"
Debug-Output "$(InfFile) $(Option): BusNumber = $(BusNumber)"
else
Debug-Output "$(InfFile) $(Option): Running 3.50 Bus Dialog"
set BusInterfaceType = 5
set BusNumber = 0
set NTDetected = $(FALSE)
Shell $(UtilityInf),GetBusTypeDialog,$(ProductHardware$(Option)Description) $(BusInterfaceType) $(BusNumber)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
set BusInterfaceType = $($R1)
set BusNumber = $($R2)
set AdapterList = $(Option) ;; 1 Item to install
Debug-Output "$(InfFile) $(Option): BusInterfaceType = $(BusInterfaceType)"
Debug-Output "$(InfFile) $(Option): BusNumber = $(BusNumber)"
endif
else
Debug-Output "$(InfFile) $(Option): Running 3.51 using PCI Dectection"
;;
;; v3.51 has PCI detection code built in.
;;
;;set BusInterfaceType = 5
;;set BusNumber = 0
;; Shell $(UtilityInf),GetBusTypeDialog,$(ProductHardware$(Option)Description) $(BusInterfaceType) $(BusNumber)
set NTDetected = $(TRUE)
set VendorID = 4332 ;; 0x10EC is REALTEK's Vendor ID
set DeviceID = 33129 ;; 0x8169 is RTL8169's Device ID
;;set-div CFID = $($(Option)CFID) 1
Debug-Output "$(InfFile) $(Option): VendorID = $(VendorID)"
Debug-Output "$(InfFile) $(Option): DeviceID = $(DeviceID)"
;;Shell $(UtilityInf), GetPCIInformation, $(VendorID) $(CFID)
Shell $(UtilityInf), GetPCIInformation, $(VendorID) $(DeviceID)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R0) == {}
set Error = $(CANNOT_FIND_ANY_CARD)
set CommonStatus = USER_CANCEL
set from = end
goto nonfatal
endif
set AdapterList = $($R0)
endif ;;; NT v3.50
endif ;;; Looking for PCI cards in Option.
; "AdapterList" has the list of currently installed adatpers in the system!
;
Debug-Output "$(InfFile) $(Option): Adapterlist = $(AdatperList)"
ForListDo $(AdapterList)
Set InstallCard = "YES"
ifint $(NTDetected) == $(TRUE)
set DetectedBusNum = *($($),1)
set DetectedSlotNum = *($($),2)
Debug-Output "$(InfFile) $(Option): DetectedBusNumber = $(DetectedBusNum)"
Debug-Output "$(InfFile) $(Option): DetectedSlotNum = $(DetectedSlotNum)"
Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(DetectedBusNum), +
$(DetectedSlotNum), $(ProductHardware$(Option)Description), $(ProductHardwareName)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr $($R0) != "NO_ERROR"
set Error = $($R0)
goto fatal
endif
ifstr(i) $($R1) == "YES"
set InstallCard = "NO" ;; Don't want to re-install, it's there already
endif
endif
;;
;; Are we installing the card?
;;
ifstr(i) $(InstallCard) == "NO"
Debug-Output "$(InfFile) $(Option): Card Already at $(DetectedBusNum):$(DetectedSlotNum) already installed!"
set Error = "An adapter at $(DetectedBusNum):$(DetectedSlotNum) is already installed!"
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
else
Debug-Output "$(InfFile) $(Option): Installing Card at $(DetectedBusNum):$(DetectedSlotNum)!"
Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)
ifint $($R4) != -1
Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
endif
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
goto fatalregistry
endif
set EarlyTxThreshold = 63
set DuplexModeValue = *($(DuplexModeValues), ~($(DuplexModeList),$(DuplexModeIndex)))
ifstr(i) $(!STF_GUI_UNATTENDED) == "YES" ; luke add1 unattend
Debug-Output "$(InfFile) $(Option): Running in GUI unattended mode"
ifstr(i) $(!AutoNetInterfaceType) != ""
set BusInterfaceType = $(!AutoNetInterfaceType)
else
set BusInterfaceType = 5
endif
ifstr(i) $(!AutoNetBusNumber) != ""
set BusNumber = $(!AutoNetBusNumber)
else
set BusNumber = 0
endif
goto skiplaa1
endif
read-syms FileDependentDlg$(!STF_LANGUAGE)
;SetHelpFile $(!STF_WINDOWSSYSPATH)"\"$(OptionHelpFile) $(MinHelpId) $(MaxHelpId) $(Help$(Option)Id)
SetHelpFile $(!STF_WINDOWSSYSPATH)"\"r8169hlp.hlp 10 20 10
ui start "InputDlg"
ifstr(i) $(DLGEVENT) == "CONTINUE"
set DuplexModeIndex = $(Combo1Out)
ui pop 1
else-ifstr(i) $(DLGEVENT) == "BACK"
set CommonStatus = STATUS_USERCANCEL
ui pop 1
goto end
else
ui pop 1
goto end
endif
set DuplexModeValue = *($(DuplexModeValues), ~($(DuplexModeList),$(DuplexModeIndex)))
set EtherID = ""
;;;;;;;;;;;;;;;;;;Ether ID;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
read-syms NetworkAddressDlg$(!STF_LANGUAGE)
ui start "InputDlg"
ifstr(i) $(DLGEVENT) == "CONTINUE"
;;set EtherID = $(EditTextOut)
set NetworkAddress = $(EditTextOut)
ui pop 1
else-ifstr(i) $(DLGEVENT) == "EXIT"
ui pop 1
else
ui pop 1
goto end
endif
read-syms EarlyTxThresholdDlg$(!STF_LANGUAGE)
ui start "InputDlg"
ifstr(i) $(DLGEVENT) == "CONTINUE"
set EarlyTxThreshold = $(EditTextOut)
ui pop 1
else-ifstr(i) $(DLGEVENT) == "EXIT"
ui pop 1
else
ui pop 1
goto end
endif
skiplaa1 =+
Set HardNetCardKey = $($R1)
Set HardNetRuleKey = $($R2)
Set HardParameterKey = $($R3)
set AdapterNumber = $($R4)
set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+
{Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+
{ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(HardNetCardKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
;
; PCI
;
set BusTypeNum = 5
set BusMaster = "YES"
set Bus = "PCI"
ifstr(i) $(Option) == "RTL8169"
set CardType = 2
else
set CardType = 0
endif
;;
;; If we used the OS to dected the card, then we already know bus and slot information.
;;
ifint $(NTDetected) == $(TRUE)
set BusNumber = $(DetectedBusNum)
set SlotNum = $(DetectedSlotNum)
set BusInterfaceType = $(BusTypeNum)
;
; Note: we need to record SlotNumber too so that we can use the
; "IsNetCardAlreadyInstalled" routine
;
Set NewValueList = {+
{BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNumber)},+
{Slot,$(NoTitle),$(!REG_VT_DWORD),$(SlotNum)}+
}
Debug-Output "$(InfFile) $(Option): Set HardwareParameterKey = $(NewValueList)"
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
Set NewValueList = { {SlotNumber,$(NoTitle),$(!REG_VT_DWORD),$(SlotNum)} }
Debug-Output "$(InfFile) $(Option): Set HardwareParameterKey = $(NewValueList)"
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
else
Set NewValueList = {+
{BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNumber)},+
}
Debug-Output "$(InfFile) $(Option): Set HardwareParameterKey = $(NewValueList)"
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
endif
Set NewValueList = {+
{BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusInterfaceType)},+
{CardType,$(NoTitle),$(!REG_VT_DWORD),$(CardType)},+
{MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+
{AdapterCFID,$(NoTitle),$(!REG_VT_DWORD),$($(Option)CFID)},+
}
Debug-Output "$(InfFile) $(Option): Set HardwareParameterKey = $(NewValueList)"
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set NewValueList = {{DuplexMode, $(NoTitle),$(!REG_VT_DWORD),$(DuplexModeValue)},+
{TxMaxDMABurst, $(NoTitle),$(!REG_VT_DWORD),6},+
{RxMaxDMABurst, $(NoTitle),$(!REG_VT_DWORD),7},+
{EarlyRxThreshold,$(NoTitle),$(!REG_VT_DWORD),7},+
{TxInterFrameGap, $(NoTitle),$(!REG_VT_DWORD),3},+
{NumTxDesc, $(NoTitle),$(!REG_VT_DWORD),128},+
{NumRxDesc, $(NoTitle),$(!REG_VT_DWORD),128},+
{NumTcb, $(NoTitle),$(!REG_VT_DWORD),96},+
{NumRfd, $(NoTitle),$(!REG_VT_DWORD),192},+
{NetworkAddress, $(NoTitle),$(!REG_VT_SZ), $(NetworkAddress)},+
{EarlyTxThreshold,$(NoTitle),$(!REG_VT_DWORD),$(EarlyTxThreshold)}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifstr(i) $(!STF_GUI_UNATTENDED) == "YES" ; luke add2 Input parameter
Shell $(UtilityInf),AddDefaultNetCardParameters,$(HardParameterKey)
endif
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardware$(Option)Type)},+
{bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardware$(Option)Class)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Debug-Output "$(InfFile) $(Option): HardwareRuleKey = $(NewValueList)"
Shell $(UtilityInf), AddValueList, $(HardNetRuleKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
CloseRegKey $(HardNetCardKey)
CloseRegKey $(HardNetRuleKey)
CloseRegKey $(HardParameterKey)
endif
EndForListDo
EndWait
goto successful
updateparameters =+
Debug-Output "$(InfFile) $(Option): Updateparameters"
set HardParameterKey = $($R3)
set NewValueList = {{DuplexMode,$(NoTitle),$(!REG_VT_DWORD),$(DuplexModeValue)},+
{TxMaxDMABurst, $(NoTitle),$(!REG_VT_DWORD),6},+
{RxMaxDMABurst, $(NoTitle),$(!REG_VT_DWORD),7},+
{EarlyRxThreshold,$(NoTitle),$(!REG_VT_DWORD),7},+
{TxInterFrameGap, $(NoTitle),$(!REG_VT_DWORD),3},+
{NumTxDesc, $(NoTitle),$(!REG_VT_DWORD),128},+
{NumRxDesc, $(NoTitle),$(!REG_VT_DWORD),128},+
{NumTcb, $(NoTitle),$(!REG_VT_DWORD),96},+
{NumRfd, $(NoTitle),$(!REG_VT_DWORD),192},+
{NetworkAddress,$(NoTitle),$(!REG_VT_SZ),$(NetworkAddress)},+
{EarlyTxThreshold,$(NoTitle),$(!REG_VT_DWORD),$(EarlyTxThreshold)}}
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
ifstr(i) $(!STF_GUI_UNATTENDED) == "YES" ; luke add2 Input parameter
Shell $(UtilityInf),AddDefaultNetCardParameters,$(HardParameterKey)
endif
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
CloseRegKey $(KeyParameters)
goto successful
bindingadapter =+
Debug-Output "$(InfFile) $(Option): bindingadapter"
set Error = "Binding: Sorry, not yet implemented."
goto fatal
removeadapter = +
Debug-Output "$(InfFile) $(Option): removeadapter"
Debug-Output "$(InfFile) $(Option): ----> $(ProductKeyName), $(!NTN_RegBase)"
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
else
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $(!NTN_RegBase)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
UpgradeSoftware = +
Debug-Output "$(InfFile) $(Option): UpdateSoftware"
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set !UG_Filename = $($R0)
install "Install-Update"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
goto fatal
endif
SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)}
SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)}
CloseRegKey $(KeyProduct)
else
goto fatalregistry
endif
goto end
successful = +
Debug-Output "$(InfFile) $(Option): Successful"
goto end
abandon = +
Debug-Output "$(InfFile) $(Option): Abandon"
ForListDo $(OEM_ABANDON_OPTIONS)
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $($)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
EndForListDo
Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), FALSE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
warning = +
Debug-Output "$(InfFile) $(Option): warning"
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(to)
else-ifstr(i) $($R1) == "CANCEL"
goto $(from)
else
goto "end"
endif
nonfatalinfo = +
Debug-Output "$(InfFile) $(Option): nonfatalinfo"
Set CommonStatus = STATUS_USERCANCEL
Set Severity = STATUS
goto nonfatalmsg
nonfatal = +
Debug-Output "$(InfFile) $(Option): nonfatal"
Set Severity = NONFATAL
goto nonfatalmsg
nonfatalmsg = +
Debug-Output "$(InfFile) $(Option): nonfatalmsg"
ifstr(i) $(Error) == ""
Set Severity = NONFATAL
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(from)
else
; goto "end"
goto "RemoveAdapter"
endif
fatalregistry = +
Debug-Output "$(InfFile) $(Option): fatalregistry"
Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
fatal = +
Debug-Output "$(InfFile) $(Option): fatal"
ifstr(i) $(Error) == ""
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
goto setfailed
ShellCodeError = +
Debug-Output "$(InfFile) $(Option): ShellCodeError"
set DlgType = "MessageBox"
set STF_MB_TITLE = $(ShellCodeErrorTitle)
set STF_MB_TEXT = $(ShellCodeErrorText)
set STF_MB_TYPE = 1
set STF_MB_ICON = 3
set STF_MB_DEF = 1
ui start "Error Message"
goto setfailed
setfailed = +
Debug-Output "$(InfFile) $(Option): Setfailed"
set CommonStatus = STATUS_FAILED
ifstr(i) $(OEM_ABANDON_ON) == TRUE
set OEM_ABANDON_ON = FALSE
goto abandon
endif
goto end
end = +
goto term
term = +
Return $(CommonStatus)
[Install-Option]
set STF_VITAL = ""
ifstr(i) $(AddCopy) == "YES"
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
endif
ifstr(i) $(DoCopy) == "YES"
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
endif
Exit
[Install-Hlp]
set STF_VITAL = ""
AddSectionFilesToCopyList Files-Hlp $(SrcDir) $(!STF_WINDOWSSYSPATH)
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
Exit
[Install-Update]
set STF_VITAL = ""
set STF_OVERWRITE = "VERIFYSOURCEOLDER"
AddSectionFilesToCopyList Files-Hlp $(SrcDir) $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
exit
[Source Media Descriptions]
1 = "Realtek RTL8169/8110 Family Gigabit Ethernet NIC OEM Driver Disk"
; from disk a:\ or b:\
[ProductType]
STF_PRODUCT = Winnt
STF_PLATFORM = I386
[Files-Inf]
1, oemsetup.inf, SIZE=1000, RENAME=$(!UG_Filename)
[Files-Hlp]
1, R8169HLP.HLP , SIZE=10000
;
; Driver files
;
[Files-RTL8169]
1,RTLNIC4.SYS , SIZE=50000
[LanguagesSupported]
ENG
[OptionsTextENG]
RTL8169 = "Realtek RTL8169/8110 Family Gigabit Ethernet NIC"
[FileConstantsENG]
ProCaption = "Windows NT Setup"
ProCancel = "Cancel"
ProCancelMsg = "Windows NT Networking is not correctly installed. "+
"Are you sure you want to cancel copying files?"
ProCancelCap = "Network Setup Message"
ProText1 = "Copying:"
ProText2 = "To:"
DuplexModeList = ^(DuplexModeDlg, 1)
DuplexModeValues = ^(DuplexModeDlg, 2)
NoList = ^(NoChoices, 1)
NoValues = ^(NoChoices, 2)
ShellCodeErrorTitle = "Error: "$(Function$(Option)Title)
ShellCodeErrorText = "Shell Code Error."
CANNOT_FIND_ANY_CARD = "Network card is not present in the system"
[DialogConstantsENG]
Help = "&Help"
Exit = "Cancel"
OK = "OK"
HelpContext = ""
Continue = "Continue"
Cancel = "Cancel"
[FileDependentDlgENG]
DlgText = "Choose the proper Link Speed/Duplex Mode from the list."$(!LF)+
" "
Combo1Label = "Speed/Duplex Mode"
DlgTemplate = "ADAP_PROTO_COMBO"
DlgType = "Combination"
;Caption = $(Function$(Option)Title)
Caption = "Speed/Duplex mode "
Combo1List = $(DuplexModeList)
Combo1Out = $(DuplexModeValue)
ComboListItemsIn = {Combo1List}
ComboListItemsOut = {Combo1Out}
EditTextLim = ""
CBOptionsGreyed = {}
;MinHelpId = 10
;MaxHelpId = 1130
;HelpContext = $(Help$(Option)Id)
HelpContext = 10
[DuplexModeDlg]
; DuplexMode_0 = "(0) DEFAULT ", 0
DuplexMode_1 = "(1) AUTO ", 1
DuplexMode_2 = "(2) 10 Half Duplex", 2
DuplexMode_3 = "(3) 10 Full Duplex", 3
DuplexMode_4 = "(4) 100 Half Duplex", 4
DuplexMode_5 = "(5) 100 Full Duplex", 5
DuplexMode_6 = "(6) 1000 Full Duplex", 6
[NetworkAddressDlgENG]
Caption = "Input Network Address"
DlgText = "Please input Network Address: "$(!LF)+
"For example:"$(!LF)+
" Ethernet ID: 020102A3B4C5"$(!LF)$(!LF)+
"(This option is only required when you need to use"+
"some networking applications which need software"+
"programmable Network Address)"
Edit1Label = "&Network Address :"
Continue = "&OK"
Exit = "&Skip"
Help = "&Help"
DlgType = "Edit"
DlgTemplate = "QUERY_COMPUTER_NAME"
EditTextLim = 12
EditTextIn = $(NetworkAddress)
EditFocus = "ALL"
[EarlyTxThresholdDlgENG]
Caption = "Input Tx Early Threshold"
DlgText = "Please input Early Tx Threshold: "$(!LF)+
"The value range from 0 to 0x3f in heximal"
Edit1Label = "&EarlyTxThreshold:"
Continue = "&OK"
Exit = "&Skip"
Help = "&Help"
DlgType = "Edit"
DlgTemplate = "QUERY_COMPUTER_NAME"
EditTextLim = 2
EditTextIn = $(EarlyTxThreshold)
EditFocus = "ALL"
;
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.