Install LAN Adapter Driver for IBM Lan Server and Comm. Manager Install the driver for IBM LAN SERVER 4.0 . In the OS/2 Desktop group, double-click on the MPTS icon. . Click on the <Configure> button. . Select the "LAN adapters and protocols" option. . Click on the <Configure> button. . Select the "Other adapters ..." option. . Specify the path where the driver files reside. . Click on the <OK> button. . Select " GFC2204 ...", and then click on the Add button. . Select "IBM OS/2 NETBIOS", and then click on the Add button. . Select "IBM IEEE 802.2", and then click on the Add button. . Click OK. . Click Close. . Click Exit. . Reboot your system. Install the driver for IBM LAN SERVER 3.0 . Install IBM OS/2 into your system, if not yet installed. . Insert the OS/2 Installation Disk in Drive A and boot from that drive. Then, install OS/2. . Insert the NTS/2 Adapter & Protocol Support Disk in Drive B. Then, execute the LAPs program. . Select "Install", and then specify the target drive. . Select "Install" again and insert your driver diskette in Drive A. A:\<PATH>\ Where PATH is the driver directory. or C:\<PATH>\ (if install program specify) . Select "Configure". . Select " GFC2204 ...", and then click on the Add button. . Select "IBM OS/2 NETBIOS", and then click on the Add button. . Select "IEEE 802.2", and then click on the Add button. . Click OK. . Click Exit. . Click Continue. . Reboot your system. Your CONFIG.SYS and PROTOCOL.INI files should reflect your card setup: \CONFIG.SYS : : Device=d:\IBMCOM\MACS\GF2204.OS2 : \IBMCOM\PROTOCOL.INI : [ETHPCII_NIF] Drivername = GF2204$ . Install the LAN Server or Requester program. For information, please refer to your IBM LAN Server "Planning and Installation" manual. Install the NDIS driver for IBM LAN SERVER 2.0 . Assuming that OS/2 2.0 is correctly installed and working properly, install the LAN SERVER. At this point, no network adapters must be installed in the computer. . Install LAN SERVER according to the IBM installation procedure. When prompted for the adapter, select any of the adapters LAN SERVER supports. For example, "Western Digital EtherCard PLUS ...". Then, continue with the LAN SERVER installation. . After successfully installing LAN SERVER, shut down OS/2 for system configuration. Do not install any network adapters yet. The OS/2 system will boot up and bring up the LAN SERVER services. The system will then display error messages since the network adapter you selected is not installed. Ignore these messages and continue with the OS/2 booting procedure. . Insert the driver diskette in Drive A and copy the following files: COPY GF2204.OS2 to C:\IBMCOM\MACS COPY GF2204.NIF to C:\IBMCOM\MACS\GF2204.NIF . In the OS/2 Desktop group, run the OS/2 system editor. You need to modify the following files: C:\CONFIG.SYS C:\IBMCOM\PROTOCOL.INI CONFIG.SYS Modifications: DEVICE=C:\IBMCOM\MACS\MACWD.OS2 to DEVICE=C:\IBMCOM\MACS\GF2204.OS2 PROTOCOL.INI Modifications: - Under the [IBMLXCFG] section, add the following line: GF2204_nif = GF2204.nif - Under the [NETBEUI_nif] section, change the following line: Bindings = MACWDMC_nif to Bindings = GF2204_nif - Under the MAC SECTION definitions, add the following section: [GF2204_nif] DriverName = GF2204$ . After modifying the two files above, shut down OS/2, and turn the computer off. . Install the GF2204. . Turn on the system to start OS/2. After starting OS/2, LAN SERVER services can now successfully start without causing any errors. Install the NDIS driver for IBM Communication Manager 1.0 . Install IBM Communication Manager . Copy the GF2204.OS2 and GF2204.NIF files in the driver diskette to your C:\IBMCOM\MACS directory. . Select the PCI Ethernet Adapter and choose the appropriate protocols. . Check that the CONFIG.SYS file includes the following line: DEVICE = C:\IBMCOM\MACS\GF2204.OS2 . Shut down your OS/2 system, and then reboot your PC.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.