Installation Instructions for Micro Firmware BIOS Upgrade Updates ================================================================= NOTE: Use of these files is governed by the License Agreement contained in the file LICENSE.TXT, included with this distribution. This BIOS Update file will update prior revisions of Micro Firmware's M4HS45G BIOS Upgrade to M4HS45G version 4.05.17. In order to install this update, the M4HS45G BIOS must already be resident on your PC. You can confirm this by booting your PC and watching for the Micro Firmware BIOS part number which will appear on the boot screen. DO NOT ATTEMPT TO INSTALL THIS UPDATE IF YOU DO NOT SEE THE "M4HS45G" PART NUMBER ON THE BOOT SCREEN. You may wish to obtain a copy of the latest system-specific supplemental manual, which is available on our Web site in Adobe Acrobat PDF format. You can use Acrobat reader 3.0 or later to view and print this document. The documentation is on the same page as the update files, at this URL: http://www.firmware.com/support/updates/ You may find additional information pertaining this BIOS upgrade in the technical documents section on our webstie: http://www.firmware.com/support/bios/ BEFORE INSTALLATION =================== Copy the files from this update distribution onto a blank diskette. Run Setup, and make a note of your existing configuration. Pay particular attention to hard drive settings and the settings for the onboard serial and parallel ports. Most settings are retained, but checking your existing configuration is a good precaution in the unlikely event that the flash installation is interrupted for any reason. Be sure that your data is backed up. This is a normal, everyday rule of thumb that everyone should adhere to. Installing the new BIOS revision in and of itself should not affect the data on your hard drive(s) - however, it is especially important to have a back up of any valuable data any time you make any changes to your PC configuration. In some cases our revision updates may be different enough from the revision currently installed that the operating system may not be happy with the change. Windows 95/98 may need to reboot a few times to adjust to the changes or in some unusual cases it may be necessary to reinstall everything on a blank drive. INSTALLATION INSTRUCTIONS ========================= 1. Boot from clean DOS boot disk (such as WIN95/98 Startup Disk). 2. Insert the diskette containing the BIOS update files. 3. Type INSTALL NORECOVER to run the Flash BIOS installation program. The NORECOVER parameter allows the INSTALL program to skip the step of creating a recovery disk. 4. The first thing the installation program will do is examine your system to determine the current system settings. This allows the installation program to preserve many system setup options under the new BIOS. This will take a few moments. 5. Then the installation program will load the BIOS image from disk into RAM. A window will appear showing the progress. This should take just a few seconds. The Flash ROM will then be reprogrammed with the new BIOS. Once the programming is complete, the system will reboot with your new BIOS installed. 6. It is recommended to enter CMOS setup before allowing the system to boot to the hard drive so that you can verify that the hard drive settings are the same as before. It is also be recommended to verify that other CMOS settings are set the same as before. Refer to the system-specific supplemental manual for more details. Questions or problems? Contact Micro Firmware Technical Support at 405-321-8333, or via email at support@firmware.com. rev 09/30/99 TLSDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.