README.TXT Driver File Contents (hawk.zip)


               CardBus Fast Ethernet PC Card Packet Driver
                        Installation Overview

  Contents
  --------
    .Introduction
    .User's Guide
    .Support Options


  Introduction
  ------------
    Packet drivers are general drivers used by many operating systems,
    especially TCP/IP software packages.  If the network system that is
    installed specifically mentions support for packet drivers, then
    it is likely that it will be able to the provided packet driver
    without problems.

    The most important thing to remember when installing packet drivers
    is the software interrupt vector.  The default interrupt vector for
    the packet drivers is 0x62 hexadecimal.  Most network operating
    system supporting packet drivers will try to automatically search for
    packet drivers already loaded in the computer's memory.  However,
    some packages will require a provided interrupt vector for the packet
    driver.  Furthermore, some packages can only work with certain
    interrupt vectors. which require a software interrupt vector parameter
    when loading.  Please see the section at the end of this document for
    description on packet driver parameters.

    Since the card are software configurable, the packet driver will
    automatically detect the hardware parameters. If the packet driver can
    properly read the adapter's MAC address during loading, then the hardware
    is normally working properly.


  User's Guide
  ------------

    Two methods available to install Packet driver

    Method 1.
        In your CONFIG.SYS file, include the DEVICE command.
        Format:
            DEVICE = CB102PD.SYS [/option] <packet_int_no>


    Method 2.
        Install Packet driver by typing CB102PD at the DOS command prompt.
        Format:

            CB102PD.COM [/option] <packet_int_no>


  Support Options
  ---------------

    Parameters and Options    Description
    ----------------------  --------------------------------------------

    <packet_int_no>         The software interrupt vector number used by
                            the packet driver program. This can be from
                            96 to 128.

    [/option]               Includes the following:

      /h                    Show available parameters

      /d                    Delay Initial - The driver program will not
                            initialize the network interface card until
                            the packet driver program is accessed by its
                            upper layer program.

      /w                    This parameter is only to be used in the
                            Windows environment.

      /u                    Unload the packet driver.

      /n                    NetWare conversion. Convert 802.3 packets
                            to 8137 packets

      /autosense            This is the default setting, Auto detect the speed
                            and duplex mode.

      /line_speed=10        Set speed to 10M bps.

      /line_speed=100       Set speed to 10M/100M bps.

      /slot=[1~f]           Select the slot to work with.

      /turbo                Disable PCI post write on Intel PCI chipset which
                            gives the PCI bus higher priority over the other
                            bus (EISA or ISA)

      /tp_full_duplex       Select Twisted Pair interface running in full
                            duplex mode.

      /io=[0xd000~0xef80]   Select the IO base address.

      /int=[1~f]            Select the adapter hardware INT number.


Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web4, load: 0.35